Handle with Follow Focus
（for DJI RS Series）4329
Operating Instruction

• Thank you for purchasing SmallRig’s product.
• Please follow the safety warnings.
• Please read this Operating Instruction carefully.

Important Notice

• Please read this manual carefully.
• This product is not dustproof or waterproof. Please do not use it in water.
• Protect the product from falling to the ground, collision or strong impact.
• Do not apply pressure to the OLED screen. Excessive pressure will cause permanent damage.
• Do not use the product in a completely enclosed environment, as it may cause malfunction, fire or accident due to increased internal temperature.
• Do not place the product in a place of high temperature to avoid damage to the battery or battery explosion.
• Do not place the product in a place with corrosive chemicals to avoid malfunction caused by corrosion.
• Do not place the product near combustible or volatile solutions to avoid fire or smoke.
• Turn off the product after use.
• Please clean this product with a soft, dry cloth.
• This product contains built-in non-removable lithium batteries, unauthorized disassembly is strictly prohibited.
• After being stored for a long time without use, the product should be charged and discharged once in 6 months for maintenance before restoring about 60% of the charged capacity, to extend the life of the battery.
• Please do not throw away the product wilfully as its battery contains a few harmful substances. Please recycle the damaged or unused products in accordance with the waste management measures.
• When the battery icon is flashing, please charge the device immediately, otherwise the device will automatically switch off due to drained battery in about half an hour.
• Do not disassemble the product. If you suspect any problem with the product, please contact the platform where you purchased it andapply for after-sales service
• This product can only control the DJI stabilizer correctly if the slider on the left side of the DJI stabilizer is connected and the knob islocked with a wrench；
• This product is dedicated to controlling the DJI RS 2 / RS 3 Pro / RS 4 / RS 4 Pro stabilizers。

In the Box

1. Stabilizer follow focus handle × 1
2. Receiver × 1
3. USB-A to USB-C Cable × 1
4. Guarantee Card × 1

Product size

Product Introduction

1. Joystick
2. Record button
3. Mode Switching
4. Sleep Mode
5. Display
6. Trigger Button
7. Scroll Wheel
8. Sliders
9. D/S switch lever
10. QD interface
11. Cold shoe mount
12. Wrist strap hole
13. Locking knob
14. Signal indicator
15. Limit column
16. Pin
17. 1/4″-20 positioning hole

Product Features

1. Joystick: Push the joystick up and down to control the gimbal’s pitch axis movement, and push the joystick left and right to control the gimbal’s translation axis movement. Joystick calibration method: [Press the trigger button three times in a row, and keep pressing the fourth time. The calibration icon will be displayed on the screen . Then the joystick will rotate more than 6 circles at the extreme position and stop. The joystick will stay in the middle position for 20 seconds without any operation, waiting for the calibration to complete. If the calibration fails ,the calibration error will be displayed and recalibration is required. If the calibration is successful, it will not be displayed.
2. Recording / Photographing Button: This button has two strokes. Pressing it lightly (the first stroke) controls the camera to autofocus, and pressing it hard (the second stroke) controls the camera to start recording. After recording starts, the recording time is displayed. Pressing it again stops recording, and pressing it hard and long controls the camera to take photos.
3. Mode switch (M key): Single-click to switch modes, double-click to enter / exit vertical shooting mode (RS 4 /RS 4 Pro does not have this function), triple-click to enter/exit 360° rotation mode, long-press the M button to enter/release to exit sports mode, and double-click the trigger button while long-pressing M to lock (exit lock) sports mode.
4. Sleep mode: Single or double-click the power button to enter / exit sleep mode.
5. Display screen: Displays the current mode of the controller. The screen lights up to indicate a normal connection.
6. Trigger button (return to center/lock ): Single click: install DJI LiDAR focus rangefinder or Ronin image transmission and turn on, turn on or off ActiveTrack; Double click: return the gimbal to center; Triple click: enter selfie mode; Long press: lock the gimbal’s three axes; Long press the trigger button and click the M button to lock or exit the lock gimbal (lock without pressing the trigger button).
7. Scroll wheel: The default function is to control focus/zoom by wire. You can change the settings on the touch screen of the DJI RS 2 / RS 3 Pro / RS 4 / RS 4 Pro stabilizer. You can set it to focus motor, control focus/zoom by wire, adjust the camera ISO, aperture, shutter speed, and control the roll axis, pan axis or pitch axis. You can change the corresponding scroll wheel speed, smoothness, and forward and reverse direction according to the settings on the touch screen;
8. Slider: The side slider can be used to expand focus wheels, mobile phone holders, monitors and other equipment.
9. D/S switch lever: used to switch and control DJI or Smallrig focus motor 4297
10. QD interface: There is a QD interface on the right slider, which can be used to connect the stabilizer shoulder strap 4118.
11. Cold shoe mount: 2905B can be used to connect a 5-inch monitor. The interface can only bear 1kg and cannot be overloaded.
12. Wrist strap hole: PAC2456B can be used to make holding more comfortable and safer.
13. Locking knob: After loosening the knob, control the angle of the handle.
14. Signal indicator light: used to indicate whether it is working properly, the blue light indicates normal communication, and the red light indicates no connection.
15. Limit column: The limit column must correspond to the Nato interface on the DJI stabilizer, otherwise the stabilizer cannot be controlled.
16. Pin: Do not be too violent during disassembly or assembly, otherwise the Pin interface will be damaged.

