SmallRig 4329 Handle with Follow Focus Instruction Manual

The Handle with Follow Focus for DJI RS Series, model DJI RS
4329, is designed to enhance control and functionality when using
DJI RS stabilizers. It features various buttons and controls for
camera operation, including autofocus, recording, and mode
switching. The product also includes indicators for signal and
power status, as well as interfaces for accessories like monitors
and shoulder straps.

Product Usage Instructions

Receiver Installation:
- Ensure the receiver is securely locked at the location with
  metal contacts on the stabilizer.

Power On:
- After connecting the receiver, long press the power button on
  the handle until the blue light on the receiver turns on,
  indicating it is ready for use.

FCC & ISED Statements

This device complies with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s) and operates under the
following conditions:

This device must not cause interference.

This device must accept any interference that may affect its
operation.

FAQ

Q: How do I know if the device is ready for use?

A: When the blue light on the receiver is on after pressing the
power button, it indicates that the device is ready for
operation.

Q: What is the purpose of the QD interface?

A: The QD interface on the right slider is used to connect the
stabilizer shoulder strap for added convenience during use.

“`

View Fullscreen

v0.0

20241105

: 75*105mm

Handle with Follow Focus for DJI RS Series
DJI RS 4329
Operating Instruction /
Handle with Follow Focus for DJI RS Series
DJI RS 4329
Operating Instruction /

· Thank you for purchasing SmallRig’s product. · Please read this Operating Instruction carefully. · Please follow the safety warnings.
Important Notice
Please read this manual carefully. This product is not dustproof or waterproof. Please do not use it in water. Protect the product from falling to the ground, collision or strong impact. Do not apply pressure to the OLED screen. Excessive pressure will cause permanent damage. Do not use the product in a completely enclosed environment, as it may cause malfunction, fire or accident due to increased internal temperature. Do not place the product in a place of high temperature to avoid damage to the battery or battery explosion. Do not place the product in a place with corrosive chemicals to avoid malfunction caused by corrosion. Do not place the product near combustible or volatile solutions to avoid fire or smoke. Turn off the product after use. Please clean this product with a soft, dry cloth. This product contains built-in non-removable lithium batteries, unauthorized disassembly is strictly prohibited. After being stored for a long time without use, the product should be charged and discharged once in 6 months for maintenance before restoring about 60% of the charged capacity, to extend the life of the battery. Please do not throw away the product wilfully as its battery contains a few harmful substances. Please recycle the damaged or unused products in accordance with the waste management measures. When the battery icon is flashing, please charge the device immediately, otherwise the device will automatically switch off due to drained battery in about half an hour.
· Do not disassemble the product. If you suspect any problem with the product, please contact the platform where you purchased it andapply for after-sales service · This product can only control the DJI stabilizer correctly if the slider on the left side of the DJI stabilizer is connected and the knob islocked with a wrench · This product is dedicated to controlling the DJI RS 2 / RS 3 Pro / RS 4 / RS 4 Pro stabilizersb

