Abl Flip-S in Desk Power Module
PRODUCT INFORMATION
Thank you for purchasing ABL’s Flip-S power module. Flip-s has been manufactured and tested in accordance with relevant standards (see contact page).
OVERVIEW
INSTALLATION
Note: Before making a cut-out, please contact your supplier to provide you with a technical drawing with the required table cut-out dimensions. Ensurethat there is a sufficient clearance, 150mm below surface and 30mm between the cut-out edge of the work surface.
- Step 1.
- Lift the clips and slide the side fixings down.
- Lift the clips and slide the side fixings down.
- Step 2.
- Place the module into the table cut-out.
- Place the module into the table cut-out.
- Step 3.
- Pull the sliding fixings back up until the module is tightened to the table.
- Pull the sliding fixings back up until the module is tightened to the table.
MAIN FEATURES
- The Aluminium lid and modular parts are available in Black, White, and Grey
- Completely configurable, available in variations of sockets, USB charge sockets, and media connections
- Rated voltage of Flip-s power module unit is 250V AC (C, E, F, G, J, L), for B-type sockets 120V AC
- Nominal intensity of the unit:
- 13A for G type socket
- 16A for B, C, E, F, J, L type sockets
- G-type sockets are individually fused with 3.15A or 5A fuse. Available in up to four sockets with 5A fuse, and in up to six sockets with 3.15A to comply with BS6396
- Fit desk thickness between 10 and 40 mm
- All standard options come with 0.5m drop lead to 3 Pole Connector. Cable type: H05VV-F 3×1.5 mm?
- Switch is available only with G socket type.
*The most common socket types:
Please contact us for more information
SAFETY INFORMATION
SAFETY NOTES:
- Items such as Vacuum Cleaners, Kettles, Coffee Makers, and Fan Heaters should not be connected via these power modules
- Installation is to be carried out by a qualified professional
- Complies with BS 5733 (UK) IEC 60884-1 and IEC 60884-2-7 (Europe)
- Manufacturing in-house within central Europe under strict compliance with ISO 9001:2015
CONTENTS
Flip-S power module
MAINTENANCE
Do not open, disassemble, change, or modify the device. Every unauthorized opening or repair of the device leads to a loss of warranty. During device usage, you need to follow basic safety measures. since safety requirements vary, please check with local laws.
WARRANTY
WARRANTY CONDITIONS
ABL warrants this product as free of defects in material, design, and workmanship for the period of twenty-four (24) months from the original date of receipt of the product unless applicable national laws stipulate otherwise. If during the period of warranty, this product proves defective under normal use and service you should return the product to the retailer from whom it was originally purchased. The liability of the ABL is limited to the cost of repair and/or replacement of the unit under warranty. The warranty is void if a failure occurs due to the following reasons:
- Improper device installation
- Improper handling
- Improper transport
- Force majeure
WARNING: Do not use this product for any other purpose other than what it was designed for.
CONTACT INFORMATION
- UK DISTRIBUTION CENTRE
- Unit A6 Brooklands Technology Park, Wellingborough Road, Sywell, Northamptonshire, NN6 OBN, United Kingdom
- United Kingdom
- +44 (0) 1933 400 080
- sales@abl-Itd.com
- EMEA DISTRIBUTION CENTRE
- Lava Tolstoja 25 32103 Cacak Serbia
- +381 (0) 32 420 100
- sales@abl-itd.com
MORE INFO
SCAN ME
Documents / Resources
 |
Abl Flip-S in Desk Power Module [pdf] User Manual Flip-S in Desk Power Module, Flip-S, in Desk Power Module, Power Module, Module |
