Neuro 102 EX
Yakavandudzwa Universal Single Loop
Process Controller
User Manual

Neuro 102 EX Yakavandudza Universal Single Loop Process Controller

Iri bhuku ripfupi rinonyanya kuitirwa kukurumidza kutaridza kune wiring connections uye parameter kutsvaga. Kuti uwane mamwe mashoko pamusoro pekushanda uye kushandiswa; ndapota pinda pa www.ppiindia.net

KUMASHURE PANEL LAYOUT

Keys Operation

Symbol	Key	Function
	PEJI	Dzvanya kuti upinde kana kubuda mumodhi yekuseta.
	PASI	Dzvanya kuti uderedze kukosha kweparameter. Kudzvanya kamwe kunoderedza kukosha nekuverenga kumwe; kuramba wakadzvanya kunomhanyisa shanduko.
	UP	Dzvanya kuti uwedzere kukosha kweparameter. Kudzvanya kamwe kunowedzera kukosha nekuverenga kumwe; kuramba wakadzvanya kunomhanyisa shanduko.
	PINDA OR ALARM BVUMA	Gadzirisa Mamiriro: Dzvanya kuti uchengetedze iyo yakatarwa parameter kukosha uye kuti uende kune inotevera paramende paPEJI. Run Mode: Dzvanya kuti ubvume chero maAlarm akamirira. Izvi zvakare zvinodzima iyo Alarm relay.
	AUTO MANUAL	Dzvanya kuti ushandure pakati peAuto kana Manual Control Mode.
	(1) MURAIRO	Dzvanya kuti uwane ma parameter anoshandiswa seMirairo.
	(1) OPERATOR	Dzvanya kuti uwane 'Operator-Peji' paramita.
	(2) PROFILE	Dzvanya kuti uwane 'Profile Run-Nguva Variables'.

PV Kukanganisa Zviratidzo

Mharidzo	PV Error Type
	Pamusoro-renji (PV pamusoro peMax. Range)
	Under-range (PV pazasi Min. Range)
	Vhura (Sensor yakavhurika / yakaputsika)

KUKUNGAMIRIRA KWEMAGETSI

ENCLOSURE ASSEMBLY

Kukwidza DZIDZO

OUTPUT-5 & SERIAL COMM. MODULE
Cherechedza
Iyo Output-5 Module & Serial Kukurukurirana Module yakaiswa kune rimwe divi reCPU PCB sezvakaratidzwa munhamba (1) & (2) pazasi.

JUMPER SETTINGS

INPUT TYPE & OUTPUT-1

Output Type	Jumper Setting - B	Jumper Setting - C
Relay
SSR Drive
DC Linear Yazvino (kana Voltage)

JUMPER SETTINGS & KUKUMA DETAILS
OUTPUT-2,3 & 4 MODULEZVINHU ZVIMWE ZVOKUGADZIRISA: PEJI 12

Parameters	Settings (Default Value)
Kudzora Kubuda (OP1) Type	(Default: Relay)
Kudzora Chiito	On-Off Pulse PID (Default: PID)
Kudzora Logic	Reverse Direct (Default: Reverse)
Input Type	Refer Tafura 1 (Default: Type K)
PV Resolution	Refer Tafura 1 (Default: 1)
PV zvikamu	(Default: °C)
PV Range Yakaderera	-19999 kusvika kuPV Range High (Default: 0)
PV Range High	PV Range Yakaderera kusvika 9999 (Default: 1000)
Setpoint Yakadzika Muganho	Min. Range yeRudzi rweKupinza rwakasarudzwa kuenda kuSetpoint High Limit (Default : -200.0)
Setpoint Yakakwirira Muganho	Setpoint Low Limit kuMax. Range yeRudzi rweKupinza rwakasarudzwa (Default: 1376.0)
Offset yePV	-199 kusvika 999 kana -1999.9 kusvika ku9999.9 (Default: 0)
Digital Sefa Nguva Inogara	0.5 kusvika 60.0 Sekondi (mumatanho e0.5 Sekondi) (Default: 2.0 Sec.)
Sensor Break Output Power	0 kusvika 100 kana -100.0 kusvika 100.0 (Default: 0)

