SIIG CE-KV0G11-S1 2-Port 4K HDMI KVM Switch User Manual

4K Scaler Function Ensure Pixel-to-Pixel Matching for Most Displays
3 Ways Control Methods for Easy Selection:
- Front Panel Push Buttons
- Hotkey Control
- Roaming Mouse Switch
Keyboard &Mouse Plug-n-Play, No Software & Drivers Required

Support Windows / Linux
Support 3.5mm Audio & HDMI Audio

Package Contents

2-Port 4K HDMI KVM Switch with PBP Roaming Mouse &PIP

Power Adapter 12V/1.5A
User manual

LAYOUT

FRONT PANEL

USB HID Cconsole port (for keyboard & mouse use only)

USB 3.0 port at console for USB peripherals SGbps, 5V/900mA,
Link: Green, connected PC is power on Select: Red, connected PC is selected

Switch Button: Press to select PC

REAR PANEL

Power Jack: DC 12V/1.5A (support DC 9V-12V, 1.5A) USB HID Console ports
(for keyboard & mouse use only)

HDMI output: resolution up to 4K@30Hz
Speaker/Earphone port at console connect to Speaker/Earphone

PC-x input ports:
- HDMI input for PC-x
- USB 3.0 Type-B port for PC-x
- Speaker/Earphone port for PC-x
USB 3.0 port at console for peripherals 5Gbps, 5V/900mA

Hotkey Control

Basic Operation
The operation of the KVM switch is mainly through hotkey controls.

Hotkey Leading Codes ( HK_LCode)

A Hotkey command is a short keyboard sequence for selecting a computer, activating computer scan, etc. KVM Switch interprets keystrokes for hotkeys all the time. A hotkey sequence starts with HK_LCode followed by one or two more keystrokes. A built-in buzzer generates a high-pitch beep for correct hotkey command; otherwise, one low-pitch beep generates for error and the bad key sequence will not be forwarded to the selected computer.

3 Ways HK_LCode

Screen Layout Control
Use Hotkey to Control Screen Layout Modes (Switch between modes or resolutions might take 10-12 seconds)

These modes are up-scaled outputs as follows:

OR/7R: Input = 2560×1440@60hz & Up-Scaled to 3840×2160@30Hz Output
OH / 7H: Input = 1920×1080@60Hz & Up-Scaled to 3840×2160@30Hz Output
0G/7G: Input = 1920×1080@60Hz & Up-Scaled to 2560×1440@60Hz Output
00/70: Input = 2560×1080@60Hz & Up-Scaled to 3440×1440@30Hz Output

This Video Up-Scaling Function Is Specially Useful for Source Compatibility or KVM Extender Compatibility. For Example

Source ls Capable of Only 1080p Output
Source Is Placed 150M away & Requires Long-Reach Function of HDBaseT Extension (1080p)

In Such Cases, The Scaled Output Can Improve Image Clarity on Modern Hi-Resolution Displays. Switching between screen layout modes might require image fine-tuning (User can save fine-tunned setting to user’s presets

PBP MODES (MODE 1&2 )

Mode 1 (Top – Bottom PBP)

HK_LCode+”L-Win”(Hold)+”1″+”U”rQ”rF” (See Screen Layout Control)
HK_LCode+”L-Alt”(Hold)+”Q”+”1″ (To Configure Roaming Mouse Top-Bottom Mode, If nececcery)

Mode 1 Fcaturcs Vcrtical PBP Modo, Thc KVM Switch Scnds Proper EDID to Both Video Source. The Display Must Support Top-Bottom PBP Function. Roaming Mouse is Configured as Top-Bottom & No Boundry.

Mode 2 Landscape ( Left-Right PBP)

“L-Ctrl”+”L-Ctrl”+”L-Win”(Hold)+”2″+”U”rarF”/| “N”/”M””Y” (See Screen Layout Control)

HK_LCode+”L-Alt”(Hold)+”Q”+”2″ (To Configure Roaming Mouse Left-Right Mode, If nececery)

Mode 2-Landscape Features Left-Right PBP Mode, The KVM Switch Sends Proper EDID to Both Video Source. The Display Must Support Left-Right PBP Function. Roaming Mouse is Configured as Left- Right & No Boundry.

Mode 2 Portrait ( Top-Bottom PBP)

Turn The Display 90°
Configure 2 Computers to Display 90° Views
HK_LCode+”L-Win”(Hold)+”2″+”U”/”Q’/F”r”N””M°”Y” (See Screen Layout Control)

HK_LCode+”L-Alt”(Hold)+”Q’+”1″ (To Configure Roaming Mouse Top-Bottom Mode, If nececcery)

Mode 2 Portrait Features Top-Bottom PBP Mode, The KVM Switch Sends Proper EDID to Both Video Source. The Display Must Support Top-Bottom PBP Function. Roaming Mouse is Configured as Top- Bottom& No Boundry.

Full Screen & PIP Modes ( Mode 0 & 7 )

Mode 0 ( Full Screen )
(a) HK_LCode+”L-Win”(Hold)+”0″+”U”rQ””F””N”” M””R”/”H”/”G”O” (See Screen Layout Control)

Mode 0 Features Full Screen Mode. The Unit Works Like Traditional KVM Switch. User Can Copy EDID from Main Output in This Mode. Click Port Selection Button to Switch Computer. Roaming Mouse Disabled in This Mode.

