A BETTER BLIND RCM25 Low Power Battery with Built in Zigbee Motor Instruction Manual

MOTOR FEATURES

• Energy saving design, powered by large capacity Li-ion battery;
• Motor can do both RF remote control and APP control via Zigbee communication protocol
• Easy operation intelligent motor; programming can be set with either remote or smart phone APP.
• Patented smooth and quiet design; Soft start and soft stop;
• Running noise level lower to 35dB.
• Automatic low battery buzzer warning remind you to charge motor.
• Motor can set 6 limit, including top/bottom limits and 4 favorite intermediate limits.
• Various user friendly features on APP setting.

POWER SOURCE & CHARGING

• Built-in Li-ion battery supply. Recharged using an external charging kit include a charger block and one USB-C charging cable.
• Motor one full charge ca be used for 4-6 months vary with shade use frequency.
• Charging time is 6-8 hours;

Tips:

1. For longer life service of the motorized shade. we suggest all lion battery motor need to charge battery every 6 months to avoid battery over discharge.
2. Please turn the switch to “1” on the motor head before charging
3. Please charge the motor for around 6 hours until see the green light before first use

REMOTЕ LAYOUT

Duct outer dimensions (W x H x D):
477.2 x 42.75 x 47.7mm
Inner tube dimensions: 25 mm

Duct outer dimensions (W x H x D):
477.2 x 42.75 x 47.7mm
Inner tube dimensions: 25 mm

Duct outer dimensions (W x H x D):
541.7 x 42.75 x 47.7mm
Inner tube dimensions: 28 mm

Operation Instruction

Power ON/OFF

* After switching off power, the motor will not be able to receive remote signals.

• Power ON
  Turn the switch to “1”, turn on motor. Motor response “beep” one time
  
• Power OFF
  Turn the switch to “0”, turn off motor
  

Programming Preparation

* If there is no action in 10 seconds, the motor will exit programming automatically.

• Method A
  Press PROG button for 1s
  
  motor will beep and then jog once The motor now is in the setting mode
  
• Method B
  If a remote had paired with a motor Press and hold STOP button on programmed remote for 5s
  
  Motor jogs once. The motor is now in setting mode
  

Paring remote

Press UP button under paring mode

Motor jogs once, the motor and remote are now paired

Change running mode (two modes)

(Continuously mode: when you hit the up/down button, motor will immediately run to next limit)
(Jogging move mode: when you hit the up/down button less than 1″, motor only jog, keep press for more than 1″, motor will keep running)

Press the STOP button for 5 seconds motor will jog once enter programming mode

Press the STOP button again

Motor will jog once confirm the running mode, the motor running mode is now reversed

Change direction

Press the STOP button for 5 seconds motor will jog once enter programming mode

Motor will jog once enter programming mode

Press the DOWN button again

Motor will jog once confirm the reverse direction

TOP limit setting

Press the LEARN button on the back of remote.

The motor jogs once, it is now in setting mode.

Press UP button make shade to top limit position.

Press the LEARN button on the back of remote again.

motor will jog once confirm the top limit position.

Bottom limit setting

Press the LEARN button on the back of remote

The motor jogs once, it is now in setting mode

Press DOWN button make shade to bottom limit position

Press the LEARN button on the back of remote again

motor will jog once confirm the bottom limit position

Other limit position setting

If there’s no any action within 30’s, the motor will exit from limit position preparation automatically

You can set 4 limits between top and bottom limits

Adjust the motor to desired position, press STOP, then press PROG for 1s

The motor jogs once, it gets into setting mode

Press PROG button again

The motor jogs once again, the limit position setting is done

Limit position fine-tuning

Move the shade to the limit that you want to adjusted Press the LEARN button on the back of remote

The motor jogs once, it gets into setting mode

Press up/down move the shade to new limit position

Press LEARN button to save settings

motor will jog once confirm the new limit position

Delete Single Channel program

(if you want to remove one channel’s setting, pls do as follow)

Press the STOP button for 5 seconds

motor will jog once enter programming mode

Press the LEARN button on the back of remote for 1″

Motor jogs once, single channel is deleted

Delete the limit position

Let the shade run to the limit position which needs to be deleted, press LEARN for 7s

The motor jogs once after 1s then goes into setting mode

The motor jogs once again after 7s, the preset limit position is now deleted

Motor Speed Adjustment

Press the UP+DOWN button at the same time for 5″

motor jog once enter speed adjustment programming mode

Press UP button Motor set in High Speed Mode 35rpm

Press STOP button Motor set in Standard Speed Mode 25rpm

Press DOWN button Motor set in Quiet Speed Mode 20rpm

Reset motor

* Make sure the interval between every actions less than 1s

(Two methods, one on the remote, another one on motor head)

• Method A
  Press STOP of the programmed remote for 5s
  
  motor will jog once enter programming mode
  
  KEEP Press the LEARN button of remote for 5″
  
  motor will jog once at the 1st second and jog twice at 5th second
  
• Method B
  Press the PROG button on motor head for 5 times
  
  The first 4 times 1″ a time, each time will beeр
  
  The 5th time keep holding it for 5 seconds until motor jog twice
  

Set motor to ZIGBEE pairing mode

Make sure the interval between every actions less than 1s

(Two methods, one is use remote, another is set on motorhead)

• Method A: Set on remote
  Press STOP of the programmed remote for 5s
  
  motor will jog once enter programming mode
  
  Press the UP+DOWN button at the same time for 5″
  
  motor will jog and GREEN LED will flash on motor head Now motor enter ZIGBEE pairing mode
  
• Method B: Set on motor head
  Press the PROG button on motor head for 4 times (2 times short time press, and 2 times long time press)
  
