SmallRig 4329 Handle with Follow Focus for DJI RS Series

Important Notice

Thank you for purchasing SmallRig's product. Please read this Operating Instruction carefully and follow all safety warnings.

• Please read this manual carefully.
• This product is not dustproof or waterproof. Do not use it in water.
• Protect the product from falling to the ground, collision, or strong impact.
• Do not apply pressure to the OLED screen; excessive pressure will cause permanent damage.
• Do not use the product in a completely enclosed environment, as it may cause malfunction, fire, or accident due to increased internal temperature.
• Do not place the product in a high-temperature location to avoid damage to the battery or battery explosion.
• Do not place the product in a location with corrosive chemicals to avoid malfunction caused by corrosion.
• Do not place the product near combustible or volatile solutions to avoid fire or smoke.
• Turn off the product after use.
• Please clean this product with a soft, dry cloth.
• This product contains built-in non-removable lithium batteries; unauthorized disassembly is strictly prohibited.
• After long-term storage without use, the product should be charged and discharged once every 6 months for maintenance, restoring about 60% of the charged capacity to extend battery life.
• Please do not discard the product arbitrarily, as its battery contains harmful substances. Recycle damaged or unused products according to waste management measures.
• When the battery icon is flashing, please charge the device immediately. The device will automatically switch off due to drained battery in about half an hour.
• Do not disassemble the product. If you suspect any problem, contact the platform where you purchased it for after-sales service.
• This product can only control the DJI stabilizer correctly if the slider on the left side of the DJI stabilizer is connected and the knob is locked with a wrench.
• This product is dedicated to controlling the DJI RS 2 / RS 3 Pro / RS 4 / RS 4 Pro stabilizers.

In the Box

• 1. Stabilizer follow focus handle
• 2. Receiver
• 3. USB-A to USB-C Cable
• 4. Guarantee Card

Product Features

• 1. Joystick: Controls gimbal pitch and translation axis movement. Calibration is possible by pressing the trigger button four times consecutively.
• 2. Record button: First stroke for autofocus, second stroke to start/stop recording. Long press for photos.
• 3. Mode Switching (M key): Single-click to switch modes. Double-click for vertical shooting mode (not for RS 4 / RS 4 Pro). Triple-click for 360° rotation mode. Long press to enter/exit sports mode. Double-click trigger while long-pressing M to lock/unlock sports mode.
• 4. Sleep Mode: Single or double-click the power button to enter/exit sleep mode.
• 5. Display screen: Shows current controller mode. Screen lights up for normal connection.
• 6. Trigger button: Single click for ActiveTrack (with DJI LiDAR or image transmission). Double click to return gimbal to center. Triple click for selfie mode. Long press to lock gimbal axes. Long press trigger and click M to lock/exit gimbal lock.
• 7. Scroll Wheel: Default function is wire-controlled focus/zoom. Settings can be changed on the DJI stabilizer's touch screen to control focus motor, ISO, aperture, shutter speed, or roll, pan, pitch axes. Speed, smoothness, and direction are adjustable.
• 8. Slider: Side slider for expanding accessories like focus wheels or phone holders.
• 9. D/S switch lever: Switches and controls DJI or SmallRig focus motors (e.g., 4297).
• 10. QD interface: Connects to stabilizer shoulder strap (e.g., 4118).
• 11. Cold shoe mount: For connecting accessories like a 5-inch monitor (max 1kg load).
• 12. Wrist strap hole: For attaching a wrist strap (e.g., PAC2456B) for comfortable and safe handling.
• 13. Locking knob: Controls handle angle after loosening.
• 14. Signal indicator light: Blue light indicates normal communication; red light indicates no connection.
• 15. Limit column: Must align with the Nato interface on the DJI stabilizer for control.
• 16. Pin: Handle with care during disassembly/assembly to avoid damaging the Pin interface.

Product Use

1. The receiver must be locked at the location with metal contacts on the stabilizer.
2. After connecting the receiver, long press the power button on the handle. The blue light on the receiver will turn on, indicating it is ready for use.

Display Information

• Mode indication: Displays when the stabilizer enters sleep mode.
• Battery indication: Battery display bar flashes when charging. The icon flashes when power is at 10%.
• Zigbee icon: Flashes to indicate it is not connected to the remote control.
• Current channel: Displays the remote control module's channel (range 00-15).
• 360 degree rotation mode: Indicated on the display.
• Lock mode: Indicated on the display.
• Calibration status: Displays "Joystick calibration in progress" during joystick calibration, and "Calibration failure" after calibration failure.

Specifications

Regulatory Information

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example: use only shielded interface cables when connecting to computer or peripheral devices). This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

RF warning statement: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

ISED Statement (Canada)

English: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure. Users can obtain Canadian information on RF exposure and compliance. This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator & your body.

French: Cet appareil contient des émetteurs/récepteurs exempts de licence qui sont conformes aux CNR exempts de licence d'Innovation, Sciences et Développement Économique Canada. Le fonctionnement est soumis aux deux conditions suivantes : (1) Cet appareil ne doit pas causer d'interférences. (2) Cet appareil doit accepter toute interférence, y compris les interférences susceptibles de provoquer un fonctionnement indésirable de l'appareil.

Cet équipement est conforme aux limites d'exposition aux radiations du Canada établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 0cm entre le radiateur et votre corps.

Manufacturer Information

Manufacturer: Shenzhen Leqi Innovation Co., Ltd.

Address: Rooms 103, 501 and 601, Building 5, Fenghe Industrial Park, Nos. 1301-50 Guanguang Road, Longhua District, Shenzhen, Guangdong, China.

Consignor: Shenzhen LC Co., Ltd.

Address: Rooms 602, Building 5, Fenghe Industrial Park, No. 1301-50 Guanguang Road, Xinlan Community, Guanlan Street, Longhua District, Shenzhen, Guangdong, China.

EU Representative: GAVIMOSA CONSULTORIA, SOCIEDAD LIMITADA, EC REP CASTELLANA 9144, 28046 Madrid, compliance.gavimosa@outlook.com

UK Representative: Sea&Mew Accounting Ltd, Electric Avenue Vision 25, London, Enfield EN3 7GD, info@seamew.net

Certifications: ROHS, CE, FC