K GALUEGA SM3 fa'atasi ma le Module
Fa'amatalaga o oloa
O le SM3 + Module R1.5 o se matagaluega e faʻavae i luga o le MegaSquirt 3 ma le pinout o le KdFi1.4 modules. Ua mamanuina ina ia fetaui i tua ma MS2 KdFi1.4 tagata faaaoga ma laupapa. O le module e 100% AEC-Q100 faʻamaonia ma e aofia ai le faʻatinoga o le Wideband Lambda Controller ma le Bosch LSU 4.9 sensor.
O le afifi e aofia ai mea nei:
- SM3 + Module ma / poʻo le PCB faaopoopo
- Poloka USB
- Fa'aoga tusi lesona
- So'oga Molex, mea fa'apipi'i & fa'aulu solder
Fa'atonuga o le Fa'aaogaina o Mea
Taulaga USB
O le taulaga USB o le SM3 + Module ua faʻapipiʻiina i le 8kV ESD puipuiga mo VBUS ma laina Faʻamatalaga. O le USB chip e fa'aola USB, lea e fa'afaigofie ai le amio amata. So'o se uaea USB masani e mafai ona fa'aoga e fai ma uaea feso'ota'iga, e sili atu i le FERRIT core e aloese ai mai le fa'aosoina o le ESD.
Feso'ota'iga Fa'aeletise
O feso'ota'iga eletise uma e tatau ona muamua i se fuse e fa'atatau i le vaega uaea. E tatau ona fa'aoga ituaiga uaea fautuaina.
Fuse
E fautuaina le fuse 3A mo le puipuia o le SM3 + Module. O loʻo i ai foʻi i le komiti se faʻaogaina otometi 5A PTCC fuse o le a toe faʻafoʻiina o ia lava pe a maeʻa ona faʻamalo pe foia se faʻafitauli poʻo se taʻavale puʻupuʻu.
Fuafuaga LED i luga ole laupapa
O le SM3 + Module e tele i luga ole laiga LED ma galuega eseese. O fa'amatalaga nei:
| Fa'ailoga LED | Lanu | Galuega |
|---|---|---|
| LD2 | LANU MOLI | 5V eletise sapalai |
| LD3 | LANU MOLI | O2 fa'atonu fa'atalitali emo/malosi malosi |
| LD4 | LANU MOLI | O2 fa'avevela fa'avevela 2Hz/fua emo 1Hz |
| LD5 | LANU MOLI | USB Fa'amatalaga fa'amaumauga |
| LD6 | LANU MOLI | Fa'amumu pulusi A |
| LDA | LANU MOLI | Fa'amumu fatu B |
| LDB | LANU MOLI | Fa'amumu fatu C |
| LDC | LANU MOLI | Fa'amumu fatu D |
| LDD | LANU MOLI | Fa'amumu fatu E |
| LDE | LANU MOLI | Fa'amumu fatu F |
I luga ole va'a O2 Pule LED Galuega
O le O2 pule i luga ole laiga e iai fo'i galuega fa'atino. O fa'amatalaga nei:
| Tulaga Lula | Galuega |
|---|---|
| Emo vave | Tulaga fa'amafanafana |
| Faʻapipiʻi faʻapipiʻi | Tulaga fua fa'atino |
| Emo lemu | Tu'u ma/po'o tulaga sese |
Pinouts KdFi
O le SM3 + Module e iai pine eseese mo KdFi. O fa'amatalaga nei:
| KdFi Pin Fa'ailoga | I-/Gofuafua | Galuega |
|---|---|---|
| A1 | Ulufale | Tu'u fa'amumu 1 |
| B1 | Ulufale | Tu'u fa'amumu 2 |
| C1 | Ulufale | Tu'u fa'amumu 3 |
| D1 | Ulufale | Tu'u fa'amumu 4 |
| E1 | Ulufale | Tu'u fa'amumu 5 |
| F1 | Ulufale | Tu'u fa'amumu 6 |
| INJ1 – INJ6 | Tuuina atu | Valau tui 1-6 |
