SIIG 4K60Hz Quad-View HDMI Mouse Roaming KVM Processor
Safety and Notice
The device has been tested for conformance to safety regulations and requirements, and has been certified for international use. However, like all electronic equipment, the device should be used with care. Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit.
- Follow all instructions and warnings marked on this unit.
- Do not attempt to service this unit yourself, except where explained in this manual.
- Provide proper ventilation and air circulation and do not use near water.
- Keep objects that might damage the device and assure that the placement of this unit is on a stable surface.
- Use only the power adapter and power cords and connection cables designed for this unit.
- Do not use liquid or aerosol cleaners to clean this unit.
- Always unplug the power to the device before cleaning.
Features
- 4x HDMI inputs and 2x HDMI outputs
- Input resolutions support from 640×480 to 4k@60Hz (4:4:4 8bits), interlaced or progressive
- Output resolutions support up to 4K@60Hz 4:4:4 8bits
- Supports full screen & quad-view display
- HDCP 1.4/2.2 compliant
- Supports UR audio extract
- Supports un-compressed 7.1 ch digital HDMI
- Supports Web control, IR remote and front panel control
- Supports mouse roaming at the default Quad view mode
- Supports two USB3.0 ports to share USB devices
- Supports independent HID keyboard & mouse ports
- Supports hotkey control
- Plug and Play without any driver needed
- Firmware upgradable
Package contents
- 4K60Hz Quad-View HDMI Mouse Roaming KVM Processor
- IR remote control
- IR receive cable
- Power adapter DC 12V/3.33A
- User Manual
Layout
Front Panel
- Full screen display: source selection
- Display mode : select display mode
- Audio Lock: lock the selected PC stereo audio in/out to console
- USB Lock: lock the selected PC USB to console
- IR SENSOR: receiving the IR commands from IR remote
Rear Panel
- Power switch:
- DC power jack: connect to power adapter DC 12V/3.33A
- IR Receiver: for plugging in the extension IR receive cable
- HDMI input connect to PC HDMI output
- L/R Stereo Audio output connect to speaker
- Console HDMI OUT: connect to display (1&2 have same video output)
- RS-232 control port: reserved
- Ethernet: connect to LAN for WEB control
- Micro USB: for Quad-Viewer F/W update
- USB HID ports: only for keyboard and mouse use
- Micro USB: for KVM F/W update
- Console USB 3.0 hubs: connect to USB devices, 5Gbps, 5V/900mA
- Console Audio: connect to 3.5mm speaker and microphone
- KVM USB 3.0 Type-B 1-4: connect the USB cable to PC
- KVM Stereo Audio IN 1-4: connect the 3.5mm cable to PC
- KVM Stereo Audio OUT 1-4: connect the 3.5mm cable to PC
- 2-Pin Dip Switch: for KVM F/W update
Hotkey
Default setting, all of the following commands begin by pressing the [Scroll Lock] or [Ctrl] key twice. Please follow the Hotkey command listed below for selected operating functions:
IR remote control
Web control
The default IP is 192.168.1.179
User can choose Operator or Adm in account to login.
- The password of Operator: operator
- The password of Adm in: ad min
- Routing:
We provide full screen, quad, and 18 preset modes for user to select. Then you can set different channels (1-4) for windows (A-D) and select the sound output source. In addition, you can turn on or turn off the sound and screen of each window arbitrarily.
* The preset mode does not support the mouse roaming function.
- 1/0 Status:
- Video Setup:
- Output Resolution: Select the output resolution.
- Select Window: Select the window you want to set.
- Picture Settings: Set the picture details for the selected window, including “Brightness”, “Contrast”, “Saturation”, and “Hue”.
In addition, you can determine if the window’s label/border is turned on or off.
- Windows Setup:
First, choose a preset mode to set, and then you can set individually for each window, including “X Position”, “Y Position”, ‘Width”,
“Height”, etc. You can also directly select the area to move the position and change the size. If you choose live mode, you can see the changes from the screen immediately after setting. Besides, you can also set different channels (1-4) for windows (A-D) and select the sound output source here.
- Routing
- HPD Control:
You can re-plug input and output by clicking “PULSE” button.
