ADVANTECH MIO-2375 Board Computers User Manual

Note 1: For more information regarding MIO-2375, refer to the Advantech website for further information.
Note 2: Acrobat Reader is required to view any PDF

Specifications

General

CPU:
- Intel® i7-1185G7E/1185GRE quad-core, base frequency 1.8 GHz, max. turbo frequency 4.4 GHz
- Intel® i5-1145G7E quad-core, base frequency 1.5 GHz; max. turbo frequency 4.1 GHz
- Intel® i3-1115G4E dual-core, base frequency 2.2 GHz; max. turbo frequency 3.9 GHz
System Memory
- Dual-channel, onboard LDDR4x @ 4267 MHz, up to 32 GB
Cache
- Intel® i7-1185G7E/1185GRE: 12 MB
- Intel® i5-1145G7E: 8 MB
- Intel® i3-1115G4E: 6 MB
BIOS: AMI uEFI 256 Mbit

Watchdog Timer: 255 timer intervals, programmable via software; multi-level WDT (configured via iManager)
Battery: Lithium 3 V/210 mAH

Audio: High definition (HD) audio, Line-In, Line-Out, Mic-In

Expansion Interface

1 x M.2 B-Key 2242/3042 (M-Key available upon request)
1 x M.2 E-Key 2230

Display

Controller: Intel® Iris® Xe Graphics
Maximum Resolution:
- Display Port: DP 1.4 (DP++), up to 4096 x 2304 x 36 bpp @ 60 Hz; with DSC 7680 x 4320 x 30 bpp @ 60 Hz
- Embedded DisplayPort: eDP 1.4 HBR3, up to 4096 x 2304 x 36 bpp @ 60 Hz; with DSC 7680 x 4320 x 30 bpp @ 60 Hz
- Optional MIPI-DSI: MIPI-DSI 2.5 GHz, up to 3200 x 2000 x 24 bpp @ 60 Hz; with DSC 5120 x 3200 x 24 bpp @ 60 Hz
- Dual Display: DP + eDP/MIPI-DSI

Ethernet Interface

Speed: 10/100/1000 Mbps
Controller: GbE1 – Intel i219, GbE2 – Intel i210-AT

Mechanical and Environmental

Dimensions: 100 x 72 mm/3.9 x 2.8 in
Power Supply Type: Supports ACPI
Power Requirements: +12 V ± 10% (supports 2-pin AT power connector and DC jack as a default)
Operating Temperature: 0 ~ 60 °C/32 ~ 140 °F Extended: -40 ~ 85 °C/-40 ~ 185 °F
Weight: 0.26 kg/0.57 lb

Jumpers and Connectors

The board features several jumpers that allow the system to be configured according to the application. The function of each jumper and connector is listed below..

Jumpers
Label	Function
SW1	Automatic Power On Setting
VDD1	LCD Power Setting

Connectors
Label	Function
CN1	Front panel
CN2	GPIO
CN3	I2C
CN4	FAN
CN5	DC power in
Battery1	RTC battery
EDP1	eDP
BL1	Inverter power output
DP1	DP++
USB1	USB2.0+3.2
USB3	Internal USB
M2_1	M.2 E-key
M2_2	M.2 B/M-key
SIM1	Nano SIM
LAN1	RJ45_2x1_W/XFMR&LED
SATA1	SATA_7V
Audio1	Audio
COM1	COM1
COM2	COM2

Jumpers and Connectors (Cont.)

SW1	Automatic Power On Setting
Setting	Function
(1-8) on	AT mode (default)
(1-8) off	ATX mode
(3-6) on	Clear CMOS
(3-6) off	Normal (retain CMOS)
(2-7) (4-5)	Test only

Load BIOS Defaults

Step 1: Power off the device
Step 2: Move the DIP switch from Position 3 to 6, then power on the device
Step 3: Access the BIOS and load default settings (do not clear time or clear CMOS) Pop out to remind users to shut the device down and move the DIP switch from Position 6 to 3.

Step 4: Restart the device

Clear CMOS

Remove the battery (battery 1) The system will stop for 3 seconds, show checksum errors, and clear time settings.

VDD1	LCD Power
Setting	Function
(1-3)	+3.3V (default)
(3-5)	+5V
(3-4)	+12V

Caution: The computer is provided with a battery-powered real-time clock circuit. Batteries are at risk of ex-ploding if incorrectly replaced. Replace only with same or equivalent type as recommended by the manufacturer. Discard used batteries according to manufacturer’s instructions.