SKYDANCE V1 + R6-1 Single Color LED Controller Kit

Feature

• Remote control or connected with external push switch to achieve on/off and dimming function
• Ultra sensitive brightness adjustment touch wheel
• Smooth dimming and switch without any flickering
• Auto-transmitting function: Controller automaticlly transmit signal to another controller with 30m control distance
• Light on/off fade time 3s selectable

Technical Parameters

LED Receiver’s Input and Output
Input voltage	5-36VDC
Input current	8.5A
Output voltage	5-36VDC
Output current	1CH,8A
Output power	40W/96W/192W/288W (5V/12V/24V/36V)
Output type	Constant voltage

LED Remote’s Input and Output
Output signal	RF(2.4GHz)
Working voltage	3VDC(CR2032)
Working current	＜5mA
Standby current	＜10μA
Standby time	1 year
Remote distance	30m

Dimming data
Dimming level	4096 levels
Dimming range	0 -100%
Dimming curve	Logarithmic
PWM Frequency	2000Hz

Safety and EMC
EMC standard (EMC)	ETSI EN 301 489-1 V2.2.3 ETSI EN 301 489-17 V3.2.4
Safety standard(LVD)	EN 62368-1:2020+A11:2020
Radio Equipment(RED)	ETSI EN 300 328 V2.2.2
Certification	CE,EMC,LVD,RED

Warranty and Protection
Warranty	5 years
Protection	Reverse Polarity

Mechanical Structures and Installations

Wiring Diagram

Remote function

• On/Off: Turn on/off light.
• Bright wheel: Touch to change brightness.
• Bright+/-: Adjust brightness, short press 10 levels, long press 1-6s for continuous 256 levels adjustment.
• 100%,75%,50%,25%: Get 4 kinds brightness directly.
• 3 Scene: Brightness memory, short press recall the scene, long press 2s save current brightness into the scene.

Match Remote Control (two match ways)

End user can choose the suitable match/delete ways. Two options are offered for selection:

Use the controller’s Match key

• Match:
  Short press match key, immediately press on/off key of the remote.
• Delete:
  Press and hold match key for 5s to delete all match, The light blinks 5 times means all matched remotes were deleted.

Use Power Restart

• Match:
  Switch off the power, then switch on power, repeat again. Immediately short press on/off key 3 times on the remote. The light blinks 3 times means match is successful.
• Delete:
  Switch off the power, then switch on power, repeat again, Immediately short press on/off key 5 times on the remote. The light blinks 5 times means all matched remotes were deleted.

Light on/off fade time

• Long press match key 5s, then short press match key 3 times, the light on/off time will be set to 3s, the indicator light blink 3 times.
• Long press match key 10s, restore factory default parameter, the light on/off time also restore to 0.5s.

Dimming Curve

Malfunctions analysis & troubleshooting

Malfunctions	Causes	Troubleshooting
No light	1.   No power. 2.   Wrong connection or insecure.	1.  Check the power. 2.  Check the connection.
Uneven intensity between front and rear,with voltage drop	1. Output cable is too long. 2. Wire diameter is too small. 3. Overload beyond power supply capability. 4. Overload beyond controller capability.	1. Reduce cable or loop supply. 2. Change wider wire. 3. Replace higher power supply. 4. Add power repeater.
No response from the remote	1. The battery has no power. 2. Beyond controllable distance. 3. The controller did not match the remote.	1. Replace battery. 2. Reduce remote distance. 3. Re-match the remote.

Safety information

1. The product shall be installed and serviced by a qualified person.
2. The product is non-waterproof. Please avoid the sun and rain.
3. Good heat dissipation will prolong the working life of the controller. Please ensure good ventilation.
4. Please check if the output voltage of any power supplies used comply with the working voltage of the product.
5. Ensure all wire connections and polarities are correct and secure before applying power to avoid any damages to the LED lights.
6. If a fault occurs please return the product to your supplier. Do not attempt to fix this product by yourself.

Documents / Resources

SKYDANCE V1 + R6-1 Single Color LED Controller Kit [pdf] Instructions V1 R6-1, Single Color LED Controller Kit, LED Controller Kit, Controller Kit, Single Color Controller, Controller

References

• User Manual