Icon Indication

① ：Mode indication,“”is displayed when the stabilizer goes into sleep mode.
② “”For Battery indication, and the battery display bar flashes when charging; the icon flashes when the power is ≤10%;
③ “” Zigbee icon, which flashes to indicate it is not connected to the remote control;
④ “”Current channel of the remote control module, range 00 ~ 15;
⑤ “”360 degree rotation mode
⑥ “” Lock mode
⑦ “”,“”Display“”in joystick calibration, display “” after calibration failure when operating joystick.
⑧ “” Power Icon

Product Use

1. The receiver must be locked at the location with metal contacts on the stabilizer.
2. After connecting the receiver, long press the power button on the handle, and the blue light on the receiver will be on and you can use it.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

To assure continued compliance, any changes or modifications not expressly approved by the party.
Responsible for compliance could void the user’s authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices).
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
RF warning statement:
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.

ISED Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Specifications

*Compatibility：DJI RS 2 / DJI RS 3 Pro / DJI RS 4 / DJI RS 4 Pro

WE ARE HERE FOR YOU

https://global.smallrig.com/support

ETICHETTATURA AMBIENTALE
ENVIRONMENTAL LABELING

https://global.smallrig.com/packaging_material/

GAVIMOSA CONSULTORIA, SOCIEDAD LIMITADA,
CASTELLANA 9144, 28046 Madrid, compliance.gavimosa@outlook.com
Sea&Mew Accounting Ltd,
Electric Avenue Vision 25, London, Enfield EN3 7GD, info@seamew.net

Manufacturer Email: support@smallrig.com
Manufacturer: Shenzhen Leqi Innovation Co., Ltd.
Add: Rooms 101, 701, 901, Building 4, Gonglianfuji Innovation Park, No. 58, Ping’an Road, Dafu Community, Guanlan Street, Longhua District, Shenzhen, Guangdong, China.
Consignor: Shenzhen LC Co., Ltd.
Add: Room 201, Building 4, Gonglianfuji Innovation Park, No. 58, Ping’an Road, Dafu Community, Guanlan Street, Longhua District, Shenzhen, Guangdong, China.

– FREE YOUR DREAM –

Documents / Resources

SmallRig RS Series Handle with Follow Focus [pdf] Instruction Manual DJI RS 4329, RS Series Handle with Follow Focus, RS Series, Handle with Follow Focus, Follow Focus, Focus

References

• User Manual