RC-100
Sensor Remote Programmer

OPERATION MIrairo

SECIFICATIONS

Magetsi	2 x AAA 1. 5V bhatiri, Alkaline inodiwa
Kutakura kesi	RC-100 mubhokisi rekutakura
Upload range	Kusvikira ku15 m (50 ft.)
Op. tembiricha	0°C∼50°C (32°F∼122°F)
Dimensions	123 x 70 x 20.3 mm (4. 84″ x 2.76″ x 0. 8″)

YAMBIRO
Bvisa mabhatiri kubva mukamuri kana kure kure kusazoshandiswa mumazuva makumi matatu.

PAKUPEDZAVIEW

Iyo remote control Wireless IR Configuration Tool chishandiso chakabatwa neruoko chekumisikidza kure kweIR-enabled fixture integrated sensors. Chishandiso chinogonesa chishandiso kuti chigadzirise kuburikidza nepushbutton isina manera kana maturusi, uye inochengeta anosvika mana sensor parameter modes kumhanyisa kumisikidzwa kweakawanda sensors.
Iyo kure kure inoshandisa bidirectional IR kutaurirana kutumira uye kugashira sensor marongero pakukwira kukwira kusvika 50 tsoka. Chishandiso chinogona kuratidza zvakambogadzikwa sensor paramita, kukopa paramita uye kutumira mitsva mitsva, kana chitoro paramende profiles. Kune mapurojekiti ayo magadzirirwo akafanana anogona kudiwa munzvimbo dzakawanda kana nzvimbo, kugona uku kunopa nzira yakagadziridzwa yekumisikidza. Zvirongwa zvinogona kukopwa munzvimbo yese kana pane akasiyana saiti.

ZVIRATIDZO zve LED

LED	DESCRIPTION	LED	DESCRIPTION
KUpenya	Yepamusoro-yekupedzisira trim inoshandura basa (Kuisa iyo inobuda nhanho yemwenje yakabatana panguva yekugara)		Kuti usarudze kukosha kwazvino kwakatenderedza lux sechikumbaridzo chemasikati. Iyi ficha inoita kuti chigadziriso chishande nemazvo mune chero mamiriro chaiwo ekushandisa.
KUNZWISISA	Kuseta iyo occupancy inonzwa kunzwa kweSensor		Iyo sensor yemasikati inomira kushanda, uye mafambiro ese akaonekwa anogona kubatidza mwenje wemwenje, zvisinei nekuti chiedza chepanyama chakajeka sei.
NGUVA YAKABATA	Iyo nguva iyo Sensor ichadzima (kana ukasarudza kumira-nedanho iri 0) kana kudzima mwenje kusvika padanho rakaderera mushure mekunge nzvimbo yabviswa.	MIRA-BY DIM	Kuisa chiyero chekubuda chemwenje wakabatana panguva yevacancy. Iyo sensor inogadzirisa kubuda kwemwenje padanho rakaiswa. Kuseta STAND-BY DIM level pa 0 zvinoreva chiedza chizere kubva du ringvacancy.
MAZUVA SENSOR	Kumiririra zvikumbaridzo zvakasiyana-siyana zvechiedza chechimiro cheSensor.	MIRA-BY NGUVA	Kumiririra nguva iyo iyo Sensor ichaita kuti mwenje urambe wakadzikama mushure mekunge KUBATA NGUVA kwapera.

BUTTON OPERATION

BUTTON	DESCRIPTION	BUTTON	DESCRIPTION
	Press the bhatani, mwenje unoenda kune zvachose on kana zvachose off mode, uye sensor yakaremara. (ZVINOFANIRA kudzvanya bhatani rekusiya iyi modhi yeSetting.		Press bhatani, iyo sensor inotanga kushanda uye ese magadzirirwo anoramba akafanana neazvino chimiro mwenje usati wadzima.
	Ratidza zvazvino / zvekupedzisira zvigadziriso zviratidzi mu LED zviratidzi (iyo ma LED zviratidzo zvichange zviripo pakuratidza marongero paramita).		Bhatani ndeyekuedza kunzwira tsitsi chete. mushure mekusarudza senitivity zvikumbaridzo, wobva wadzvanya iyo bhatani, Sensor inoenda ku test mode(kubata nguva i2s chete) otomatiki bhatani rekusiya kubva pane iyi modhi.
	Press bhatani, zvese zvigadziriso zvinodzokera kune zvigadziriso zve dip Shandura mu sensor.
	Pinda mumamiriro ekugadzika, iyo parameter LEDs ye remote control inopenya kuti isarudzwe. uye Famba uchienda UP uye Pasi kuti usarudze maparamita akasarudzwa muzviratidzo zve LED.		Enda kune LEFT uye KURUDZWA kuti usarudze maparamita akasarudzwa muzviratidzo zve LED.
	Simbisa iyo yakasarudzwa paramita yakasarudzwa parameter muremote control.		Vhura uye vhara smart masikati Sensor. Press Pinda mumamiriro ekumisikidza, parameter maLED eremote control anopenya kuti asarudzwe, Dzvanya yekuvhura kana kuvhara smart masikati Sensor.
	Press bhatani, rodha yazvino paramita kune sensor (s), iyo inotungamirwa mwenje iyo sensor inobatanidza ichaita Wolf sekusimbiswa.
	4 Scene modes ane preset paramita anowanikwa kuti achinje uye achengetedzwe mumamodhi.

