Simx LHT1176 360Degree Sensor Instruction Manual
TECHNICAL SPECIFICATIONS
This sensor is an active motion detector receiving the echo of the high-frequency wavelengths (5.8GHz) it emits, to detect presence and movement
Care in product placement is critical for correct operation. Detection through doors, glass panes or thin walls, may trigger errant switching. Consider ceiling rigidity, especially mezzanines, as vibration may trigger the sensor. This sensor is rated for exterior exposed locations.
| Power Supply | 220-240V AC 50Hz |
| Max Rated Load | 1200W (resistive), 200W (LED) |
| Transmission Power | <10mW |
| HF System | 5.8Ghz CW radar, ISM band |
| Detection Angle | 360° |
| Detection | 4-20m Diameter (approx.) |
| lOsec — 12min (approx.) | |
| Time Setting | |
| Light Control | 10 LUX — Daylight |
| Power Consumption | <0.9W |
| Recommended Mounting Height | 3 – 5m |
| Operating Temperature | -10 to +60 degree centigrade |
| IP Rating | IP65 |
| Impact Rating | 109 |
| Mounting | Exterior, wet and damp locations, ceiling or wall mount |
IMPORTANT
Al electrical work must be carried out in accordance with local and national electrical codes as applicable. We strongly recommend that this sensor is installed by a registered electrician.
Always switch power off prior to installation. A means of mains power isolation must be installed in the circuit for the purpose of safe access for any internal cleaning, recalibration, or maintenance.
Any changes or modifications made or attempted to this product, or product installed contrary to these installation instructions without the prior written approval of the manufacturer, will void any and all stated warranties.
INSTALLATION
- Switch off the power supply before commencing any electrical work
- Select the desired mounting location.
- Remove cover with short clockwise twist. Mount to desired location, and mark and dil power entry and mounting holes. Care should be taken to avoid drilling or screwing into concealed wiring/plumbing.
- Feed the power and load cables through celing hole.
- Connect the power and load cables to the connection terminal according to the electrical connection. Do not exceed the max rated load.
- Secure the sensor to the ceiling firmly. This microwave sensor cannot detect through most metal surfaces. Ensure cable entry is sealed to IP65.
ELECTRICAL CONNECTION
Do not switch different lamps on same circuit ) i.e. LED & Fluor combined.
Wiring Diagram
CALIBRATION SETTINGS
Detection Setting (Sensitivity)
After mounting the sensor light at a height of 2.5m, tum the reach control completely in anti-clockwise direction to select minimum reach (approx. 4m diameter), and tum the reach control completely in a clockwise direction to select the maximum reach (approx. 20m diameter).
Time Setting
“The light can be set to stay ON for any period of time between approx.10sec (dlial tumed fully anti-clockwise) and a maximum of 12min(dial tumed fully clockwise).
Any movement detected during the “on” time will reset the timer.
NOTE: After the light switches O, it takes approx. 1sec before it is able to start detecting movement again. The light will only switch on in response to movement once this period has elapsed.
Light Control Setting
‘The chosen light response threshold can be from approx. 2-2000lux. Tumn it fully anti-clockwise to select night operation at about 2 Lux. Tum it fully clockwise to select daylight operation at about 2000lux. The knob must be turned fully clockwise when adjusting the detection zone and performing the walk test in daylight.
Troubleshooting
| Malfunction | Cause | Remedy |
| The load will not work |
|
|
|
|
|
|
|
|
| The load works always |
|
|
| The load works without any identifiable movement |
|
|
|
|
|
| The load will not work despite movement |
|
|
PRODUCT COMPLIANCES
| AS/NZS60335.1: 2020 | IEC60669-1: 2017 | IEC60669-2.1 |
| EN55015: 2013+A1:2015 | EN61547: 2009 | EN61000-3.2:2014 |
| EN61000-3.3: 2013 | EN300 440 v2.1.1: 2017 | EN301 489-1V2.2.0:2017 |
| EN301 489-3V2.1.1: 2017 | EN51479: 2010 |
MANUFACTURERS EXTENDED WARRANTY
This product is guaranteed by SIMX Ltd for 3 years from the date of purchase against faulty materials or workmanship which affects its designed abilty to switch or operate. During this period if the product has a defect of this nature it will be repaired or replaced free of charge by SIMX with the same ftem, or a similar one of higher specification. ON CONDITION THAT:
The buyer returns it to the seller from whom it was bought, freight paid.
The product has been bought by the user. ie a receipt/sales invoice is produced as proof of purchase.
The product has not been misused or handled carelessly, installed in anyway contrary to the installation instructions, used on a supply voltage other than that indicated in the product specifications, o installed in any unusually exposed or harsh environmental conditions.
This guarantee excludes liability for discoloration of paint or plastic, or any user serviceable parts. It does not confer any rights other than those expressly set out above and does not cover any claims for consequential loss or damage.
Our Goods come with guarantees that cannot be excluded under New Zealand or Australian Consumer Laws. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the Goods repaired o replaced if the Goods fail to be of acceptable quality and the failure does not amount to a major fall
Distributed by: S Lined
Ph: 649 250 1660 | Technical Support Ph: +64 9 259 1662
Email: sales@sim.conz | www.simx.conz | weveventair.com.au
Specifications are subject to change without notice
Documents / Resources
 |
Simx LHT1176 360Degree Sensor [pdf] Instruction Manual LHT1176 360Degree Sensor, LHT1176, 360Degree Sensor, Sensor |
