EWeLink WSD510B Zigbee 3.0 Tembiricha uye Humidity Sensor
Mirayiridzo Yekushandiswa Kwechigadzirwa
Device Setup
Register and log in to the app. Click on the ‘+’ icon on the top right or middle of the home page to add the device.
Adding Device to Gateway
Add a new device by long-pressing the RESET key of the sensor with a pin for more than 5 seconds until the indicator light flashes quickly. Discover nearby devices and confirm.
Viewing Data
Once the temperature and humidity sensor is successfully connected to the gateway, an icon will appear on the homepage. Click on the icon to view data yekushisa uye humidity.
Connecting with Alexa Echo
After registering, add the Echo device (must support Zigbee). Switch to Devices, choose ‘+’, then Add Device, and select Thermostat. For other devices, scroll to the bottom to find Other, choose Zigbee, and discover devices automatically within 45 seconds when the device is in configuration state.
Dhawunorodha App
Download the eWeLink app from the App Store or scan the provided QR code to download.
Chinyorwa Chakakosha
The Zigbee sensor must be connected to a gateway, Alexa, or other compatible devices for use.
Ndapota verenga bhuku rino zvakanyatsonaka usati washandisa uye chengeta kuti uzvishandise mune ramangwana.
Product parameter
- Kuisa voltage: DC3V CR2032
- Static current: ≤20uA
- Kushanda ikozvino: ≤15mA
- Yakaderera voltage: ≤2.5V
- Zigbee: IEEE 802.15.4
- Detection temperature: -9.9℃~+60℃
- Detection humidity: 0-99%RH
- Installation mode: Wall mount/Place desk
- Kushanda kwekushanda: -9.9 ℃ ~ + 60 ℃
- Operating humidity: Maximum 99%RH
Cherechedza:
Do not use in humidity over 90% for a long time.
Nhanganyaya yechitarisiko
Short-press the reset button to report temperature and humidity; press the reset button twice to switch the temperature unit between Celsius and Fahrenheit; long-press the reset button for 3 seconds to enter the network configuration mode.
LCD
- Register and log-in. click “+” on the top of right corner or middle at home page to add device, choose quickly to add, click one device → input WiFi password → search device manually → choose device to connect with gateway ( gateway has to configuration success in advance )
- Click enter Gateway homepage by APP → Add devices → Add new devices→ Long press “RESET” key of sensor by a pin for more than 5 seconds until the indicator light flashes quickly → Discovering nearby devices → Confirm
- It shows a icon on homepage when the temperature humidity sensor connection success with Gateway , click icon to check datas of temperature and humidity
- Steps of connecting with Alexa echo, after registered, Echo adding success (must support Zigbee) → switch to “Devices” → choose “+” at right corner → Add Device → Choose“Thermostat” → other devices roll to bottom to find “Other” → Choose zigbee → Discover Devices → search automatically with 45 seconds when device in configuration state.
Notes:
- The sensor collects data once every minute.
- The data reporting time is every 30 minutes.
- Temperature and humidity collection: temperature 0.5°C, humidity 5%.
- Download “eWeLink” APP by APP store, or scan following QR code to download it（Zigbee sensor must be connected with gateway , Alexa or other devices to use）
Mibvunzo Inowanzo bvunzwa
Mubvunzo: Iyo sensor inogona kushandiswa mumamiriro ekunyorova kwepamusoro here?
A: It is not recommended to use the sensor in humidity over 90% for an extended period of time.
Mubvunzo: Ndinoziva sei kana sensor yakabatana negedhi zvakabudirira?
A: An icon will appear on the homepage indicating a successful connection. Click on the icon to view data yekushisa uye humidity.
Zvinyorwa / Zvishandiso
 |
EWeLink WSD510B Zigbee 3.0 Tembiricha uye Humidity Sensor [pdf] Bhuku reMirayiridzo WSD510B Zigbee 3.0 Temperature uye Humidity Sensor, WSD510B, Zigbee 3.0 Tembiricha uye Humidity Sensor, Tembiricha uye Humidity Sensor, Humidity Sensor |