| 12v | Ulufale | Sao Voltage 8-16V |
| GND | Ulufale | Sao Voltage GND |
| FP | Tuuina atu | Fa'ata'ita'i Pamu Suau'u |
| FDLC | Tuuina atu | Fa'atonu pule 3-pin – TAPI |
| FDLO | Tuuina atu | Fa'atonu fa'atonu 3-pin – TALA |
| RPM1 | Ulufale | Fa'aoso fa'aoga GND |
| RPM2 | Ulufale | fa'aoga VR Fa'aoso fa'aoso |
| IAC1 – IAC2 | Tuuina atu | Galuega Lautele 1 ma le 2 (max 2A) |
| EA | Ulufale | Su'e le vevela o le ea |
| CLT | Ulufale | Coolant Temp sensor fa'aoga |
| TPS | Ulufale | Fa'ailoga Fa'ailoga Tulaga |
| OXY – OXY_2 | Ulufale | Lambda sensor signal bank 1 ma le faletupe 2 |
SM3 + Module R1.5 User Manual Kperformance
SM3+ Tusitaiala a le tagata
Polokalama, aveta'avale ma fa'amatalaga lata mai e mafai ona la'u mai ile www.Kperformance.be
Folasaga
Fa'afetai mo le fa'atauina o le SM3+. O le taamilosaga e faʻavae i luga o le MegaSquirt 3 ma le pinout o le KdFi1.4 modules. Fa'aoga le SM3 i tua ma fa'aoga MS2 KdFi1.4 ma laupapa. Na fa'amamaina ma fausia 100% AEC-Q100 fa'amalieina. O le KPerformance Wideband Lambda Controller o se vaega foi o le komiti SM3. O le Bosch LSU 4.9 sensor e mafai ona feso'ota'i sa'o e aunoa ma se fa'atonu fa'aopoopo.
E aofia i le Tiliva
- SM3 + Module ma / poʻo le PCB faaopoopo
- Poloka USB*
- Fa'aoga tusi lesona
- So'oga Molex, mea fa'apipi'i & fa'aulu solder
Polokalama
Polokalama fa'alogo fa'apitoa TUNERSTUDIO ma/po'o Megalog viewer
Avetaavale USB
O le va'a FTDI i luga ole va'a fa'atusa se feso'ota'iga RS232:
TunerStudio - Feso'ota'iga - Fa'atonu: USB ma le uaea (na'o le Tusi resitala), Auto, 115200 Baud
Taulaga USB
O le taulaga USB o le SM3 ua faʻapipiʻiina i le 8kV ESD puipuiga o VBUS ma laina Faʻamaumauga. O le pusi faʻamatalaga ma le puipuiga o le ESD o le "USB powered". Ole mea lea e fa'afaigofieina ai le amio amata pe a toe amata le afi, e le mafai e le PC ona siiina le avetaavale USB i taimi uma. O le pusi USB e fetaui i lalo, e mafai ona fa'aoga uma i le USB 3.0, 2.0 ma le 1. E mafai ona fa'aogaina uaea USB ta'itasi e fai ma uaea feso'ota'iga, ae sili atu i le FERRIT autu e aloese ai mai tui ESD.
Feso'ota'iga eletise
E pei o isi voltago vaega tu'uina atu - e tatau ona muamua i se fuse o lo'o galue i le vaega uaea.
Tulaga uaea fautuaina:
- Fa'amumu: min 1.5 mm²
- Tuiina: min 1.5 mm²
- VR sensor: min 0.5 mm²
- Talipupuni Sensors: min 0.35 mm²
- Isi: min 0.35 mm²
Fuse
Fautuaina le fa'aogaina o le fuse 3A mo le puipuia o le SM3. O loʻo tuʻufaʻatasia se fuse 5A PTCC faʻapitoa i luga o le laupapa. O le a toe setiina ia lava pe a maeʻa le malulu / foia le mataupu poʻo le taʻavale puʻupuʻu.
