Sinum EX-MODBUS Signal Amplifier
FAQs
Q: Can I dispose of the product in household waste containers?
A: The product should not be disposed of in household waste containers. Please transfer used equipment to a collection point where all electrical and electronic components will be recycled.
Q: How can I access the full EU Declaration of Conformity and user manual?
A: The full documents are available after scanning the QR code or at www.tech-controllers.com/manuals
PRODUCT INFORMATION
Extender EX-MODBUS is a device that enables the user to extend the signal range of peripheral devices to the Sinum central device. It connects wired devices via Modbus communication protocol and send data to the Sinum central device via WiFi/LAN network. It is designed for mounting on a DIN rail.
Description
Power
Ethernet connection
Ethernet connection activity
- Registration button
- MODBUS communication connector
- RJ45 port
- Złącze Tasmania
register the device
How to register the device in the sinus system – LAN
The extender should be connected to the same network as the Sinum central device using LAN wire (RJ45). Then enter the address of the Sinum central device in the browser and log in to the device. In the main panel, click the Settings > Devices > System modules > +. Then briefly press the registration button 1 on the device. After a properly completed registration process, an appropriate message will appear on the screen. Additionally, the user can name the device and assign it to a specific room.
to register the device in the sinus system- WiFi
On the extender, press the registration button 1 twice, the AccessPoint mode will be activated (the power LED will flash twice cyclically). The extender broadcasts a Wi-Fi network named: EX-MODBUS_XXXXXX that you can connect to. Then, in the device settings window, click Network Wifi selection (if the window does not appear in the browser, enter the extender’s IP address: 4.3.2.1), select the network to which the Sinum Central device is connected, and enter the password. If the extender successfully connects to the selected network, the power LED will stop blinking. Log in to the same network and enter the IP address of the Sinum Central device in the browser and connect to it. In the main panel, click the Settings > Devices > System modules > +. Then briefly press the registration button 1 on the device. After a properly completed registration process, an appropriate message will appear on the screen. Additionally, the user can name the device and assign it to a specific room.
NOTE: Both devices must be connected to the same WiFi network. The Wifi network has a higher priority than the LAN connection (if the extender was connected in both ways).
Technical data
| Technical data | |
| Power supply | 230V ±10% /50Hz |
| Max. power consumption | 2W |
| Operation temperature | 5°C ÷ 50°C |
| Wifi: IEEE 802.11 b/g/n (2.4 GHz) | |
| LAN: IEEE 802.3 100Mb/s | |
Notes
TECH Controllers is not responsible for any damages resulting from improper use of the system. The range depends on the conditions in which the device is used and the structure and materials used in the object construction. The manufacturer reserves the right to improve devices and update software and related documentation. The graphics are provided for illustration purposes only and may differ slightly from the actual look. The diagrams serve as examples. All changes are updated on an ongoing basis on the manufacturer’s website. Before using the device for the first time, read the following regulations carefully. Not obeying these instructions may lead to personal injuries or controller damage. The device should be installed by a qualified person. It is not intended for children to operate it. It is a live electrical device. Make sure the device is disconnected from the mains before performing any activities involving the power supply (plugging cables, installing the device, etc.). The device is not water resistant.
The product may not be disposed of in household waste containers. The user is obliged to transfer the equipment they use to a collection point where all electric and electronic components will be recycled.
EU Declaration of Conformity
Tech Sterowniki II Sp. z o.o. ul. Biała Droga 34, Wieprz (34-122) Hereby, we declare under our sole responsibility that the extender EX-MODBUS is compliant with Directive 2014/53/EU.
Wieprz, 01.06.2024
The full text of the EU Declaration of Conformity and the user manual are available after scanning the QR code or at www.tech-controllers.com/manuals
- www.techsterowniki.pl/manuals Wyprodukowano w Polsce
- www.tech-controllers.com/manuals Made in Poland
Service
- tel: +48 33 875 93 80 www.tech-controllers.com
- support.sinum@techsterowniki.pl
Documents / Resources
 |
Sinum EX-MODBUS Signal Amplifier [pdf] Instruction Manual EX-MODBUS Signal Amplifier, EX-MODBUS, Signal Amplifier, Amplifier |