  2 times short time press, each time 1″, motor will beeр
  
  The 3rd time keep press 3″, you will hear beep at the 1st second and beep again at 3rd second
  
  The 4th time keep press 3″, you will hear beep at the 1st second and beep and motor jog once at 3rd second
  

Supplemental Instruction

• a. Max. 6 limit stop positions. (Upper limit/Lower limit and 4 intermediate limit positions)
• b. When the first limit position is the up limit position, all other limit positions can only below this position; the same thing, when the first limit position is the down limit position, all other limit positions can only be set above this position. can’t be delete
• c. Every limit position can be fine-turned or deleted separately (the first limit position can only be fine-tuned but can’t be deleted separately. It can be deleted
  when delete all memories) d. Under the jog mode, short press the up or down button, motor jogs once. Press the up or down button for more than 1s, and the engine moves to the limit positions.
• e. Under the continuous move mode, quickly press the up or down button twice on the transmitter, and the motor will go directly to the up or down limit stop position without stopping at the middle limit position.
• f. The light is red when charging and will turn to green when fully charged.
• g. The motor will stop when the voltage is under 6.8V, and start working at 6.9V; motor moves under 7.0V, the motor will beep continuously (the working voltage)
  Battery shortage alarm:
  The motor will start to beep when the battery capacity is below 7.0V, yet it is still in continuous move mode.
  The motor will step into jog mode and continuously beep when the battery capacity is below 6.8V, which means you must charge the motor now.
• h. The motor needs to unlock in a different direction when it is blocked; Need to change the jog mentioned direction if the direction is the same as the jog direction.
  When the motor is blocked, it needs to be unlocked in reverse, and if it is in the same direction as the shaking, change the direction of the shaking prompt
• I. The charge cable needs to have the data transfer function.
  Motor charging needs to use TYPE-C charging cable with data transmission function.

Trouble Shooting

Item	Problem	Matter	Shooting
1	The motor doesn’t work and no any move	A. Power is cut off B. Shortage voltage protection C. Incorrect installation leads to motor stocking	A. Switch it on by button B. Start the motor after charging it for 6 hours C. Check and make sure all parts are installed properly
2	The motor stops suddenly during operation	A. Shortage voltage protection B. Protect the motor when encounter obstacle	A. The motor will resume to work after being charged B. Check if there is something stuck or overloading

Notice:
This device contains licence-exempt transmitter(s) receiver(s) that comply with Innovation, Science and Eco monic Development (ISED) Canada’s licence-exempt RSS(s). “;

Operation is subjected to the following two conditions.

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The distance between user and products should be no less than 20cm. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by taming the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radioTV technician for help.

This device contains licence-exempt transmitter(s)receiver(s) that comply with innovation, Science and Economic Development (ISED) Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
The device has been evaluated to meet general RF exposure requirement.
The distance between user and products should be no less than 20cm.

Zigbee Motor APP Setting Instruction

Scan to download “Smart Life” APP

Smart Life – Smart Living 4+
Smart Living
Volcano Technology Limited
#46 in Lifestyle
4.7 265.2K Ratings
Free Offers In-App Purchases

Apple Store(iOS)

Google Play(Android)

Add Mini-Multi Gateway -Hub to Smart Life APP

(To achieve remote access control shades outside your home, you must need to buy a Bluetooth Gateway Hub)

1. Power on Mini-Multi gateway hub
2. there are two indicator on the hub;
   • when blue LED keep lighting, red LED slowly blinking, mini hub is in pairing mode
   • After you successfully add the mini hub to Smart Life APP, blue and red LED will keep lighting on you can keep holding reset button around 30 seconds; it will turns to blue light is on, red blinking; if you can’t see that signal, keep pressing the reset button for another 10 seconds; once the hub reset, the hub will remove from your APP and there are two methods to add the mini hub; 1. auto scan adding; 2.manually adding.

• Register and login “Smart Life” APP
  
• Add device, refer to red part.
  
  After you choose “Add Device” now you put motor in
  No devices Bluetooth pairing mode.
  Add Device Please refer to below instruction.
• “Add device”, the APP will scan devices nearby. When the APP discover the hub, choose “Add”
  
• Choose 2.4G WiFi and input WiFi password direct the hub to network Click “Next”, when you see “added successfully”, the hub now is added to APP.
  

Add Zigbee motor to gateway hub

• in the hub control menu choose “Zigbee device list”, click “Add devices”
  
• put motor to zigbeе pairing mode (refer to above)
  Next step tips:
  Send motor to Zigbee pairing mode
  Refer to follow operation
  Set motor to Zigbee paling mode
  
• when the hub discover zigbee motor in range, click “NEXT” when you see motor is “added successfully”, click “Done” now the motor is added to the hub.
  

APP control functions overview

Third Party Control Instruction–Alexa & Google Assistant

• Access to shade control menu Tap red box as above
  
• Choose “Third-party Control”
  
• There will be two options Alexa & Google Assistant
  
  Tips: Alexa voice command
  Alexa, open “shade one”
  Alexa, close “shade one”
  Alexa, set “shade one” to 50%
• Choose
  “Link to Amazon Alexa”
  “Link to Google Assistant”
  
• Choose “Link”
  then it will enable your Smart Life account to third parties account
  
• Now you can discover your devices on third parties APP
  

Documents / Resources

A BETTER BLIND RCM25 Low Power Battery with Built in Zigbee Motor [pdf] Instruction Manual 2BEZU-RCM25, 2BEZURCM25, rcm25, RCM25 Low Power Battery with Built in Zigbee Motor, RCM25, Low Power Battery with Built in Zigbee Motor, Power Battery with Built in Zigbee Motor, Battery with Built in Zigbee Motor, Built in Zigbee Motor, Zigbee Motor, Motor

References

• User Manual