YL81C E-bike Display
Product Information
Specifications
- Product Name: E-bike Display YL81C
- Functions: Battery level indicator, Assist level adjustment and
indication, Headlight indicator, Speed indicator (real-time,
maximum speed, average speed), Distance indicator (ODO and trip
distance), Error code indicator, Bluetooth connection indicator
(reserved), Parameter setting function - Buttons: On/off button, Plus button, Minus button
- Battery Level Indicator: Five segments
Product Usage Instructions
1. Function Overview and Functional Area Layout
The E-bike Display YL81C provides various functions for
users:
- Battery level indicator
- Assist level adjustment and indication
- Headlight indicator
- Speed indicator (real-time, maximum speed, average speed)
- Distance indicator (ODO and trip distance)
- Error code indicator
- Bluetooth connection indicator
- Parameter setting function
2. General Operation
2.1 Power On/Off
To power on the display, press and hold the on/off button. To
power off the E-bike, press and hold the same button. The display
will automatically power off if the E-bike is not used for more
than 10 minutes.
2.2 Display Interface
After turning on the display, it will show real-time speed and
trip distance by default. Press the button to switch between trip
distance, ODO, maximum speed, and average speed. The distance
resets to zero after reaching 9999.9 km.
2.3 Push Assistance
Press and hold the button to enable electric push assistance
mode at a constant speed of 6km/h. Release the button to stop the
assistance.
2.4 Assist Level Selection
Press the button +/- to change the motor output power for
different assist levels ranging from 0-9.
2.5 Battery Level Indicator
The battery level indicator has five segments indicating the
charge level. Flashing outline indicates low battery and immediate
charging is required.
Frequently Asked Questions (FAQ)
Q: How do I reset the trip distance on the display?
A: The trip distance will automatically reset to zero when it
reaches 9999.9 km.
Q: What does the flashing outline of the battery level
indicator mean?
A: The flashing outline indicates low battery voltage, prompting
immediate charging.
User Msnual for
E-bike Display
YL81C
Table of Contents
1. Function overview and functional area layout ……………………………………………………………………………………………………..1 1.1 Function overview ………………………………………………………………………………………………………………………………….. 1 1.2 Functional area layout ……………………………………………………………………………………………………………………………. 1 1.3 Button definitions …………………………………………………………………………………………………………………………………… 1
2. General operation ………………………………………………………………………………………………………………………………………………1 2.1 Power on/off …………………………………………………………………………………………………………………………………………… 1 2.2 Display interface ……………………………………………………………………………………………………………………………………..1 2.3 Push assistance ………………………………………………………………………………………………………………………………………..2 2.4 Assist level selection …………………………………………………………………………………………………………………………………2 2.5 Battery level indicator ……………………………………………………………………………………………………………………………..3 2.6 Error code indicator ………………………………………………………………………………………………………………………………..3
3. General setting ……………………………………………………………………………………………………………………………………………………3 3.1 Trip distance reset ………………………………………………………………………………………………………………………………….. 3 3.2 Factory reset ………………………………………………………………………………………………………………………………………….. 3
4. Custom setting …………………………………………………………………………………………………………………………………………………… 4 4.1 Rated voltage setting ………………………………………………………………………………………………………………………………. 4 4.2 Wheel diameter setting …………………………………………………………………………………………………………………………… 4 4.3 Speed limit setting ………………………………………………………………………………………………………………………………….. 5 4.4 Metric/imperial system setting …………………………………………………………………………………………………………………5 4.5 Speed sensor setting ……………………………………………………………………………………………………………………………….. 5 4.6 Current limit setting ………………………………………………………………………………………………………………………………..6 4.7 Assistance sensor setting …………………………………………………………………………………………………………………………. 6 4.8 Power-on password setting ………………………………………………………………………………………………………………………6
5. Considerations …………………………………………………………………………………………………………………………………………………… 7
1. Function overview and functional area layout
1.1 Function overview Display M20 provides a variety of functions to meet the riding needs of users, including: Battery level indicator Assist level adjustment and indication Headlight indicator Speed indicator (including real-time speed, maximum speed (MAXS) and average speed (AVG)) Distance indicator (including ODO and trip distance (Trip)) Error code indicator Bluetooth connection indicator (reserved) Parameter setting function
1.2 Functional area layout
Battery level indicator Speed indicator
Assist level indicator
Bluetooth indicator
Headlight indicator
Speed unit Metric system: km/h Imperial system: MPH
Maximum speed indicator
Trip distance indicator ODO
Fig. 1-1 Functional Area Layout Interface of Display M20
Average speed indicator
Distance/speed unit Metric system: km, km/h
Imperial system: mile,
1.3 Button definitions There are three buttons on the operating unit of display M20,i.e., the on/off button
, plus button
and minus
button .
