B01-HUB2 Sengled Smart HUB
“
Specifications:
- Protocol Standard: IEEE 802.3 Ethernet
- Wireless Technology: Bluetooth 5.0
- Features: Adjustable brightness, color temperature, RGB color
adjustment - Control: Remote control via mobile app (IOS and Android) or
local control via Bluetooth - Frequency Range: 2402 MHz ~ 2480 MHz
- Antenna: Integrated on-board antenna
Product Usage Instructions:
1. Remote Control:
To remotely control the B01-HUB2, download and install the
mobile app on your IOS or Android device. Follow the app
instructions to pair the hub with your smartphone. Once connected,
you can control the lighting system’s on/off, brightness, color
temperature, and RGB color settings from anywhere.
2. Local Control via Bluetooth:
If you prefer local control, ensure your Bluetooth is enabled on
your smartphone. Pair your device with the B01-HUB2 via Bluetooth
settings. Use the app or compatible devices to adjust the lighting
settings directly within the Bluetooth range.
3. Dimming Support:
Dimming is supported through the Sengled Home app or other
compatible devices. Follow the app’s instructions to dim the lights
according to your preference.
FAQ:
1. How do I reset the B01-HUB2?
To reset the hub, press and hold the reset button for 10 seconds
until the LED indicators blink rapidly. Release the button, and the
hub will reset to factory settings.
2. Can I use third-party apps to control the lighting
system?
The recommended way to control the B01-HUB2 is through the
Sengled Home app or compatible devices. Third-party apps may not
offer full functionality or support for all features.
3. Is the B01-HUB2 suitable for outdoor use?
No, the B01-HUB2 is designed for indoor use only. It is not
suitable for outdoor or emergency lighting purposes.
“`
1. Introduction
B01-HUB2 User Manual
B01-HUB2 is based on the IEEE 802.3 Ethernet protocol standard and uses low-power Bluetooth 5.0 to develop a series of intelligent wireless whole house intelligent lighting control systems with adjustable brightness, color temperature, and color. The system can be remotely controlled through mobile app software (IOS and Android) or locally controlled via Bluetooth to achieve intelligent lighting on/off, brightness, color temperature, and RGB color adjustment.
2. Module samples
3. General information
1. support (Bluetooth LE)Bluetooth 5.0Bluetooth meshThe frequency range is 2402 MHz ~ 2480 MHz;
2. Xtensa ® dual-core 32-bit LX7 microprocessor, up to 240 MHz; 3. Supports a 10/100Mbps Ethernet port; 4. Single power supply 2.7 to 3.6V; 5. Simultaneous support for Infrastructure BSS in Station, SoftAP, or Station +
SoftAP modes Note that when ESP32-S3 scans in Station mode, the SoftAP channel will change along with the Station channel; 6. Integrated on-board antenna;
CAUTION: Not for emergency lighting. Indoor use only.
Not for use in enclosed luminaires, suitable for Damp locations, Suitable for use in operating environsmcnt bectwecn -4’F and 104°F.
NOTE: This device complies with Part 15 of the FCC rules, Operation is subject to the following twcconditions: 1) this device may not cause harmful interference, and 2) this device must accept anyinterfcrence rcccived, including intcrfercnce that may cause undesircd opcration, For dctails, rofcrencwww,senglled,com/fcc
LIMITED WARRANTY: Senaled warrants product from defects in material or workmanship for two (2years from the date of original purchase, as evidenced by the purchase date on the receipt. For moredetails, visit sengled.com
DIMMING SUPPORTED VIA SENGLED HOME APP OR COMPATIBLE DEVICES ONLY.
Support:
Ifyou encounter any issues, pleese reach out to yourlocal Sengled Support team.
Vis t the folluwing website for web support:https://support.scnglcd.com/
Send emails to:
Spport@sengledzendeskcom (USA)
Google and Google Play are tradcmarks of Googlc LLC,
Sengled USA, inc.
4646 Distribution Pkwy,#400, Buford, GA 30519
www.sengled.com
Federal Communications Commission (FCC) Interference Statement
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement: For Bulb
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment . This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.
RF warning for Portable device: For remote
The device has been evaluated to meet general RF exposure requirment. The device can be used in portable exposure condition without restriction.
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
ISED RSS Warning/ISED RF Exposure Statement
ISED RSS Warning:
This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
This apparatus complies with ISED’s RSS applicable to licence-exempt radio apparatus. The operation is authorised under the following two conditions:
(1) the device shall not cause interference, and
(2) The user of the device must accept any radio frequency interference that is experienced, even if the interference is likely to affect the operation of the device.
ISED RF exposure statement: For Bulb
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The radiation of class b repecte ISED fixed an uncontrolled environment. Installation and implementation of this material should with exchanger minimum distance between 20 cm your body. Launchers or cannot coexist this antenna or sensors with others.
ISED RF exposure statement: For remote
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. The device has been evaluated to meet general RF exposure requirement.
The device complies with the radiation exposure dose limits stated for another environment. This device has been evaluated to meet the general requirement of RF exposure.
Documents / Resources
![]() |
sengled B01-HUB2 Sengled Smart HUB [pdf] User Manual B01HUB2, 2AGN8-B01HUB2, 2AGN8B01HUB2, B01-HUB2 Sengled Smart HUB, B01-HUB2, Sengled Smart HUB, Smart HUB |