In the Box
1. Stabilizer follow focus handle × 1
3. USB-A to USB-C Cable × 1

46.50

66.31

700.0 15 16

153.50 36.00

2. Receiver

× 1

4. Guarantee Card × 1

26.00

49.40

6 9 17

13
8 1
2 7
3

11
5 10
4

1. Joystick

7. Scroll Wheel

13. Locking knob

2. Record button 8. Sliders

14. Signal indicator

3. Mode Switching 9. D/S switch lever 15. Limit column

4. Sleep Mode

10. QD interface

16. Pin

5. Display

11. Cold shoe mount 17. 1/4″-20 positioning hole

6. Trigger Button 12. Wrist strap hole

1.Joystick: Push the joystick up and down to control the gimbal’s pitch axis movement, and push the joystick left and right to control the gimbal’s translation axis movement. Joystick calibration method: [Press the trigger button three times in a row, and keep pressing the fourth time. The calibration icon will be displayed on the screen . Then the joystick will rotate more than 6 circles at the extreme position and stop. The joystick will stay in the middle position for 20 seconds without any operation, waiting for the calibration to complete. If the calibration fails ,the calibration error will be displayed and recalibration is required. If the calibration is successful, it will not be displayed.
2.Recording / Photographing Button: This button has two strokes. Pressing it lightly (the first stroke) controls the camera to autofocus, and pressing it hard (the second stroke) controls the camera to start recording. After recording starts, the recording time is displayed. Pressing it again stops recording, and pressing it hard and long controls the camera to take photos.
3.Mode switch (M key): Single-click to switch modes, double-click to enter / exit vertical shooting mode (RS 4 /RS 4 Pro does not have this function), triple-click to enter/exit 360° rotation mode, long-press the M button to enter/release to exit sports mode, and double-click the trigger button while long-pressing M to lock (exit lock) sports mode.
4.Sleep mode: Single or double-click the power button to enter / exit sleep mode. 5.Display screen: Displays the current mode of the controller. The screen lights up
to indicate a normal connection. 6.Trigger button (return to center/lock ): Single click: install DJI LiDAR focus
rangefinder or Ronin image transmission and turn on, turn on or off ActiveTrack; Double click: return the gimbal to center; Triple click: enter selfie mode; Long press: lock the gimbal’s three axes; Long press the trigger button and click the M button to lock or exit the lock gimbal (lock without pressing the trigger button). 7.Scroll wheel: The default function is to control focus/zoom by wire. You can change the settings on the touch screen of the DJI RS 2 / RS 3 Pro / RS 4 / RS 4 Pro stabilizer. You can set it to focus motor, control focus/zoom by wire, adjust the camera ISO, aperture, shutter speed, and control the roll axis, pan axis or pitch axis. You can change the corresponding scroll wheel speed, smoothness, and forward and reverse direction according to the settings on the touch screen; 8.Slider: The side slider can be used to expand focus wheels, mobile phone holders, monitors and other equipment. 9.D/S switch lever: used to switch and control DJI or Smallrig focus motor 4297

10.QD interface: There is a QD interface on the right slider, which can be used to connect the stabilizer shoulder strap 4118.
11.Cold shoe mount: 2905B can be used to connect a 5-inch monitor. The interface can only bear 1kg and cannot be overloaded.
12.Wrist strap hole: PAC2456B can be used to make holding more comfortable and safer.
13.Locking knob: After loosening the knob, control the angle of the handle. 14.Signal indicator light: used to indicate whether it is working properly, the blue
light indicates normal communication, and the red light indicates no connection. 15.Limit column: The limit column must correspond to the Nato interface on the
DJI stabilizer, otherwise the stabilizer cannot be controlled. 16.Pin: Do not be too violent during disassembly or assembly, otherwise the Pin
interface will be damaged.

. . . ” “,” “,” “Mode indication,” “is displayed when the stabilizer goes into
sleep mode. ” “For Battery indication, and the battery display bar flashes when charging; the
icon flashes when the power is 10%; ” ” Zigbee icon, which flashes to indicate it is not connected to the remote control; ” “Current channel of the remote control module, range 00 ~ 15; ” “360 degree rotation mode ” ” Lock mode ” “,” “Display” “in joystick calibration, display ” ” after calibration failure
when operating joystick. ” ” Power Icon

Product Use
1. The receiver must be locked at the location with metal contacts on the stabilizer.
2. After connecting the receiver, long press the power button on the handle, and the blue light on the receiver will be on and you can use it.

FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party. Responsible for compliance could void the user’s authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices). This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. RF warning statement: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
ISED Statement
English: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).Operation is subject to the following two conditions: (1)This device may not cause interference. (2)This device must accept any interference, including interference that may cause undesired operation of the device.