I luga o le laupapa galuega tauave LED
| LED
Fa'ailoga |
Lanu | Galuega |
| LD2 | LANU MOLI | 5V eletise sapalai |
| LD3 | LANU MOLI | O2 fa'atonu fa'atalitali emo/malosi malosi |
| LD4 | LANU MOLI | O2 fa'avevela fa'avevela 2Hz/fuaina emo 1hz |
| LD5 | LANU MOLI | USB Fa'amatalaga fa'amaumauga |
| LD6 | LANU MOLI | USB Fa'amatalaga fa'amaumauga |
| LDA | LANU MOLI | Fa'amumu pulusi A |
| LDB | LANU MOLI | Fa'amumu fatu B |
| LDC | LANU MOLI | Fa'amumu fatu C |
| LDD | LANU MOLI | Fa'amumu fatu D |
| LDE | LANU MOLI | Fa'amumu fatu E |
| LDF | LANU MOLI | Fa'amumu fatu F |
I luga ole va'a O2 ta'ita'i galuega fa'atino LED
| LED | Tulaga | Galuega |
| STS | Emo vave | Tulaga fa'amafanafana |
| Pwr | Malosi | |
| STS | Emo lemu | Tulaga fua fa'atino |
| Pwr | Malosi | |
| STS | Fa emoemo | Tu'u ma/po'o tulaga sese |
| Pwr | Fa emoemo |
Pinouts
| KdFi Pin Fa'ailoga I totonu-/Aluega Galuega | ||
| A1 | IGN gaosiga | Tu'u fa'amumu 1 |
| B1 | IGN gaosiga | Tu'u fa'amumu 2 |
| C1 | IGN gaosiga | Tu'u fa'amumu 3 |
| D1 | IGN gaosiga | Tu'u fa'amumu 4 |
| E1 | IGN gaosiga | Tu'u fa'amumu 5 |
| F1 | IGN gaosiga | Tu'u fa'amumu 6 |
| INJ1 | INJ galuega faatino | Valau tui 1 |
| INJ2 | INJ galuega faatino | Valau tui 2 |
| INJ3 | INJ galuega faatino | Valau tui 3 |
| INJ4 | INJ galuega faatino | Valau tui 4 |
| INJ5 | INJ galuega faatino | Valau tui 5 |
| INJ6 | INJ galuega faatino | Valau tui 6 |
| 12v | Malosiaga tuu | Sao Voltage 8-16V |
| GND | Malosiaga Ulufale | Sao Voltage GND |
| FP | Pum Suauu | Fa'ata'ita'i Pamu Suau'u |
| FDLC | Fidle Valve Output | Fa'atonu pule 3-pin
-TATAU |
| FDLO | Fidle Valve Output | Fa'atonu pule 3-pin
-TATAU |
| RPM1 | Faʻaoso le sao | Ulufale saoasaoa Crankshaft |
| GND_RPM | GND VR fa'aoga | Fa'asao saosaoa eleele |
| RPM2 | Faʻaoso le sao | Tu'u saosaoa camshaft |
| IAC1 | Galuega Lautele | Tulaga Lautele 1 max2A |
| IAC2 | Galuega Lautele | Tulaga Lautele 2 max2A |
| EA | Fa'aulufale fa'alogo | Su'e le vevela o le ea |
| CLT | Fa'aulufale fa'alogo | Coolant Temp sensor fa'aoga |
| TPS | Fa'aulufale fa'alogo | Fa'ailoga Fa'ailoga Tulaga |
| OXY | Ulufale | Lambda sensor faailo
faletupe 1 |
| OXY_2 | Ulufale | Lambda sensor faailo
faletupe 2 |
| LSU ULI | O2 Sensor fa'aoga | Bosch LSU BLACK |
| LSU samasama | O2 Sensor fa'aoga | Bosch LSU samasama |
| LSU mūmū | O2 Sensor fa'aoga | Bosch LSU mūmū |
| LSU GREY | O2 Sensor Faamafanafana | Bosch LSU GREY |
| LSU PA'E | O2 Sensor Faamafanafana | Bosch LSU PA'E |
| LSU MATUA | O2 Sensor fa'aoga | Bosch LSU lanumeamata |
| 5V | Sapalai Sensor | 5V Malosiaga Tuuina atu |
| TBL | Ulufale | Suiga laulau |
| Fa'aopoopo P1 feso'ota'iga pinout SM3 (silasila i le ata itulau7) | ||
| EGT+ | K-ituaiga Ulufale | EGT masini fa'aoga + |
| AIN1/Filifili | Faʻaaoga Analogi | Fa'aoga analog lautele |
| AIN2/JS12 | Faʻaaoga Analogi | Fa'aoga analog lautele |
| PP1 | Faʻaaoga Analogi | Fa'aoga analog lautele |
| PT4 | Pin ole PPU | !!!PPU sa'o pine!!! |
| DIN1/NitroIN | Initaneti | NitroIn fa'aoga |
