HT1 Thermostat Touch
Screen Nyore Kuronga
Bhuku reMirayiridzo

	Bata Screen
	Simple Programming
	5 + 2 / 7 Mazuva Mapurogiramu
	Mushandisi-ushamwari Menyu
	Vertical / Horizontal modhi

INSTALLATION UYE WIRING

Nyatsoparadzanisa hafu yepamberi yethermostat kubva mundiro yekumashure nekuisa diki diki diki diki terminal mudhiraivha mumitsetse yepasi pechiso chethermostat.
Nyatsosunungura tambo yekubatanidza iyo yakavharirwa mukati mehafu yepamberi ye thermostat.
Isa thermostat yepamberi hafu pane imwe nzvimbo yakachengeteka.
Tevedza Wiring Dhiyagiramu kuita wiring.
Nyora thermostat yekumashure ndiro pabhokisi reku flush Batanidza tambo ye thermostat wochekerera mahafu maviri pamwechete.

DIMENSIONS

WIRING DIAGRAM

LCD SYMBOLS

	simba pa / kudzima
M	mode bhatani / menyu bhatani chirongwa bhatani
	simbisa zvigadziriso
	kuwedzera
	kuderedza
	auto mode
	Chinyorwa modhi
	kiyi yekukiya chiratidzo
	kupisa kunobatidzwa
P1, P2, P3, P4	nhamba dzepurogiramu
SET	set tembiricha
Er	sensor haina kuiswa kana kukanganisa
A	mhepo inonzwa mode
F	floor sensing mode
FA	air & floor sensing mode

ZVAKAITIKA ZVINO

SECIFICATIONS
SUPPLY VOLTAGE	5°C ~35°C
KUCHINJA KUNYANYA	230-240 VAC
TEMP RANGE(A)	16A
PASI SENSOR kuramba kusamira kusvika 25°C	10 Kohm.
IP RATING	30
ORIENTATION	VERTICAL

KUGADZIRA ZVIRONGWA ZVOKUSHANDA

Kwemazuva 7 programmable mode
Default Settings

	MONDAY – SVONDO
PROGRAM	NGUVA	TEMP
P1	7	22°
P2	9.3	16°
P3	16.3	22°
P4	22.3	16°

Dzvanya uye M bata kwemasekonzi mashanu, kuratidzwa kwezuva kuchapenya.
Shandisa iyo miseve kusarudza zuva.
Dzvanya uye ubate iyo museve kwemasekonzi mashanu kusarudza ese mazuva manomwe evhiki, uye kudzima dzvanya uye ubate museve kwemasekonzi mashanu zvakare.
Dzvanya M, nguva yeP1 ichapenya.
Shandisa iyo miseve kugadzirisa nguva yeP1.
Dzvanya M, tembiricha yeP1 inopenya.
Shandisa iyo miseve yekugadzirisa tembiricha yeP1.
Dzvanya M, nguva yeP2 ichapenya.
Shandisa iyo miseve kugadzirisa nguva yeP2.
Dzvanya ，M tembiricha yeP2 ichapenya.
Shandisa iyo miseve yekugadzirisa tembiricha yeP2.
Dzokorora pamusoro nhanho dzeP3 uye P4.

Cherechedza:
NeMugovera neSvondo,
kana uchida kubvisa nguva yeP2 neP3, dzvanya
Dhinda zvakare kukanzura. panguva yepurogiramu.

KUGADZIRA ZVIRONGWA ZVOKUSHANDA

Yemazuva 5 + 2 inorongwa modhi (default)
Default Settings

	MONDAY – FRIDAY		MUSIRO – SVONDO
PROGRAM	NGUVA	TEMP	NGUVA	TEMP
P1	7	22°C	7	22°C
P2	9.3	16°C	9.3	16°C
P3	16.3	22°C	16.3	22°C
P4	22.3	16°C	22.3	16°C

Nzira yekushandura mapurogiramu eMuvhuro-Chishanu?
Dzvanya uye ubate kwemasekonzi mashanu, nguva yeP5 ichapenya.

Shandisa iyo miseve kugadzirisa nguva yeP1.
Dzvanya M, tembiricha yeP1 inopenya.
Shandisa iyo miseve yekugadzirisa tembiricha yeP1.
Dzvanya M, nguva yeP2 ichapenya.
Shandisa iyo miseve kugadzirisa nguva yeP2.
Dzvanya M, tembiricha yeP2 inopenya.
Shandisa iyo miseve yekugadzirisa tembiricha yeP2.
Dzokorora pamusoro nhanho dzeP3 uye P4.

Nzira yekushandura mapurogiramu eMugovera-Svondo?