2. General operation
2.1 Power on/off
By pressing and holding the button
, the display will start to work and the working power supply of the controller
will be turned on. In the power-on state, by pressing and holding the button , your e-bike will be powered off. In the power-off state, the display will no longer use the battery power, and its leakage current will be less than 1uA. If your e-bike is not used for more than 10 minutes, the display will be automatically powered off. 2.2 Display interface
After the display is turned on, the display will show the real-time speed (km/h) and the trip distance (km) by default.
By pressing the button , the information displayed will be switched between the trip distance (km),ODO (km), maximum speed (km) and average speed (km).
When the distance reaches 9999.9 km, it will be automatically reset to zero.
1
Trip distance indicator
ODO
Average speed indicator
2.3 Push assistance
Maximum speed indicator Fig. 2-1 Display Interface Switching
By pressing and holding the button , the electric push assistance mode will be enabled. Your e-bike will run at the
constant speed of 6km/h. The display will show level P. By releasing the button power output and return to the state before push assistance.
, your e-bike will immediately stop
2.4 Assist level selection
Fig. 2-2 Push Assistance Indicator Interface
By pressing the button / , the e-bike assist level will be switched to change the motor output power. The assist
levels available for the display include: levels 0-3, levels 1-3, levels 0-5, levels 1-5, levels 0-7, levels 1-7, levels 0-9 and levels 1-9.
Fig. 2-3Assist Level Switching Interface 2
2.5 Battery level indicator The battery level indicator consists of five segments. When the battery is fully charged, the five segments will be all on.
In case of undervoltage, the outline of the battery indicator will flash, which means the battery has to be charged immediately.
Full battery level
4-segment
3-segment
2-segment
1-segment
Undervoltage
indication
indication
indication
indication
indication
flashing
Fig. 2-4 Battery Level Indicator Interface
2.6 Error code indicator
When a fault occurs in the electronic control system of your e-bike, the display will automatically indicate the error
code in the distance area in the format of E0**. Detailed definitions of error codes are shown in Schedule 1.
Fig. 2-5 Error Code Indicator Interface
When an error code appears on the display interface, please conduct troubleshooting in time. Otherwise, your e-bike will not work normally.
3. General setting
All parameters can only be set when your e-bike stops. The steps for general setting are as follows: In the power-on state, when the display shows the speed of 0,
3.1 Trip distance reset
Press and hold the buttons and at the same time for more than 2 seconds to reset the trip distance.
3.2 Factory reset dEF refers to factory reset. dEF-n represents not to restore factory settings, and dEF-y represents to restore factory
settings. Press and hold the buttons
and
at the same time for more than 2 seconds to enter the factory reset
interface, and press the button / to select a parameter.
Fig. 3-1 Factory Reset Interface 3
4. Custom setting
All parameters can only be set when your e-bike stops. The steps for custom setting are as follows: In the power-on state, when the display shows the speed of 0,
(1) Press and hold the buttons custom setting options;
and at the same time for more than 2 seconds to enter the selection interface of
(2) Press the button / to switch the selection interface of general setting options, and press the button
to
enter the parameter modification interface;
(3) Press the button / for parameter selection;
(4) Press the button to save the parameter and return to the selection interface of custom setting options;
(5) Press and hold the button 4.1 Rated voltage setting
to save the parameter and exit the selection interface of custom setting options.