- HDCP:
You can set HDCP mode for each input, including “Reject”, “Accept 1.4 only”, and “Accept 1.4 & 2.2”, and you can also set the output mode, including “Follow Input”, “Always Encrypt 1 .4”, and “Always Encrypt 2.2.”
- Background:
Reserved - Names:
You can set names for 18 preset modes. You can also set names for inputs and windows to be shown with the video. After you finish naming, remember to click “SAVE” button to save the settings.
- EDID mode:
You can select EDID mode of input 1-4, and check the name of each EDID and whether to lock it.
- EDID Copy:
You can select EDID from output and inputs to copy, and select the destination. Then click “Copy” button to complete the copy.
- EDID Info:
You can choose different input EDID through the drop-down list to check the feature and audio formats.
- EDID Upload/Download:
You can click “BROWSE” button to open EDID from file, and select the destination. Then press “UPLOAD” button to upload EDID. You can also download EDID to your computer.
- Network setting:
- System:
- Power:
- Lock/ Unlock: Click button to lock or unlock the device.
- Power Off/ Unit powered on: The device is powered on. Click
- “Power Off’ button to turn off the power
- Power On/ In standby mode: The device is in standby mode. Click “Power On” button to turn on the power.
OSD Control
|
1. Main |
Presets | Full Screen, Quad, Preset 1-18 |
| Routing | Input 1-4, Off | |
| Audio | Input 1-4, Mute | |
| Switch Mode | Seamless, Fade In/Out, Dissolve, Wipe | |
| Wipe Mode | Left to Right, Right to Left, Up to Down, Down to Up | |
| Transition Time | 0.0-10.0 | |
| HDR | Enable, Disable | |
|
2. Setup |
Output Resolution |
480p, 576p, 720p 50Hz, 720p 59.94, 720p
60Hz, 1080p 30Hz, 1080p 50Hz, 1080p 59.94Hz, 1080p 60Hz, 2160p 30Hz, 2160p 50Hz, 2160p 59.94Hz, 2160p 60Hz |
|
Window Setup |
Picture (Brightness, Contrast, Saturation, Hue), Layout (X Position, Y Position, Width, Height, Priority), Label (On, Off) | |
| HPD Control | Input 1-4, Pulse ALL, Output | |
| HDCP | Follow Input, Always On 1.4, Always On 2.2 | |
| Background | Reserved | |
| Audio Mode | Follow Full-Screen, Fixed | |
| Save Preset | Preset 1-18 | |
|
3. EDID |
lnput1-4 |
External, Custom, Internal 1080p30, Internal 1080p60, Internal 4K30, Internal
4K60 |
|
4. Network |
IP Settings | Mode, IP Address, Subnet, Gateway, HTTP Port |
|
TCP/Telnet Settings |
TCP Access, Telnet Port, Login Message, and Telnet Login | |
|
5. System |
Unsolicited Feedback | Enable, Disable |
| OSD Timeout | Off, 5 seconds, 10 seconds, 30 seconds,
60 seconds |
|
| Firmware Version | Firmware Version information | |
| Factory Reset | No, Yes | |
| Reboot | No, Yes |
Firmware update
Firmware update is proceeded through Micro-USB
- KVM F/W update
- Connect the Micro-USB to USB cable between PC and device
- Set dip switch [PIN#1,PIN#2] to ON[
], OFF [
]and then power on device - Open firmware update software and then select COM Port
- Click “KVM” button to open “KVM Firmware Update” windows.Check all items and click each” … ” button to select the file which you want to write into the device.Click the “Burn” button to start the firmware update
- After updating, please set the dip switch [PIN#1,PIN#2] to OFF[] ,ON[] and power cycle the device
Thank You for your purchase!
Support
For more info or tech support http://www.siig.com/support
Apr, 2022 Copyright© 2022 by SIIG, Inc. All rights reserved.
Documents / Resources
 |
SIIG 4K60Hz Quad-View HDMI Mouse Roaming KVM Processor [pdf] User Manual 4K60Hz, Quad-View HDMI Mouse Roaming KVM Processor, 4K60Hz Quad-View HDMI Mouse Roaming KVM Processor, HDMI Mouse Roaming KVM Processor, Mouse Roaming KVM Processor, Roaming KVM Processor, KVM Processor, Processor |