| AIN0/ExtMap | Faʻaaoga Analogi | Fa'aoga analog lautele |
| DIN6/PT6/Fa'amatalaga g i totonu | Ulufale faafuainumera | Fa'aigoa fa'akomepiuta amata fa'aoga |
| PT1 | Pin ole PPU | !!!PPU sa'o pine!!! |
| DIN4/Tatala | Ulufale faafuainumera | Fa'aoga fa'afuainumera fa'alauiloa |
| GPO4/Fa'aoso | Galuega Lautele | Galuega Fa'apolokalameina 1A |
| GPO2/Nitro2 | Galuega Lautele | Galuega Fa'apolokalameina 2A |
| GPO7/VVT | Galuega Lautele | Galuega Fa'apolokalameina 2A |
| GPO5/Tacho | Galuega Lautele | Galuega Fa'apolokalameina 2A |
| GPO8/Ile | Galuega Lautele | Galuega Fa'apolokalameina 2A |
| GPO3/Nitro | Galuega Lautele | Galuega Fa'apolokalameina 2A |
| PK7 | Pin ole PPU | !!!PPU sa'o pine!!! |
| AIN3/AD7 | Faʻaaoga Analogi | Fa'aoga analog lautele |
| PT3 | Pin ole PPU | !!!PPU sa'o pine!!! |
| Tu'itu'i1 | Tu'itu'i Ulufale | Tu'itu'i Sensor Input1 |
| Tu'itu'i2 | Tu'itu'i Ulufale | Tu'itu'i Sensor Input2 |
| PP0 | Pin ole PPU | !!!PPU sa'o pine!!! |
| PT5 | Pin ole PPU | !!!PPU sa'o pine!!! |
| EGT- | K-ituaiga Ulufale | EGT sensor fa'aoga- |
Fuaina ole Saosaoa ole afi
Fa'amolemole fa'aoga le DIP ki (Retro-Fit KdFi v1.4 laupapa) e filifili ai le ituaiga mea e te mana'omia.
Suiga 1 ma le 2 e mo le mea muamua e mafai ona avea ma faailo CAM faʻataʻitaʻiga i le tufatufaina pe afai e leai sau Cranksignal.
Su'e 3 ma le 4 e mo le fa'aoga lona lua pe afai e te fa'aogaina le fa'aoga (1) ma le cam (2). Fa'amolemole aua ne'i fa'agaoioi le VR ma le HALL mo le fa'alogo tasi i le taimi e tasi. O le a le aoga lea.
- VR Sensor O le fuaina e ala i le VR sensor o le auala sili ona taatele i Europa mo afi taʻavale. O le AC voltage fa'aosoina i le vili o le VR sensor e se uili fa'aoso ma le 60-2 po'o le 36-1 nifo.
- E ono mana'omia e le fa'alogo a le HALL se tete'e toso i luga o le 1k i le 10k ohm i le va o fa'ailo i fafo ma le +5V.
Potentiometer
E feso'ota'i le potentiometer throttle i se uaea 3-uaea. + 5V ma le GND e fesoʻotaʻi i pine faʻamau i fafo o le potentiometer. O le voltage feso'ota'i ma le tulaga fa'aulu e tata'i e ala i le fa'ase'e feso'ota'i ma fa'afeso'ota'i i le TPS ulufale
(Throttle Position Sensor). O le mamao ufiufi o le potentiometer atonu e umi atu nai lo le taamilosaga o le axle throttle. O le fa'avasegaina tutusa e faia e ala i "Meafaigaluega" - "Calibrate TPS"
Fa'afuainumera Fa'aulu
O lo'o iai mea fa'akomepiuta e mafai ona fa'aoga mo example pei o le "Launch Control". Ole galuega fa'atatau e tatau ona fa'amatalaina ile TunerStudio.
Fa'amauina pine CPU
Ia matua fa'aeteete pe a fa'aogaina nei !!PPU sa'o pine!! latou leai se RC-filtering po'o vaega saogalemu. Le fa'aoga sese e mafai ona fa'aleagaina ai mea e fa'aoga ai le CPU,
Mana'omia le fa'aoga GND mea fa'aoga ua fa'agaoioia
Faʻaaigoa Faʻamatalaga
E iai mea fa'aoga analog e mafai ona fa'aoga mo example pei o le “Suavai Faaopoopo”. Ole galuega fa'atatau e tatau ona fa'amatalaina ile TunerStudio.
Fa'atonu le Saosaoa (Fidle)
O le SM3 e lagolagoina uma le 2-pin ma le 3-pin idle speed valve.