French:Cet appareil contient des émetteurs/récepteurs exempts de licence qui sont conformes aux CNR exempts de licence d’Innovation, Sciences et Développement économique Canada. Le fonctionnement est soumis aux deux conditions suivantes : (1) Cet appareil ne doit pas causer d’interférences. (2) Cet appareil doit accepter toute interférence, y compris les interférences susceptibles de provoquer un fonctionnement indésirable de l’appareil. This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.cet appareil est conforme à l’exemption des limites d’évaluation courante dans la section 2.5 du cnr – 102 et conformité avec rss 102 de l’exposition aux rf, les utilisateurs peuvent obtenir des données canadiennes sur l’exposition aux champs rf et la conformité. This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment.This equipment should be installed and operated with minimum distance 0cm between the radiator & your body. Cet équipement doit être installé et utilisé avec une distance minimale de 0cm entre le radiateur et votre corps. Cet équipement est conforme Canada limites d’exposition aux radiations dans un environnement non contrôlé.
Specifications

Product Dimensions Product weight Material(s) Recommended charging environment temperature Rated power Maximum allowable input current Allowable input voltage range

7.5 × 1.8 × 1.8in 9.2 ± 0.2oz
Aluminum alloyPlastic rubber Stainless steel
5 40 0.5W 1A
5V 7V

WE ARE HERE FOR YOU ETICHETTATURA AMBIENTALE

ENVIRONMENTAL LABELING

GAVIMOSA CONSULTORIA, SOCIEDAD LIMITADA, EC REP CASTELLANA 9144, 28046 Madrid,
compliance.gavimosa@outlook.com
Sea&Mew Accounting Ltd, UK REP Electric Avenue Vision 25, London, Enfield EN3 7GD,
info@seamew.net
Manufacturer: Shenzhen Leqi Innovation Co., Ltd. Add: Rooms 103, 501 and 601, Building 5, Fenghe Industrial Park, Nos. 1301-50 Guanguang Road, Longhua District, Shenzhen, Guangdong, China.
Consignor: Shenzhen LC Co., Ltd. Add: Rooms 602, Building 5, Fenghe Industrial Park, No. 1301-50 Guanguang Road, Xinlan Community, Guanlan Street, Longhua District, Shenzhen, Guangdong, China.

GB4943.1-2022 FCC ID:XXXXXXX

CMIIT ID:XXXXXXXX

FR Boîte 1 Papier 5

USB-A to USB-C Cable

· SmallRig ·
·

OLED , ,, 6 60%
·
· DJI DJI
· DJI RS 2 / RS 3 Pro / RS 4 / RS 4 Pro

× 1

3. USB-A to USB-C × 1

46.50

66.31

700.0 15 16

153.50 36.00

2. × 1 4. × 1
26.00
49.40

6 9 17

13
8 1
2 7
3

11
5 10
4

9. D/S 10. QD

13.

14.

17. 1/4″-20

3. 7. 11. 15.

4. 8. 12. 16. Pin

1. ” ” 620 ” ”
2./
3.(M)/(RS 4 /RS 4 Pro)
/360°M/M () 4./ 5. 6.(/)DJI LiDARRonin M() 7./DJI RS 2 / RS 3 Pro / RS 4 / RS 4 Pro /ISO 8. 9.D/SDJISmallrig4297 10.QDQD4118 11.2905B51kg 12.PAC2456B 13. 14.14. 15.Nato 16.PinPin

” . “”, . “”, . “” ”

”

“10%

” “Zigbee

” “00 ~ 15

” “360

” ”

” “”, “” “” ”

” ”

1. 2.

190 × 46 × 66mm 263 ± 5g 5 40 0.5W 1A 5V 7V

1301-50 5 103501601

: 1301-50 5 602

GB4943.1-2022 FCC ID:XXXXXXX

CMIIT ID:XXXXXXXX

FR Boîte 1 Papier 5

– FREE YOUR DREAM –

1.RoHS 2.0 2.
-20±2 24h 70±2 90%±5% 24h 3. 4. 5.±1mm±10mm 6.

1/1

±1

MODEL (
PART_NO.
PART_NAME

4329

Documents / Resources

SmallRig 4329 Handle with Follow Focus [pdf] Instruction Manual
2BC2U-4329, 2BC2U4329, 4329 Handle with Follow Focus, 4329, Handle with Follow Focus, Follow Focus, Focus, Handle

References

User Manual

4329 Handle with Follow Focus

Specifications

Product Information