SEALEY APMRM4 Modular Racking Mid Unit 2 Compartment Shelve 580mm
PRODUCT INFORMATION
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
SAFETY
- WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this product.
- Locate product in a suitable working area.
- Keep the work area clean, uncluttered and ensure there is adequate lighting.
- WARNING! Use product on level and solid ground, preferably concrete. Avoid tarmacadam since the product may sink into the surface.
- Keep the product clean and tidy in accordance with good workshop practice.
- Keep children and unauthorised persons away from the working area.
- DO NOT use the product for any purpose other than that for which it is designed.
- DO NOT exceed maximum capacity of product.
- DO NOT undertake work on the product without the workpiece being adequately secured. Use clamps or a vice (not included) to secure the workpiece. Available from your Sealey stockist.
- DO NOT use the product outdoors.
- DO NOT get the product wet or use in damp or wet locations or areas where there is condensation.
- DO NOT clean the product with any solvents that may damage the paint surface or the protective coating.
INTRODUCTION
The Sealey modular racking system is finished with a heavy-duty textured powder coat to prevent against rusting. Simply choose your base, middle, and top units and push together using nylon connectors to create versatile storage for the workshop, garage, home or office. All drawers have ball-bearing drawer slides for smooth operation and cupboard doors are fitted with spring-loaded hinges, allowing them to be fitted the side that suits your environment. Buy individually (see specific model number for full specs) or as one of our pre-created combos.
SPECIFICATION
| Model no: | APMRM4 |
| Nett Weight: | 6.70kg |
| Size (W x D x H): | 580 x 340 x 444mm |
| Shelves: | 2 |
CONTENTS
| Item | Part | Description |
| 1 | APMRM4-01 | Upright |
| 2 | APMRM4-02 | Tray |
| 3 | APMRM4-03 | Tray Divider |
| 4 | APMRB1-11 | Plastic Connector |
| 5 | MSP612.S | Machine Screw Pan Head Phillips M6 x 12mm |
| 6 | APMRB1-09 | Self-Tapping Screw ST4.8 x 30mm |
| 7 | APMRB1-10 | Expansion Plug M8 x 40mm |
ASSEMBLY
- Step 1. Assemble the uprights, and fit the trays using M6*12 as shown.
- Step 2. Assemble the tray dividers and the plastic connectors.
- Step 3. To fix on the wall, mark the wall using the hole which is at the back of the tray.
- Step 4. To fix the cabinet on the wall. Mark the wall out before drilling the hole, after the wall has been marked out drill a hole the size required see above illustration, Insert the wall plug 8*40 into the drilled hole.
- Step 5. Fix the cabinet to the wall using the self-tapping screw ST4.8*30.
- Step 6. To fix the cabinet on to a wooden wall. Mark the wall out before drilling. Drill a hole the correct size using the dimensions in the above illustration.
- Step 7. Fix the cabinet on a wooden wall with the self-tapping screw ST4.8*30, no wall plug is required.
- Step 8. Assembly complete.
MORE INFORMATION
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.
REGISTER YOUR PURCHASE HERE
- NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
- IMPORTANT: No Liability is accepted for incorrect use of this product.
- WARRANTY: Guarantee is 12 months from purchase date, proof of which is required for any claim.
CONTACT INFORMATION
- Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
- 01284 757500
- sales@sealey.co.uk
- www.sealey.co.uk
FAQs
- Q: Can I use this product outdoors?
- A: No, it is advised not to use the product outdoors to prevent damage.
- Q: What is the weight capacity of this modular racking system?
- A: The product should not exceed its maximum capacity specified in the instructions to ensure safe usage.
Documents / Resources
 |
SEALEY APMRM4 Modular Racking Mid Unit 2 Compartment Shelve 580mm [pdf] Instruction Manual APMRM4 Modular Racking Mid Unit 2 Compartment Shelve 580mm, APMRM4, Modular Racking Mid Unit 2 Compartment Shelve 580mm, Unit 2 Compartment Shelve 580mm, Compartment Shelve 580mm, Shelve 580mm |