Sengled E1E G7F Zigbee Switch
Specification
- OPERATION MODE: ON-OFF-ON
- CURRENT RATING: 1 Amps
- OPERATING VOLTAGE: 1 Volts
- CONTACT TYPE: Normally Open
- CONNECTOR TYPE: Plug In
- BRAND: Sengled
- SWITCH STYLE: Dimmer Switch
- TERMINAL: Screw
- MATERIAL: Plastic
- ITEM DIMENSIONS LXWXH: 0.29 x 0.47 x 4.64 inches
- MOUNTING TYPE: Wall Mount
- CONTACT MATERIAL: Plastic
- INTERNATIONAL PROTECTION RATING: IP00
Introduction
The SmartThings hub, Sengled smart hub Z01-hub (B087FDC5BV), Z02-hub (B07HKSTLB5), and E39-G8C (B0828KXVGQ) are all compatible hubs that can be used to pair the smart light switch directly. Use these hubs so that Alexa and Google can be used. Use Sengled’s E39-G8C (B0828KXVGQ) smart hub to connect Siri to HomeKit on an Apple device. This intelligent light switch serves as a remote control for Zigbee-enabled smart bulbs, lights, and light strips (smart plug is excluded). couple to the same hub and be required to. Without fussing with rewiring, manage your smart lighting. Use the in-app instructions to mount the wall plate if desired. Utilize the battery-operated remote to manage your Sengled Smart LEDs. With the push of a button, you may adjust brightness and use presets. You can buy one separately if your battery is dead. Battery-powered model is Cr2032.
To control lights and scenarios that you may choose at any time using the remote, use the Sengled Home app. Create your own personalized lighting scenes. To configure the button “ON” for a single click, double click, or long press to acquire more desired functionalities, use the Sengled smart home in-app instructions. All bulbs are controlled by a single click (default). Sengled smart switch is divided into two parts: A base and a remote (which operates the lights) Use the provided screws or 3M tape to mount the wall plate. Use double-sided tape to affix it to the wall. A magnetic force holds the wireless switch magnetically to the back of the pallet. Beautiful form and streamlined form design that is portable.
INTRODUCTION
Seng led Smart Light Switch enables customers to control either bulbs or whole rooms with the click of a button. The Switch means no more digging or searching for your phone when needing to control your lights, as well as having your favorite scenes pre-set to your Switch, so you can always switch to your favorite scenes when you want to.
NOTE: A hub is required to control these Smart Light Switches.
IMPORTANT SAFETY INFORMATION
Before installing the Seng led Smart Light Switch, please read and follow precautions, including:
- Do not attempt to disassemble the Switch.
- Suitable for use in operating environment between 32°F and 104°F (0°C and 40°C). Do not use where directly exposed to water. Indoor use only.
INSTALLATION INSTRUCTIONS
NOTE: If you plan to mount your Switch to a wall, Sengled recommends ensuring you can add your Switch to your Seng led Hub before attaching it to your wall.
- Download the latest version of the Sengled Home App from the Apple App Store or Google Play Store.
- Register and sign-in to your Seng led account in the app.
- Open the Sengled Home app, go to and use the + sign, and choose Smart Light Switch.
Follow the in-app instructions to finish installation.
Please do not remove the “REMOVE TO Note: PAIR” tab before you are ready to pair your Switch to the hub as you will only have one minute to successfully pair after removing the tab. If you are unable to pair, please follow the reset instructions on the next page before attempting to pair again. - Ensure Switch. your Seng led Home app can discover the switch
- (Optional for mounting your Switch) Once your Switch is successfully connected to the hub, you may connect it to a wall through three different methods.
- With the included 3M tape: please ensure the surface is clean.
- With screws: please remove the back plate and use screws to attach the wall mount.
- With the magnet: simply attach the magnet to any metal surface!
Congratulations on successfully installing your Smart Light Switch!
RESET INSTRUCTIONS
To reset your Switch, please hold down the ON and OFF buttons at the same time for at least 3 seconds. The indicator light will start flashing, indicating a successful reset. Please try to connect it to your hub at this point; you will have one minute from when it starts flashing to connect.
OPERATION
The following section outlines the operational modes of the Seng led Smart Light Switch. These can be set via your Sengled Home app, and can control bulbs in a single room, or bulbs across multiple rooms.
PRODUCT SPECIFICATIONS
| Model Number | ElE- G7F |
| Battery Life | 3 years |
| Power Supply | 3V DC (battery type Li+ CR2032) |
| Dimensions:
Switch Wall mount |
36 mm (1.4″) x 90 mm (3.5″) x 10 mm (0.39″) 74 mm (2.9″) x 118 mm (4.6″) x 9 mm (0.35″) |
FREQUENTLY ASKED QUESTIONS
Make sure your hub is on line via the Seng led Home app by pulling down the home page to refresh the device statuses, if your Hub is on line but your Switch is still offline, press any button on the Switch, and it should rejoin after this, if it continues to appear offline, try resetting it
All Sengled Smart products can be controlled except accessories and Smart Wi-Fi bulbs.
Yes, my SENGLED SMART WINDOW & DOOR SENSORS work great with my SmartThings hub.
Yes, absolutely no Alexa needed. Just pair it with a compatible zigbee hub, and program the functions as you like. Pairs and operates just fine with hubitat.
If you have a hub with zigbee and your bulbs are hooked to it you can control any bulb, without a hub you can only control sengled zigbee bulbs
The plug is paired to Sengled app so can control on/off settings of anything plugged into it by using the app to set up routines
Detect Door and Window Status, when the door/window is opened or closed, the device triggered and pushes a notification to the phone.
No, these sensors will not make any noise or sound when a door is open or close but they can be used to trigger smart home bulbs turning on or off
I believe so as the hub itself and the router connect and then you connect the bulb if you don’t start from scratch and set it up again it won’t work.
no, it is an on and off switch, not a selector switch.
You can be used in the living room, bedroom, bathroom, kitchen, office, school, store, garage, warehouse, bank, etc.
You should be able to connect the bulbs to Sengled hub and then connect Sengled hub to the echo, thereby being connected to both.
Yes, this sensor is compatible with SmartThings.
All I know is it monitors the door opening and closing.
It should, as long as you find a smooth metal surface to adhere to.
