10-Key RF Remote Controller
Model No.: RM3
1 zone RGB or RGBW/10-key/Wireless remote 30m distance/CR2032 battery
Features
- Apply to RGB or RGBW LED controller.
- Each remote can match one or more receivers.
- RC 2032 battery powered.
- Operate with LED indicator light.
Technical Parameters
Input and Output
Output signal | l RF 2.4GHz |
Working voltage | 3VDC CR2032 |
Working current | <5mA |
Standby current | <2μA |
Standby time | 2 years |
Remote distance | 30m(Barrier-free space) |
Environment
Operation temperature | Ta: -30 OC ~ +55 OC |
IP rating | IP20 |
Safety and EMC
EMC standard (EMC) | ETSI EN 301 489-1 V2.2.3 ETSI EN 301 489-17 V3.2.4 |
Safety standard(LVD) | EN 62368-1:2020+A11:2020 |
Radio Equipment(RED) | ETSI EN 300 328 V2.2.2 |
Certification | CE,EMC,LVD,RED |
Warranty
Warranty | 5 years |
Mechanical Structures and Installations
Match Remote Control (two match ways)
The end user can choose the suitable match/delete ways. Two options are offered for selection:
Use the controller’s Match key | Use Power Restart |
Match: Short press the match key, and immediately press the on/off key on the remote. The LED indicator fast flash a few times means the match is successful. Delete: Press and hold the match key for 5s to delete all match, The LED indicator fast flash a few times means all matched remotes were deleted. |
Match: Switch off the power, then switch on the power, and repeat again. An immediately short press the on/off key 3 times on the remote. The light blinks 3 times means the match is successful. Delete: Switch off the power, then switch on the power, and repeat again. An immediately short press on/off key 5 times on the remote. The light blinks 5 times means all matched remotes were deleted. |
Key function
![]() |
On/Off: Turn on/off the light. |
![]() |
Color: Short press gets 24 kinds of static RGB color, and long press for continuous static color adjustment. |
![]() |
Mode+: Short press run the next dynamic mode, long press 2s run mode cycle. |
![]() |
Mode -: Short press runs the previous dynamic mode, long press 2s run the first mode. |
![]() |
Bright/Speed+: For static RGB color, increase brightness, short press 10 levels, and long press 1-6s for continuous 256 levels adjustment. For dynamic mode, increase speed, short press 10 levels, long press get the fastest speed. |
![]() |
Bright/Speed -: For static RGB color, decrease brightness, short press 10 levels, long press 1-6s for continuous 256 levels adjustment. For dynamic mode, decrease speed, short press 10 levels, long press get the slowest speed. |
![]() |
R/G/B: Short press gets red green or blue color directly, long press 1-6s adjust R/G/B brightness continuously to achieve millions of colors. |
![]() |
W+/-: For RGB light, short press turn on/off white(RGB mix), long press 1-6s adjust saturation continuously namely, change the current static RGB color to mixed white slowly. For RGBW light, short press turn on/off W channel, long press 1-6s adjust W brightness continuously |
Safety information
- Read all instructions carefully before you begin this installation.
- When installing the battery, pay attention to the battery’s positive and negative polarity.
A long time without the remote control, remove the battery.
When remote distance becomes smaller and insensitive, replace the battery. - If no response from the receiver, please re-match the remote.
- Gently handle the remote, beware of falling.
- For indoor and dry location use only.
Documents / Resources
![]() |
SKYDANCE RM3 10-Key RF Remote Controller [pdf] Instructions RM3, 10-Key RF Remote Controller, RF Remote Controller, 10-Key Controller, RM3, Controller |
![]() |
SKYDANCE RM3 10 Key RF Remote Controller [pdf] Instruction Manual RM3 10 Key RF Remote Controller, RM3, 10 Key RF Remote Controller, RF Remote Controller, Remote Controller, Controller |