P1 refers to the rated voltage setting option. Available values include: 36V and 48V. Press the button
to enter the
parameter modification interface. Press the button / for parameter selection. Press the button parameter and return to the selection interface of general setting options.
to save the
4.2 Wheel diameter setting
Fig. 4-1 Rated Voltage Setting Interface
P2 refers to the wheel diameter setting option. Available parameters include: 8-32 inches. Press the button
to enter
the parameter modification interface. Press the button / for parameter selection. Press the button parameter and return to the selection interface of general setting option.
to save the
Fig. 4-2 Wheel Diameter Setting Interface 4
4.3 Speed limit setting P3 represents the speed limit setting option. The adjustable range is 10~60km/h. Press the button
parameter modification interface. Press the button / for parameter selection. Press the button parameter and return to the selection interface of general setting options.
to enter the to save the
Fig. 4-3 Speed Limit Setting Interface
4.4 Metric/imperial system setting P4 refers to the metric/imperial system setting option. 00 represents the metric system, and 01 represents the imperial
system. Press the button
to enter the parameter modification interface. Press the button / for parameter
selection. Press the button to save the parameter and return to the selection interface of general setting options.
Metric system indicator interface
Imperial system indicator interface
Fig. 4-4 Metric/imperial System Setting Interface
4.5 Speed sensor setting
P5 refers to the speed sensor setting option, which can be set according to the number of magnetic heads installed on
the wheels of your e-bike. The setting range is 1-63. Press the button
to enter the parameter modification interface.
Press the button / for parameter selection. Press the button interface of general setting options.
to save the parameter and return to the selection
Fig. 4-5 Speed Sensor Setting Interface 5
4.6 Current limit setting P6 refers to current limit setting. The adjustable range is 1-25A. Press the button
to enter the parameter
modification interface. Press the button / for parameter selection. Press the button return to the selection interface of general setting options.
to save the parameter and
Fig. 4-6 Current Limit Setting Interface
4.7 Assistance sensor setting P7 refers to the assistance sensor setting option, where the number of steel magnets of the assistance magnetic disk can
be set. The adjustable range is 5, 6, 7, 8, 9, 10 and 12. Press the button
to enter the parameter modification interface.
Press the button / for paramter selection. Press the button interface of general setting options.
to save the parameter and return to the selection
Fig. 4-7 Assistance Sensor Setting Interface
4.8 Power-on password setting P8 refers to the power-on password setting option. PSd-Y means that a power-on password is required, and PSd-N
means that no power-on passwords are required. The default value of the display is PSd-N. Press the button
to enter
the modification interface, and press the button / to enter the selection interface.
If PSd-N is selected, press the button to return to the selection interface of custom setting options;
If PSd-Y is selected, press the button
to enter the password setting interface. If you don’t want to change the
password, press and hold the button to exit the custom setting interface. If you want to change the password, press the
button
for cursor movement and the button / for figure selection, and then press the button
the selection interface of custom setting options.
to return to
6
Fig. 4-8 Power-on Password Setting Interface
5. Considerations
Please use safely, and do not plug or unplug the display when it is powered on. Please avoid bumping as far as possible. Please do not alter the background parameter settings of the display at will, otherwise normal riding cannot be guaranteed. If the display fails to work normally, it should be repaired as soon as possible. Due to product upgrades of the Company, part of the displayed contents or functions of product you bought may be different form the manual, depending on the actual model.
Error codes Ef0o2r1 E022 E023
Schedule 1 Error Code Definitions
Definition
Error codes
Definition
Current Abnormality
for pEr0o2to4cols Motor Hall Signal Abnormality
Throttle Abnormality
E025
Brake Abnormality
Motor Phase Abnormality
E030
Communication Abnormality
7
Documents / Resources
 |
Shift lt YL81C E-bike Display [pdf] User Manual YL81C E-bike Display, YL81C, E-bike Display, Display |