SKY-4001
INSTALLATION AND OPERATING INSTRUCTIONS
INTRODUCTION
SKYTECH’S remote control system was developed to provide a safe, reliable and user-friendly remote control system for gas heating appliances. Its battery operation allows the system to operate independently of household current. The system operates on radio frequencies with non- directional signals. The SYSTEM’s operating range is approximately 20 feet. The system operates on one of 255 security codes programmed at the factory
COMPONENTS
WARNING
THE SKYTECH SKY-4001 MUST BE INSTALLED EXACTLY AS OUTLINED IN THESE INSTRUCTIONS. FOLLOW INSTRUCTIONS CAREFULLY DURING INSTALLATION. ANY MODIFICATION OF THE SKYTECH SKY -4001 OR ANY OF ITS COMPONENTS WILL VOID THE WARRANTY AND MAY POSE A FIRE HAZARD.
TRANSMITTER
The transmitter operates on a 3v battery (included) made specifically for remote controls and electronic lighters. Before using the transmitter, remove the insulation tab
protecting one end of the battery in the battery compartment.
The transmitter has ON and OFF functions that are activated by pressing either button on the face of the transmitter. When a button on the transmitter is pressed, a signal light on the transmitter illuminates briefly to verify that a signal has been sent. Upon initial use, there may be a delay of five seconds before the remote receiver will respond to the transmitter. This is part of the system’s design. If the signal light does not illuminate, check the position of the transmitter’s battery
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Important Note:
FCC Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure compliance requirements, please avoid direct contact to the transmitting antenna during transmitting.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Questions about your Skytech Fireplace Remote User Manual? Post in the comments!
.
References
- User Manualmanual.tools
Remote fell open. Need to see inside of sky4001 remote to put together
How do I reassemble the Skytech SKY-4001 remote transmitter after it has fallen open?
While the official manual does not provide a detailed internal schematic for repair, the Skytech SKY-4001 transmitter is a relatively simple device. To reassemble it, follow these general steps:
If the signal light does not illuminate after reassembly when pressing the ON or OFF buttons, check that the battery insulation tab has been removed and that the battery is making firm contact with the metal terminals.
Read the full Q&A page
The FCC has some great internal photos of any device with the “FCC ID” labeling, simply search the FCC ID at https://fccid.io
This may be the Skytech Remote inside photos you are looking for, but check with your exact FCC ID
This may be the <a href="https://fccid.io/K9L-4001THTX/Internal-Photos/Internal-Photos-535712" rel="nofollow ugc">Skytech Remote inside photos</a> you are looking for, but check with your exact FCC ID
How do I reassemble the Skytech SKY-4001 remote transmitter after it has fallen open?
The FCC has some great internal photos of any device with the "FCC ID" labeling, simply search the FCC ID at https://fccid.io
This may be the Skytech Remote inside photos you are looking for, but check with your exact FCC ID
My guy installed it but there’s something weird. When the little receiver box is positioned to “remote” the fireplace turns on when I hit “off” on the clicker! And just the opposite, it turns off when I hit “on.”
Any idea what’s going on? Thanks.
Any idea what’s going on? Thanks.
Why does my fireplace turn on when I press 'OFF' and turn off when I press 'ON' on my Skytech remote?
Based on the behavior you are describing, it is highly likely that the wiring between the Skytech receiver box and your fireplace's gas valve or control module is reversed. This is a common installation error where the wires are connected to the wrong terminals, causing the circuit to close (turn on) when the remote sends an 'OFF' signal and open (turn off) when it sends an 'ON' signal.
To resolve this, please check the following:
Read the full Q&A page
I did not receive an instruction manual with my skytech remote. The model # isn’t selected, but the choices on the back of the remote are
1410T/LCD-A
1410TH-A
1001T/LCD-A
1001TH_A
Can you help me locate the correct manual?
1410T/LCD-A
1410TH-A
1001T/LCD-A
1001TH_A
Can you help me locate the correct manual?
Where can I find the instruction manual for Skytech remote models 1410T/LCD-A, 1410TH-A, 1001T/LCD-A, or 1001TH-A?
The model numbers you listed (1410T/LCD-A, 1410TH-A, 1001T/LCD-A, and 1001TH-A) are common Skytech transmitter series. Because these remotes often share a universal casing, the specific manual you need depends on the features of your remote's display and buttons.
You can find these specific manuals by using the Manuals+ Deep Search tool and entering the specific model number that best matches your remote's features. If you are unsure, the 1001TH-A is one of the most common standard thermostat remotes for Skytech systems.
Read the full Q&A page
I did not receive an instruction manual with my skytech remote. The model # isn’t selected, but the choices on the back of the remote are
1410T/LCD-A
1410TH-A
1001T/LCD-A
1001TH_A
Can you help me locate the correct manual?
1410T/LCD-A
1410TH-A
1001T/LCD-A
1001TH_A
Can you help me locate the correct manual?
Where can I find the instruction manual for Skytech remote models 1410T/LCD-A, 1410TH-A, 1001T/LCD-A, or 1001TH-A?
The model numbers you listed (1410T/LCD-A, 1410TH-A, 1001T/LCD-A, and 1001TH-A) are common Skytech transmitter series. Because these remotes often share similar programming steps, you can generally follow the instructions for the Skytech 1001-A or 1410-A series.
You can find the specific manuals for these series here:
If your remote has an LCD screen, the 1410 series manual is likely the best match. If it is a standard on/off remote without a screen, refer to the 1001 series. For further assistance, you can also use the Deep Search tool on this site to locate specific PDF versions of these model numbers.
Read the full Q&A page