Mode 7 (PIP)
(a) HK_LCode+”L-Win”(Hold)+”7″+”U”/”Q'”F””N”” M”R””H”rG’/”O” (See Screen Layout Control)

Mode 7 Features PIP Mode. Selected Computer’s Content Are Showed on Display as PIP Image. Click Port Selection Button to Switch Computer. Roaming Mouse Disabled in This Mcde

PIP<->Full Screen Mode Swap

PIP Location Control

Full Screen & PlP Modes (Mode 0 8& 7)

PIP Size Control

PIP Transparency Control

Advanced Operation Image Fine-Tuning

Image Re-Syncronize
If the image engine doesn’t work properly, image re-syncronization should be proceed to resume normal operation.

Image Resyncronize
HK_LCode+”L-Win”(Hold)+”L-Alt”(Hold)+”Del” –

Video Compensation Adjustment
In different resolution & layouts, there might be slight difference in compensation requirement which might result in image fliker. Adjust video compensation can greatly improve image quality under such circumstances.

Adjust Port 1 Video Compensation
- I HK_LCode+”L-Win”(Hold)+”F11″+”1″/”|*

Adjust Port 2 Video Compensation
- HK_LCode+”L-Win”(Hold)+”F12″+”1″/”|”

User’s Presets

User can restore up to 8 presets.

Save Current Setting to User’s Preset (1-8)
- i HK_ LCode+”L-Win”(Hold)+”L-Shift”(Hold)+”=+”Fí-“F8”
I Load User’s Preset (1-8)
- I HK_LCode+”L-Win”(Hold)+”L-Shift(Hold)+”F1″”F8″

Hotkey Control Basic

Key Sequence	I Function
HK LCode + “1” ~ “2”	Computer *Port Selection* 1-2
HK LCode + “FS”	Audio Follow Port Switching Off/ On
HK LCode + “A”	Force Audio Follow to Current Port
HK LCode + “F7”	USB 3.2 Gen 1 Follow Port Switching On / OFF
HK LCode + “U”	Force USB 3.2 Gen 1 Follow to Current Port
HK_LCode + “L-Alt”(Hold) +”R-Ctrl” + Release”L-Alt”	Change HK_LCode “L-Ctrl” to “R-Ctrl”
HK_LCode + “L-Alt”(Hold) +”L-Ctrl” + Release”L-Alt”	Change HK_LCode “R-Ctrl” Back to “L-Ctrl”
HK_LCode + “L-Alt”(Hold) + “F”+”A”+”C”	Return to Factory Default
HK_LCode + “CapsLock”	Find Mouse Cursor (Mouse Cursor Moves to Center ofThe Desktop)
HK_LCode + “Tab”	Swap Port 1 & Port 2 Video Position
HK_LCode + “9”	Swap Port 1 & Port 2 Control
HK_LCode +“L-Shilt“(Hold)+ “1”/ ‘T’	Switch Control to Previous / Next Enabled Computer

Hotkey Control Mouse Roaming

Hotkey Control – PIP/PBP Video Mixing

Key Sequence	Function
PBP FUNCTION
HK_LCode + “L-Win”(Hold)+”l”+”U” / “Q” / “F”	Mode 1 (Top-Bottom PBP Mode) See Screen Layout Control
HK_LCode + “L-Win”(Hold)+”2″+”U” I “Q” I “F” / “N” /”M”/”Y”	Mode 2 (Left-Right PBP Mode) See Screen Layout Control
Full Screen & PIP FUNCTION
HK_LCode + “L-Win”(Hold)+”O”+”U” I“Q“/“F“I“N“ /“M“/“R“/“H“/“G“/“O“	Mode O (Full Screen Mode) See Screen Layout Control
HK_LCode + “L-Win”(Hold)+”7″+”U” I “Q” I “F” / “N” / “M” / “R” / “H” / “G” / “O”	Mode 7 (PIP Mode) See Screen Layout Control
HK_LCode + “L-Win”(Hold)+”Fl”~”F4”	Configure PIP Screen Position : F1 = Top-Right, F2 = Top-Left, F3 = Bottom Left, F4 = Bottom-Right
HK_LCode + “L-Win”(Hold)+”Page Up” / “Page Down”	Configure Main Screen Size : Page UP = Enlarge, Page Down = Shrink
HK_LCode+”L-Win”(Hold)+”j / f’	Configure PIP Screen Size : i = Enlarge, L = Shrink
HK_LCode+”L-Win”(Hold)+”+- / –>”	Configure PIP Screen Transparency : +- = Less Transparent, –, = More Tranparent
HK_LCode+”Fl”	Change between Full Screen Mode & PIP Mode
Image Fine-Tuning
HK LCode+”L-Win”(Hold)+”L-Alt”(Hold)+”Del”	Re-Syncronize Video Engine
HK LCode+”L-Win”(Hold)+”Fl l “+”j” / T’	Adjust Port 1 Video Compensation
HK LCode+”L-Win”(Hold)+”F12″+”j” / “f’	Adjust Port 2 Video Compensation
User’s Presets
HK LCode+”L-Win”(Hold)+”L-Shift”(Hold)+”=”+”Fl “~”F8”	Save Current Settings to Use(s Preset 1-8
HK LCode+”L-Win”(Hold)+”L-Shift”(Hold)+”Fl”~”F8″	Load User’s Preset 1~8

Documents / Resources

SIIG CE-KV0G11-S1 2-Port 4K HDMI KVM Switch [pdf] User Manual
CE-KV0G11-S1, 2-Port 4K HDMI KVM Switch, HDMI KVM Switch, KVM Switch, CE-KV0G11-S1, Switch

References

User Manual

SIIG CE-KV0G11-S1 2-Port 4K HDMI KVM Switch User

Features