VEVOR P8038 Heat Press Machine

Getting Started

A diagram illustrates the VEVOR P8038 heat press machine, a clamshell-style device featuring an adjustable arm and a flat heating platen.

Start Here

[warning-symbol] Warnings must be followed carefully to avoid body injury.

The machine is suitable for printing patterns on a variety of items including T-shirts, mugs, caps, ceramic tiles, mousepads, phone cases, and other flat or curved surfaces.

Transfer Parameters (for reference)

Operation and Setup

1. Turning On/Off and Starting

Press the power switch located on the side of the thermostat to start the machine. Press the main button once to begin the countdown timer; press again to reset it.

2. Setting Temperature/Time

Press the main button once to set the temperature. Press it twice to set the time. Pressing again exits the setup mode. The machine automatically exits the temperature/time setup state if no operation is performed for 5 seconds.

3. Adjusting Temperature/Time

Use the [plus-symbol] button to increase and the [minus-symbol] button to decrease the set time or temperature.

4. Changing Temperature Units (°C/°F)

While the machine is powered on, press and hold both the [plus-symbol] and [minus-symbol] buttons simultaneously to switch between Fahrenheit (°F) and Celsius (°C).

5. Setting Auto Shutdown Time

Press and hold the main button for 5 seconds to set the auto shutdown time. The factory default is 60 minutes, with a settable range from 10 to 120 minutes.

6. Temperature Correction

Press and hold the main button for 5 seconds to enter the temperature correction setting. The settable range is ±30°C, with an initial value of 0.

7. Turning Beep Sound On/Off

In the shutdown state, press the [minus-symbol] button to turn off the sound; "OFF" will be displayed. Press it again to turn the sound back on; "ON" will be displayed.

8. Important Tips

The maximum settable temperature for this machine is 210°C (410°F), and the longest settable time is 999 seconds.

Accessory Installation

The diagram illustrates the installation of a plate heating pad. It involves selecting a silica gel pad that matches the size of the plate to be sleeved, and removing the silica gel pad from the other side. The side without the silica gel pad should face upwards and be heated on the machine for 15 minutes. Then, place the hot stamping paper on the plate intended for printing. Remove the heating plate and place it on the plate, ensuring the side without the silica gel pad faces upward.

This mug heat press machine is compatible with 5-in-1 and 6-in-1 configurations.

Main Spare Parts

1. Pedestal
2. Placement
3. Heating plate
4. Handle
5. Aviation connector
6. Button
7. Lift knob
8. Overload protector
9. Power socket
10. Power switch
11. Column

Wiring Diagram

The wiring diagram illustrates the internal connections of the heat press machine. It shows the placement of cables on the motherboard and display, the NTC temperature probe, the hot plate, the main incoming line, the heating plate zero line, and the main incoming zero line. Key connection points are labeled CON1, CON2, P8001, H-N, and H-L.

Safety Instructions

Before operating this unit, please read these instructions completely and save them.

• [power-symbol] Keep unplugged when moving the machine.
• [power-symbol] Keep unplugged when installing accessories.
• Place the machine on a flat and stable platform and operate under ventilated conditions.
• Wear special protective equipment when operating the machine.
• [warning-symbol] Improper use may result in electric shock, fire, personal injury, and other damage.
• Do not use this machine in a hazardous location.
• Do not use when the machine is not working properly.
• Do not allow children or adults who do not understand this manual to operate this machine.
• Do not disassemble and repair this machine.
• Do not use an unsuitable AC outlet.
• Do not touch the heating plate when the machine is heating.

Warranty Information

Within 12 months, this product is covered for performance failures listed in the "Product Performance Failure Table". Services are provided free of charge upon confirmation by SUNMETA. If the failure occurs outside the warranty period, or is caused by force majeure or human causes, repair services will be charged.

Product Performance Failure Table

Product Specifications

Note: The machine supports various interchangeable heating elements for different items, including 8-inch and 10-inch plates, mug attachments, and pen attachments.