Kana mapurogiramu eMuvhuro-Chishanu aiswa, ramba uchidzvanya M, nguva yeP1 ichapenya.
Shandisa iyo miseve kugadzirisa nguva yeP1.
Dzvanya M tembiricha yeP1 inopenya.
Shandisa iyo miseve yekugadzirisa tembiricha yeP1.
Dzvanya M, nguva yeP2 ichapenya.
Shandisa iyo miseve kugadzirisa nguva yeP2.
Dzvanya M, tembiricha yeP2 inopenya.
Shandisa iyo miseve yekugadzirisa tembiricha yeP2.
Dzokorora pamusoro nhanho dzeP3 uye P4.

Cherechedza:

NeMugovera neSvondo,
kana uchida kubvisa nguva yeP2 neP3, dzvanya panguva yepurogiramu.
Press zvakare kukanzura.

KUCHINJA PARAMETER ZVINOKOSHA

Dzima thermostat nekudzvanyaMushure mekudzima thermostat, tinya M Menyu inotevera icharatidzwa.
Shandisa iyo miseve kugadzirisa.
PressM kuti uende kune inotevera menyu.
Press kuchengeta nekubuda.

1. Sensor Modhi: A / AF / F
   A = Kunzwa Mhepo Chete (Yakavaka mukati sensor)
   AF = Mhepo & Floor inonzwa (Floor probe inofanira kuiswa)
   F = Floor Sensing (Floor probe inofanira kuiswa)
2. Kuchinja Kusiyana
   1°C, 2°C….10°C ( 1°C by default)
3. Air Temp Calibration
   -5°C ~ 5°C ( 0°C by default)
4. Floor Temp Calibration
   -5°C ~ 5°C ( 0°C by default)
5. Nguva Yekubuda Yega
   5 ~ 30 seconds ( 20 seconds by default)
6. Temperature Ratidza Mode
   A: ratidza tembiricha yemhepo chete (nekusarudzika)
   F: kuratidza tembiricha yepasi chete
   AF: ratidza mhepo uye tembiricha yepasi zvakachinjana
7. Max Floor Temp Limit
   20°C ~ 40°C (40°C by default)
8. Backlight Timer
   0,10,20,30,40,50,60, ON ( 20 seconds by default)
9. Clock Format
   12 / 24 Hour clcok fomati ( 24 Hour wachi nekusarudzika)
10. Kudzivirira kwechando
    00 ,01 (yagara iripo 00=haina kuvhurwa, 01=yakabatidzwa)
11. 5 + 2 / 7 Zuva Chirongwa Sarudzo
    01 = 5+2 Zuva Chirongwa, 02= 7 Zuva Chirongwa (default 01)

KUITA NGUVA NEZUVA

Press , nguva yekuratidzira ichapenya.
Shandisa iyo miseve kugadzirisa.
Press , zuva rinoratidza richapenya.
Shandisa iyo miseve kugadzirisa.
Zvino dzvanya kuchengeta nekubuda.

AUTO / MANUAL Mode

Dzvanya M kuti usarudze Auto kana Manual modhi.

Auto maitiro:
Manual mode:

MuManual mode, tinya iyo miseve yekuseta tembiricha yaunoda.
Mune Auto mode, tinya iyo miseve inodarika iyo yazvino programed tembiricha unitl inotevera yakarongwa nguva.

KIYA KEYPAD

Kukiya makiyi, dzvanya wobata kwemasekonzi mashanu, uchaona chiratidzo chekiyi . Kuti uvhure, dzokorora matanho ari pamusoro uye chiratidzo chekiyi chinopera.

TEMPORARY TEMPERATURE PASI

Mune Auto mode, tinya iyomiseve, iyo tembiricha inoratidza ichatanga kupenya.
Shandisa iyomiseve kugadzirisa tembiricha.
Press kusimbisa.

Iye zvino uchaona "O/RIDE" pazasi peratidziro yekushisa. Thermostat yako inochengetedza tembiricha itsva seti kusvika nguva inotevera yakarongwa. Kukanzura kuseta yekupfuura, dzvanya uye bata M kwemasekonzi mashanu.

Zvinyorwa / Zvishandiso

Thermafloor HT1 Thermostat Kubata Screen Nyore Kuronga [pdf] Bhuku reMirayiridzo HT1 Thermostat Bata Sikirini Rakareruka Kuronga Kurongeka, HT1, Thermostat Bata Screen Rakareruka Kurongeka, Bata Screen Rakareruka Kuronga Kurongeka, Nyore Kuronga Kurongeka, Kurongwa Kunorongwa, Kunorongwa

References

• User Manual