ZVINHU ZVINOITA: PEJI 10

Parameters	Settings (Default Value)
Proportional Bhendi	0.1 kusvika 999.9 Units (Default: 50 zvikamu)
Integral Time	0 kusvika 3600 Sekondi (Default : 100 Sec.)
Derivative Time	0 kusvika 600 Sekondi (Default : 16 Sec.)
Cycle Time	0.5 kusvika 100.0 Sekondi (mumatanho e0.5 secs.) (Default : 10.0 Sec.)
Relative Cool Gain	0.1 kusvika 10.0 (Default: 1.0)
Nguva Inotonhorera Yekutenderera	0.5 kusvika 100.0 Sekondi (mumatanho e0.5 secs.) (Default : 10.0 sec.)
Hysteresis	1 kusvika 999 kana 0.1 kusvika 999.9 (Default: 0.2)
Parameters	Settings (Default Value)
Pulse Nguva	Pulsa ON Nguva kusvika 120.0 Sekondi (Default: 2.0 sec.)
Nenguva	0.1 kune Kukosha kwakagadzirirwa kwePulse Nguva (Default: 1.0)
Cool Hysteresis	1 kusvika 999 kana 0.1 kusvika 999.9 (Default: 2)
Nguva Yakanaka Pulse	Kutonhorera ON Nguva kusvika 120.0 Sekondi (Default: 2.0)
Kutonhorera ON Nguva	0.1 kune Kukosha kwakagadzirirwa Kutonhorera Pulse Nguva (Default: 1.0)
Kupisa Simba Kuderera	0 kusvika Power High (Default: 0)
Kupisa Simba Kumusoro	Simba Yakaderera kusvika 100% (Default: 100.0)
Cool Power Low	0 kusvika Kutonhorera Power High (Default: 0)
Cool Power High	Kutonhorera Simba Kudzika kusvika 100% (Default: 100)

ZVINOTARISIRA PARAMETERA: PEJI 13

Parameters	Settings (Default Value)
Self-Tune Command	(Default: Kwete)
Overshoot Inhibit	(Default: Disable)
Overshoot Inhibit Factor	1.0 kusvika 2.0 (Default: 1.0)
Auxiliary Setpoint	(Default: Disable)
Rekodha (Retransmission) Kubuda	(Default: Disable)
Kugadziriswa kweSP pane Yepasi Readout	(Default: Vhura)
Kugadziriswa kweSP pane Operator Peji	(Default: Vhura)
Manual Mode	(Default: Disable)
Alarm SP Kugadziridzwa pane Operator Peji	(Default: Disable)
Standby Mode	(Default: Disable)
Profile Bvisa Command pane Operator Peji	(Default: Disable)
Baud Rate	(Default: 9.6)
Kukurukurirana Parity	Hapana Kunyange Odd (Default: Kunyange)
Controller ID nhamba	1 kusvika 127 (Default: 1)
Kukurukurirana Nyora Inogonesa	(Default: Kwete)

OP2 & OP3,OP4,OP5 BASA PARAMETERS: PEJI 15

Parameters	Settings (Default Value)
Output-2 Basa Sarudzo	Hapana Kupera kweProfile Kutonhorera Kwakanaka (Default: Hapana)
Output-2 Type	(Default: Relay)
OP2 Chiitiko Status	(Default: ON)
OP2 Chiitiko Nguva	0 kusvika 9999 (Default: 0)
OP2 Chiitiko Nguva Zvikamu	Sekondi Maminitsi Maawa (Default : Sekondi)
Output-3 Basa Sarudzo	Hapana Alarm Kupera kweProfile (Default: Alarm)
Alarm-1 Logic	Normal Reverse (Default: Zvakajairika)
OP3 Chiitiko Status	(Default: ON)
OP3 Chiitiko Nguva	0 kusvika 9999 (Default: 0)
OP3 Chiitiko Nguva Zvikamu	(Default : Sekondi)

Parameters	Settings (Default Value)
Alarm-2 Logic	Normal Reverse (Default: Zvakajairika)
Recorder Transmission Type	Process Value Setpoint (Default : Process Value)
Recorder Output Type	(Default: 0 kusvika 20mA)
Recorder Low	Min. kuna Max. Range Yakatsanangurwa Yemhando Yakasarudzwa Yekupinza (Default : -199)
Recorder High	Min. kuna Max. Range Yakatsanangurwa Yemhando Yakasarudzwa Yekupinza (Default: 1376)

ALARM PARAMETTER: PEJI 11

Parameters	Settings(Default Value)
Alarm-1 Type	Hapana Process Low Process High Deviation Band Window Band (Default: Hapana)
Alarm-1 Setpoint	Min. kuna Max. Range yakatsanangurwa kune yakasarudzwa Input Type (Default: Min kana Max Range)
Alarm-1 Deviation Band	-999 kusvika 999 kana -999.9 kusvika 999.9 (Default: 5.0)
Alarm-1 Window Band	3 kusvika 999 kana 0.3 kusvika 999.9 (Default: 5.0)
Alarm-1 Hysteresis	1 kusvika 999 kana 0.1 kusvika 999.9 (Default: 2)
Alarm-1 Inhibit	(Default: Hongu)
Alarm-2 Type	Hapana Process Low Process High Deviation Band Window Band (Default: Hapana)
Alarm-2 Setpoint	Min. kuna Max. Range yakatsanangurwa kune yakasarudzwa Input Type (Default: Min kana Max Range)
Alarm-2 Deviation Band	-999 kusvika 999 kana -999.9 kusvika 999.9 (Default: 5.0)
Alarm-2 Window Band	3 kusvika 999 kana 0.3 kusvika 999.9 (Default: 5.0)
Alarm-2 Hysteresis	1 kusvika 999 kana 0.1 kusvika 999.9 (Default: 2.0)
Alarm-2 Inhibit	(Default: Hongu)

