SNR S2995G-12FX Managed L3 Ethernet Switch
Product Usage Instructions
Front and Back Panels Description
Refer to the manual for detailed LED indicators and port descriptions.
Install the Device on a Worktable
Stick the rubber gasket and install the device on a worktable securely.
Connect the PGND Cable and Power Cable
Connect the grounding cable to the ground bus and then to the switch. Connect the AC power cable to power the switch.
Access to Initial Switch Configuration:
Access via Console:
Connect console cable to the switch via RJ-45 connector and the other end to the RS-232 port of the PC. Use the following settings for the COM-port:
- Bitrate: 115200
- Databits: 8
- Parity: None
- StopBits: 1
- Flow Control: None
Use default username ‘admin’ and password ‘admin’ to access the switch.
Access via Ethernet Port:
Default IP-address: 192.168.1.1, Default username: admin, Default password: admin.
Frequently Asked Questions (FAQ):
Q: How do I access technical support for the product?
A: You can reach NAG service and technical support center at the following details:
SNR-S2995G-12FX Quick Install Guide
This guide describes the steps of installing the switch, including the basic introduction to the product, the basic installation steps, etc.
Front and back panels description
| № | Item | Description | |
| 1 | Ports 1-4 | Copper Combo ports 10/100/1000BaseT | |
| 2 | Ports 1-4 | SFP Combo ports 100/1000BaseX | |
| 3 | Ports 5-12 | SFP 100/1000BaseX ports | |
| 4 | Ports 13-16 | SFP+ 1/10GbE ports | |
| 5 | Console | Console port | |
| 6 | MGMT | Management port | |
| 7 | USB | USB port | |
| 8 | Ports 1-4 | Copper Combo port LEDs | |
| 9 | 1-16 | Port LEDs | |
| Off | No link on port | ||
| Green | The port has a valid link | ||
| Green (Blink) | Blinking indicates activity on port | ||
| RPS | RPS LED | ||
| Off | Switch work from AC power | ||
| Green | AC is off. Switch work from battery | ||
| DIAG | Switch status LED | ||
| Green | System is starting or abnormal | ||
| Green (Blink) | System works normally | ||
| PWR | Power LED | ||
| Green | Internal/External power is operating normally | ||
| Off | Power off | ||
| 9 | MGMT | Management port LED | |
| Off | No link on port | ||
| Green | The port has a valid link | ||
| Green (Blink) | Blinking indicates activity on port | ||
| 10 | 100-240V~ 50/60Hz | The AC power socket, AC rated voltage range: 100-240V AC; 50/60Hz | |
| 11 | DC 11-13V 4.5A | RPS port, 11-13V DC | |
| 12 | Grounding | The Grounding bolt | |
Switch installation
Before installation, take ECD-preventive measures, such as wearing the ESD-preventive gloves or a wrist strap.
Install the Device in a 19” Cabinet
Fix the Rack Mount Brackets.
Fix the captive nuts， and install the device in a cabinet. Attention: leave more than 1U space between the devices for proper heat dissipation. 
Install the Device on a Worktable
Stick the rubber gasket， and install the device on a worktable.
Connect the PGND cable and power cable
Connect grounding cable to the ground bus and to the switch. 
Connect the AC power cable.
Access to initial switch configuration
Access to the switch via console
Connect console cable to switch via RJ-45 connector and another side to RS-232 port of the PC. Settings of the COM-port are below.
| Parameter | Value |
| Bitrate | 115200 |
| Databits | 8 |
| Parity | None |
| StopBits | 1 |
| FlowControl | None |
Use default username admin and password admin to access the switch.
Access to the switch via Ethernet port
Connect the Switch with the PC NIC interface. Power on the Switch. Check whether the IP-address of the computer is within this network segment: 192.168.1.xxx (“xxx” ranges 2~254), for example, 192.168.1.100. Open the browser, and enter http://192.168.1.1 and then press «Enter» or open telnet connection to address 192.168.1.1.
| Parameter | Value |
| Switch default IP-address | 192.168.1.1 |
| Default username | admin |
| Default password | admin |
Technical support
- NAG service and technical support center:
- NAG LLC
- Address: Office M-03, Al Garhoud Business center Building. UAE, Dubai
- Website: snr.global
- Technical support portal: snr.support
- Tel: +971 0 42599967
Documents / Resources
 |
SNR S2995G-12FX Managed L3 Ethernet Switch [pdf] Installation Guide S2995G-12FX Managed L3 Ethernet Switch, S2995G-12FX, Managed L3 Ethernet Switch, Ethernet Switch, Switch |