Fa'amau feso'ota'iga o le fa'atonu fa'avavevave:
- 2- pine: +12V & FDLO
- 3- pine: +12V & FDLO (tatala) & FDLC (tapuni)
O le FDLO & FDLC e otometi lava ona fesuiaʻi i luga o le PCB, faʻaaoga le pule Fidle i lalo o TunerStudio,
Fa'amumu
E mafai ona faʻagaoioia le faʻamalo e avetaʻavale eletise tuʻufaʻatasia ma le PCB pito i lalo ua faʻapipiʻiina i le 4-5or6 taʻavale malosi e mafai ai ona faʻagasolo faʻasolosolo o paʻu faʻafefe.
tui
E i ai 6 injectors outputs (INJ1-6); O tui tui e tuʻuina atu i le +12 V e ala i le faʻamalo afi ma uaea eleele o injectors o loʻo faʻagaoioia e ala i le SM3
Fa'alogo:
O le faʻatulagaina pe maualuga pe maualalo le teteʻe o tui e tatau ona tuʻuina i totonu o Faʻatonuga Autu" -" Uiga o le Injector "Aʻo leʻi faia le suʻega muamua ona o tulaga sese e mafai ona mafua ai le faʻaleagaina o tui tui poʻo le SM3a.
Tau amata (leai se fa'amaoniga):
- Fa'alavelave maualuga: PWM Fa'agata Taimi (%): 100 PWM Taimi Taimi (ms): 25.5
- Fa'aletonu maualalo: PWM Fa'agata Fa'agata (%): 30 PWM Taimi Taimi (ms): 1.5
Feso'ota'iga Bluetooth po'o le Wifi
Filifiliga bleutooth poʻo le WiFi fesoʻotaʻiga naʻo le tuʻufaʻatasia ma le Full SM3 + ECU
I luga o le Laupapa Wideband Lambda Pule
O le Bosch LSU 4.9 sensor e mafai ona fesoʻotaʻi saʻo e aunoa ma le manaʻomia e faʻatau se isi pule.
Fa'amatalaga fa'avasega TUNERSTUDIO fa'aautu laina laina lautele:
0V = Lambda 10.20 = AFR 22.35
4V = Lambda 0.650 = AFR 9.50
Amataina o le pule e mafai ona faia e ala i le GP2 (agavale solder alalaupapa) e ala i le dipswitch (Retro-Fit KdFi v1.4 laupapa) po o polokalama-poto e ala i le filifilia o le Output "Ignition G" (laulaupapa solder taumatau) ma tagata e faaaogāina manaoga seti. Ie amata lambda controller pe a uma le 30sec o le afi amata i lalo o le tuner studio
O le le fa'avaeina o le GP2 o le a i'u ai i le lambda controller.
Tu'itu'i i luga ole va'a
O le tu'itu'i IC e fa'aaogaina se tu'itu'i-fa'amoemoe ampliifier chip e faamama ai faailo tu'itu'i.
Tu'itu'i Uea
Tu'itu'i Sensor1-> Tu'itu'i 1 ECU fa'aoga ma ECU eleele Tu'i Sensor2-> tu'i tu'i ECU tu'itu'i2 ma eleele ECU
Fa'amaumauga i luga ole laiga
O le laupapa ua faʻapipiʻiina i le 1Gb o luga ole SMD-sized memory.
Sauni e fa'aoga i lalo ole lisi o fa'amaumauga SD
I luga ole va'a RTC (uati moni)
O le laupapa ua faʻapipiʻiina i se RTC saʻo, tuʻuina atu le avanoa e faʻaopoopo ai le 'taimi stamps' i luga ole va'aiga fa'amaumauga o fa'amaumauga!
Fa'afaigofie ona faitau fa'amaumauga o fa'amaumauga, fa'afaigofie le sese ma/po'o le fa'aleleia atili.
MAFAI pasi
E pei o MegaSquirt le CAN Bus hardware o loʻo nofoia i luga o le laupapa, ae tatau ona faʻatulagaina e le tagata faʻaoga pe a manaʻomia. Mo nisi faʻamatalaga i lenei mea faʻamolemole faitau le Megasquirt / MSextra taʻitasi webnofoaga.
User Remarques ma faʻamatalaga
Pepa / Punaoa
 |
K GALUEGA SM3 fa'atasi ma le Module [pdf] Tusi Taiala 1.5b, R1.5, SM3 fa'aopoopo Module, SM3 fa'aopoopo, Module |