KUGADZIRA

Iyo SETTING Yemukati ine ese anowanikwa marongero uye paramita kune kure sensors. Iyo inokutendera iwe kuti uchinje iripo kutonga, ma paramita, uye kushanda kwe sensor kubva kufekitori default kana zvazvino paramita.
Chinja akawanda masetirwo eiyo sensor (s)

1. Press bhatani, iyo remote control ma LEDs inoratidza ichangoburwa paramita yawakaisa.
   CHERECHEDZA: kana ukasunda bhatani pamberi, unofanira kusunda bhatani rekuvhura sensor.
2. Press pinda mune yekumisikidza mamiriro, iyo parameter maLED eremote control anopenya kuti asarudzwe, famba uchienda kune yaunoda kuseta nekudzvanya. kusarudza ma parameter matsva.
3. Dzvanya ok kuti usimbise marongero ese uye mari.
4. Tarisa pane inotarirwa sensor uye dzvanya kuti uise iyo itsva parameter, iyo inotungamira mwenje iyo sensor inosanganisirwa ichave iri / kudzima sekusimbiswa.
   CHERECHEDZA: iyo kuseta inoshanda kiyi nhanho ndeye Push, pinda mumamiriro akaiswa.
   CHERECHEDZA: iyo inotungamira mwenje iyo sensor inobatanidza ichave iri / kudzima mushure mekuwana iyo itsva parameter sekusimbiswa.
   CHERECHEDZA: Kana ukadzvanya bhatani, iyo iri kure inotungamirwa zviratidzi icharatidza iwo azvino paramita akatumirwa.

Chinja akawanda kuseta kwema sensors ane smart photocell sensor Vhura

1. Press, iyo iri kure inotungamirwa zviratidzi icharatidza yazvino paramita.
2. Dzvanya kana kupinda mumamiriro ekumisikidza, parameter Led zviratidzo zveiyo remote control inopenya kuti isarudzwe.
3. Press, 2 inotungamira zviratidzi ichapenya mumasikati sensor marongero, sarudza masikati senzvimbo yekuvheneka paOtomatiki, sarudza masikati machena senzvimbo yekudzima Otomatiki.
4. Press kusimbisa zvigadziriso zvose uye kuchengetedza.
5. Tarisa pane inotarirwa sensor uye tinya kuti uise iyo itsva parameter. Chiedza chinotungamirwa icho sensor inobatanidza chichava pa / kudzima.

CHERECHEDZA: inodzimwa nekusingaperi.

1. Vhura kana kuvhara iyo smart masikati sensor nekusundidzira kana remote control iri musetting condition.
2. Kana iyo smart yemasikati sensor ichivhura, 2 Led zviratidzo zvinopenya mumasikati ma sensor seti. sarudza masikati senzvimbo yekuvhenekera paOtomatiki, sarudza masikati se nzvimbo yekudzima yega. Kana iyo smart yemasikati sensor yakavharwa, 1 Led chiratidzo chinopenya mumasikati sensor seti yekusarudza masikati sensor chikumbaridzo.
3.  Kana iyo smart masikati sensor ichivhura, nguva yekumira ndeye chete.
4.  Smart masikati sensor inotora nzvimbo yeyakajairika photocell sensor uye inoshanda yakazvimiririra.
5. Ona Daylight Sensor Basa.

Corridor Basa

Iri basa mukati meiyo inofamba sensor kuwana matatu-level kutonga, kune dzimwe nzvimbo dzinoda
chiziviso chekuchinja chiedza usati wadzima. Iyo sensor inopa 3 mazinga echiedza: 100% -> mwenje wakadzima (mwenje wechisikigo hauna kukwana) -> kudzima; uye 2 nguva dzenguva yakasarudzwa yekumirira: nguva yekufambisa-nguva uye nguva yekumira; Selectable daylight threshold uye rusununguko rwekuona nzvimbo.
|Nechiedza chakasikwa chakakwana, mwenje haubatike kana kuvepo kwaonekwa.

