SEALEY APMS12OP Storage System with Mobile Trolley x 2 Instruction Manual

Safety
- Use two or more people to move, assemble, and install the product to avoid any injury.
- Do not leave children unattended near the product.
- Do not stand on the product or lean on the drawers or worktop.
- Wear safety glasses when removing or repositioning the slides.
- Do not alter the product in any manner.
- Do not overload products.
- Ensure Health & Safety regulations are adhered to.
- Use the cabinets on level and solid ground.
- Panels must be wall mounted.
- Be careful when opening more than one drawer.
- Securely attach the product to the wall.
Introduction
This product offers a stylish complete garage storage solution with powder-coated units for protection against scratches and solvents. Fully welded units provide a strong finish and are conveniently packed for easy delivery. Pegboard design wall panels offer additional storage and protection for the wall behind the workbench. Some assembly is required.

Important Notes
- Do not use cabinets outdoors or in damp locations.
- Avoid cleaning the cabinets with damaging solvents.
- Do not use cabinets for purposes other than intended.

MODEL NO: APMS12OP

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Refer to the instruction manual

wear eye protection during assembly

SAFETY

WARNING! Use two or more people to move, assemble, and install the product to avoid any injury.

WARNING! DO NOT leave children unattended near the product.
WARNING! DO NOT stand on the product or lean on the drawers or worktop.
WARNING! Wear safety glasses when removing or repositioning the slides. The tools could slip, which may cause personal injury.
WARNING! DO NOT alter the product in any manner. For example, do not weld external lock bars or attach unapproved electrical equipment. This may cause product damage, or injury.
WARNING! DO NOT overload products! The components of the product are designed to carry the following maximum weight capacities:
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using these cabinets.
WARNING! Use the cabinets on level and solid ground, preferably concrete.
WARNING! Panels must be wall mounted. This is not a freestanding modular system.
DANGER: Be careful when opening more than one drawer. The product could become unstable and tip. Which may cause product damage or personal injury.
DANGER: High risk of tipping if the product is not installed corectly. Securely attach the product to the wall to avoid serious injury.
DO NOT use these cabinets for any purpose other than that for which they are designed.
DO NOT use the cabinets outdoors.
DO NOT place the cabinets in a damp or wet location or an area where there is condensation.
DO NOT clean the cabinets with any solvents which may damage the surfaces or the protective coating.

INTRODUCTION

Complete your garage or workshop with this stylish complete garage storage solution. All units are powder coated to protect against scratches, mild solvents and general workshop use. Fully welded units offer a strong and professional finish conveniently packed and delivered in one tidy pallet. Pegboard design wall panels allow for additional storage whilst protecting the wall behind the workbench. Some simple assembly is required.

SPECIFICATION

Cabinet	Shelf Weight Capicity (Kg.)	Drawer Weight Capicity (Kg.)	Bottom Weight Capicity (Kg.)	Top Weight Capicity (Kg.)	Overall Weight Capicity (Kg.)
Locker	68.0	–	99.7	68.0	371.9
Wall Cabinet	–	–	22.6	–	22.6
1- drawer roller cabinet	45.3	31.8×1	45.3	45.3	167.8
4- drawer roller cabinet	–	31.8×4	–	45.3	172.3
52 inch workbench	–	–	–	362.8	362.8

NO.

DESCRIPTION

WALL

CABINET LOCKER

X2 X1

1-DRAWER 4-DRAWER R CABINET R CABINET

X1 X1

52IN

WORKBENCH

X 1

PEGBOARD

X 6

M6 HEX FLANGE NUT

8 x 2

FLAT WASHER

4 x 2

4 x 6

NO.	DESCRIPTION	WALL CABINET LOCKER X2 X1		1-DRAWER 4-DRAWER R CABINET R CABINET X1 X1		52IN WORKBENCH X 1	PEGBOARD X 6
3	KEY	0	2	2	2	0	0
4	M5 X 50 HEX TAPPING BOLT	4 x 2	4	0	0	0	4 x 6
5	M6 X 12 FLAT-HEAD BOLT	8 x 2	20	0	0	0	0
6	M5 X 12 FLAT-HEAD BOLT (on the door)	2 x 2	4	6	8	0	0
7	Adustable Leveling Feet	0	4	0	0	0	0
8	Shelf	0	3	1	0	0	0
9	Casters	0	0	4	4	0	0
10	M8 x 20 Hex Flange Bolt	0	0	16	16	0	0
11	Grab Handle	0	0	2	2	0	0
12	M8 x 16 Flat-Head Bolt	0	0	4	4	8	0
13	M8 x 65 Hex Bolt	0	0	0	0	4	0
14	M8 Hex Flange Nut	0	0	0	0	4	0

To unpack the products, start by placing the packages on a level floor. Take care when removing the packaging, and check all the contents are included. If any item is missing contact your local Sealey authorised dealer where purchased. Recycle all packaging material after removed. Next gather the tools required to construct the item.

ASSEMBLY

TOOLS REQUIRED

INSTALLING THE HANDLES

Parts required: M5x12mm bolts. Grab handles. M8 x 16mm Flat-head bolts..