PROFILE ZVINHU ZVIMWE ZVOKUGADZIRISA: PEJI 16

Parameters	Settings (Default Value)
Profile mode sarudzo	(Default: Disable)
Nhamba Yezvikamu	1 kusvika 16 (Default: 16)
Nhamba Yekudzokororwa	1 kusvika 9999 (Default: 1)
Common Holdback	(Default: Hongu)
Output Off	(Default: Kwete)
Power Fail Strategy	(Default: Ramba)

PROFILE KUGADZIRIRA ZVINHU: PEJI 14

Parameters	Settings (Default Value)
Chikamu Nhamba	1 kusvika 16 (Default: 1)
Target Setpoint	Min. kuna Max. Range yakatsanangurwa kune yakasarudzwa Input Type (Default : -199)
Nguva Yenguva	0 kusvika 9999 Maminitsi (Default: 0)
Holdback Type	(Default: Hapana)
Holdback Value	1 kusvika 999 (Default: 1)

PROFILE STATUS RUZYO: PEJI 1

Lower Readout Prompt	Upper Readout Information
	Active Segment Number
	Segment Type
	Target Setpoint
	Rampmu Setpoint
	Balance Time
	Kuenzanisa Kunodzokorora

ZVINHU ZVINHU ZVINHU ZVINHU ZVINHU PEJI 2

Parameters	Mhedzisiro pachikamu chekumhanya
Nguva Yenguva	RAMP:- Kuchinja nguva yenguva kuchaita pakarepo 'Ramp Rate' yechikamu chazvino. NYONGA:- Yakapfuura nguva kusvika parizvino haina kufuratirwa uye iyo soak timer inotanga kuverenga ichidzika kusvika 0 kubva pane yakashandurwa nguva yenguva kukosha.
Holdback Type	Iyo yakagadziridzwa Holdback Band Type inoiswa ipapo ipapo pane yazvino chikamu.
Holdback Value	Iyo yakagadziridzwa Holdback Band Kukosha inoiswa ipapo ipapo pane yazvino chikamu.

ZVINHU ZVINHU ZVINHU ZVINHU ZVINHU: PEJI 33

Parameters	Mhedzisiro pachikamu chekumhanya
Code	0 kusvika 9999 (Default: 0)
Mushandisi Linearisation	(Default: Disable)
Total Break Points	1 kusvika 32 (Default: 2)
Break Point Number	1 kusvika 32 (Default: 1)
Kukosha chaiko kweBreak Point (X kubatana)	-1999 kusvika ku9999 (Default: Undefined)
Yakatorwa Kukosha kweBreak Point (Y kubatana)	-1999 kusvika ku9999 (Default: Undefined)

TAFURA- 1

Option	Range (Min. kusvika Max.)	Resolution
J Rudzi T/C	0 kusvika +960°C / +32 kusvika +1760°F	Yakagadziriswa 1°C / 1°F
K Rudzi T/C	-200 kusvika +1376°C / -328 kusvika +2508°F
T Rudzi T/C	-200 kusvika +385°C / -328 kusvika +725°F
R Rudzi rweT/C	0 kusvika +1770°C / +32 kusvika +3218°F
S Rudzi T/C	0 kusvika +1765°C / +32 kusvika +3209°F
B Rudzi T/C	0 kusvika +1825°C / +32 kusvika +3218°F
N Rudzi T/C	0 kusvika +1300°C / +32 kusvika +2372°F
	Yakachengeterwa vatengi chaiyo Thermocouple mhando isina kunyorwa pamusoro.
RTD PT100	-199 kusvika +600°C / -328 kusvika +1112°F -199.9 kusvika kana-199.9 kusvika 999.9°F 600.0°C/	Mushandisi anogadzika 1°C / 1°F kana 0.1°C / 0.1°F
0 kusvika 20mA DC	-1999 kusvika +9999 zvikamu	Mushandisi anogadzika 1 / 0.1 / 0.01/ 0.001 zvikamu
4 kusvika 20mA DC
0 kusvika 50mV DC
0 kusvika 200mV DC
0 kusvika 1.25V DC
0 kusvika 5.0V DC
0 kusvika 10.0V DC
1 kusvika 5.0V DC

101, Diamond Industrial Estate, Navghar,
Vasai Road (E), Dist. Palghar - 401 210.
Kutengesa: 8208199048 / 8208141446
Tsigiro: 07498799226 / 08767395333
E: sales@ppiindia.net,
support@ppiindia.net
Ndira 2022

Zvinyorwa / Zvishandiso

PPI Neuro 102 EX Yakavandudza Universal Single Loop Process Controller [pdf] User Manual Neuro 102 EX Yakagadziridzwa Universal Single Loop Process Controller, Neuro 102 EX, Yakagadziridzwa Universal Single Loop Process Controller, Universal Single Loop Process Controller, Imwe Loop Process Controller, Loop Process Controller, Process Controller, Controller.

References

• User Manual