Nekusakwana kwechiedza chechisikigo, sensor inodzima mwenje pachayo kana kuvepo kwaonekwa.
Mushure mekubata-nguva, mwenje unodzima kuti umire-pamwero kana mwenje wepanyama wakatenderedza uri pazasi pechikumbaridzo chemasikati.

Chiedza chinodzima otomatiki mushure mekunge nguva yekumira yadarika.

Masikati Sensor Basa
Vhura sensor yemasikati nekusundidzira kana remote control iri musetting condition.

Chiedza chinobatidza pa100% kana paine kufamba kwaonekwa.

Chiedza chinodzima kuti chimire-pamwe mushure menguva yekubata-bata.

Chiedza chinoramba chiri pamwero we dimming usiku.

Zvirongwa pakuratidzira uku: Bata-nguva: 30min setpoint kuvheneka pa:50lux setpoint kudzima:300lux Stand-by Dim: 10% Stand-by nguva: +∞ (kana yakasununguka photocell sensor, nguva yekumira inongori + ∞)

Kana mwero wemwenje wechisikigo ukapfuura setpoint kudzima, mwenje unodzima kunyangwe kana nzvimbo yagara.
Chiedza chinongobatidza pa10% kana mwenje wechisikigo usina kukwana (pasina kufamba).

Corridor Basa VS Masikati Sensor Basa.

1. Mune corridor function, batidza mwenje ZVINOFANIRA nechakasikwa mwenje nhanho yakaderera masikati sensor kuseta uye Kugara. Mune smart daylight sensor function, batidza mwenje nemwenje wechisikigo mwero wakaderera masikati seti kuti uvheneke kunyangwe paine vacancy.
2. Mucorridor function, dzima light by standby time kupera kana vacancy. Mune smart daylight sensor function, dzima mwenje neyakasikwa mwenje mwero wakakwira kupfuura masikati setpoint kuti udzime kunyangwe uchigara.
3. Mu smart daylight sensor function, yakasikwa light level yakareruka/ yakaderera pane masikati setpoint kudzima/pa INOFANIRA kuchengeta kanenge 1mintue, inozodzima/kuvheneka otomatiki.

Nezve RESET neMODE(1,2,3,4)
Iyo remote control inouya ne 4 Scene MODES iyo isingaite. Iwe unogona kugadzira maparamendi aunoda uye woachengeta seMODE itsva (1,2,3,4) kugadzirisa masensa akaiswa.
Dzorera zvakare: zvese zvigadziriso zvinodzokera kune zvigadziriso zveDIP Shandura mu sensor.

ZVIMWE ZVIRI MUKATI (1 2 3 4)

MODE	KUpenya	KUNZWISISA	NGUVA YAKABATA	DAYLIGHT SENSOR	MIRA-BY DIM	MIRA-BY NGUVA
MODE1	70%	20%	10s		0%	+∞
MODE 2	70%	20%	10s		0%	+∞
MODE 3	70%	20%	10s		0%	+∞
MODE 4	70%	20%	10s		0%	+∞

Chinja maMODE:

1. press bhatani, iyo remote control Led zviratidzo kuratidza zviripo parameters.
2. press kusarudza ma parameter matsva.
3. Press kusimbisa ese ma parameter uye chengetedza mumodhi.

UPLOAD

Basa rekurodha rinokutendera kuti ugadzirise sensor ine ese ma parameter mukuita kumwe chete. Inogona kusarudza CURRENT SETTING paramita kana iyo MODE yekurodha. Yazvino kuseta ma paramita kana iyo MODE inoratidzwa muRemote control.
Isa ma paramita azvino kune sensor (s), uye dzokorora ma sensor paramita kubva kune imwe kuenda kune imwe

1. Press bhatani kana kudzvanya ese ma parameter anoratidzwa muRemote control.
   Cherechedza: tarisa kana ese ma paramita akarurama, kana zvisiri, shandura iwo.
2. Tarisa pane sensor uye tinya iyo bhatani, mwenje unobatanidza sensor uchave wakabatidzwa / wakadzima sekusimbiswa.
   Cherechedza: kana imwe sensor ichida iwo ma paramita akafanana, ingonanga kune sensor uye wodzvanya iyo bhatani.

Zvinyorwa / Zvishandiso

HOWARD KUvheneka RC-100 Sensor Remote Programmer [pdf] Bhuku reMirayiridzo RC-100, Sensor Remote Programmer, Remote Programmer

References

• User Manual