Attach the handle to the front of the doors using the M5x12mm flat head bolts. Repeat for all the doors and drawers.
Attach the grab handles to the cabinet, align the holes and fix with the M8x16mm flat head bolts. (See fig 1).

INSTALLING THE CASTERS
Parts required: Caster wheels. M8x20mm Hex Flange Bolts.

Lay the cabinet on a flat surface ensuring the item doesn’t get scratched. Use the packaging material to protect the finish.
Mount the four casters to each cabinet with the M8x20mm hex flange bolts. (See fig 2).

Note: The casters with brakes should be on the front side of the cabinet.

INSTALLING THE FEET
Parts required: M6x12mm Flat-Head Bolts. Adjustable Leveling Feet.

Lay the locker on a flat surface ensuring the item doesn’t get scratched. Use the packaging material to protect the finish. Attach the adjustable leveling feet to the locker using the M6x12mm flat-head bolts. (See fig 3).

INSTALLING THE SHELVES
Parts required: Shelves.

Carefully insert the shelf into the slots either side of the cabinet.
Ensure all the shelves are placed stable. (See fig 4).

Note: The center shelf must be installed central to the lock on the cabinet door in order for the lock to work.

INSTALLING THE WORKBENCH
Parts required: M8x65mm Hex bolts. M8 Nuts. M8x16mm Flat-head bolt.

Lay the workbench on a flat surface ensuring the item doesn’t get scratched. Use the packaging material to protect the finish. Align the holes on the legs with the base of the workbench. Use the M8x16mm bolts to connect the legs to the workbench.

Use four M8x65mm hex bolts and the M8 nuts to fasten the supports to the legs.
Tighten all bolts.
Stand the workbench up to finish the step. (See fig 5).

SETUP

Planning the position of the cabinets and workbench. (See fig 6).

FIXING THE PEGBOARD TO THE WALL
Parts required: 2x4mm Flat washer. M5x50mm Hex Tapping Bolt. “Note: Wall plugs are not supplied with these units. You will need to use plugs appropriate to the wall material in which you are mounting.”

Align the pegboard and fix onto the wall using the 2x4mm Flat Washers and the M5x50mm Hex Tapping Bolts. (See fig 7).

CONNECTING THE CABINETS TO THE SHELVES
Parts required: M6 Hex Flange Nut. M6x12mm Flat-Head Bolt.

Connect the two wall cabinets with the shelves using the M6x12mm Hex Flange Nuts and M6 Flat Head Bolts (See fig 8).

CONNECTING THE CABINETS TO THE WALL
Parts required: 2x8mm Flat Washer. M5x50mm Hex Tapping Bolt. Note: Wall plugs are not supplied with these units. You will need to use plugs appropriate to the wall material in which you are mounting.”

Open the wall cabinet doors, connect the wall cabinet assembly to the wall using the 2x8mm Flat Washers and the M5x50mm Bolts. Note: Two or more persons is recommended for this step. (See fig 9).
Roll the tool cabinet under the workbench. (See fig 10).

CONNECTING THE LOCKER TO THE WALL
Parts required: 2x4mm Flat Washers. M5x50mm Hex Tapping Bolt. Note: Wall plugs are not supplied with these units. You will need to use plugs appropriate to the wall material in which you are mounting.”

Lean the cabinet against the table. Open the door of the locker and securely attach the locker onto the wall using the 2x4mm Flat Washers and the M5x50mm Hex Tapping Bolt to prevent it from tipping. (See fig 11 on the next page).

OPERATION

DRAWER REMOVAL
Pull the drawer out so that it’s almost fully extended. Push up on the black release lever on one side, while pulling down on the black release lever on the other side. Hold the levers in the positions as illustrated below, pull the drawer outward until it is released from the drawer slide. (See Fig 12).

Drawer Replacement Extend the drawer slides from the cabinet. Insert the brackets on each side of the drawer into the slots in the slides, being carefull to position them properly. Once inserted, close the drawer completely to send the slides to their proper positions.

MAINTENANCE

Lubricate the slides twice a year with a quality lubricant. This is especially necessary when the temperature drops, which may cause the bearings to be dry. Periodically clean the drawers fronts, doors, handles and other surfaces with mild soap and water. For safety, use a nonflammable cleaning fluid. Grease and oil can be removed with most standard cleaning fluids.

ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No Liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 24 months from purchase date, proof of which is required for any claim.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR

01284 757500
sales@sealey.co.uk

www.sealey.co.uk

FAQS

Q: Can these cabinets be used outdoors?
A: No, these cabinets are designed for indoor use only and should not be placed outdoors.

Q: What should I do if I need to clean the cabinets?
A: Avoid using solvents that may damage surfaces or protective coatings. Use a mild cleaning solution with a soft cloth instead.

Q: How should I secure the product to the wall?
A: Follow the installation instructions provided in the manual to securely attach the product to the wall to prevent tipping and ensure safety.

Documents / Resources

SEALEY APMS12OP Storage System with Mobile Trolley x 2 [pdf] Instruction Manual
APMS12OP Storage System with Mobile Trolley x 2, APMS12OP, Storage System with Mobile Trolley x 2, System with Mobile Trolley x 2, Mobile Trolley x 2, Trolley x 2

References

User Manual

SEALEY APMS12OP Storage System with Mobile Trolley x 2

Product Usage Instructions