مواد لڪائڻ

1 پروجيڪٽا انٽيلي-آر وي GEN II گھٽ پروfile 30A PWM چارجنگ سسٽم

پروجيڪٽا انٽيلي-آر وي GEN II گھٽ پروfile 30A PWM چارجنگ سسٽم

ڊيڄاريندڙ

ڌماڪيدار گيس. شعلن ۽ چمڪن کي روڪيو. چارج ڪرڻ دوران مناسب وائيٽليشن مهيا ڪريو

چارج ڪرڻ کان اڳ، هدايتون پڙهو
اندروني استعمال لاء. مينهن وسڻ نه ڏيو

For charging lead acid and LiFeP04 batteries ONLY (of the size & voltage وضاحتي جدول ۾ بيان ڪيل)
بيٽري کي هميشه صحيح وول تي چارج ڪريوtage سيٽنگ. چارجر کي ڪڏهن به اونچي آواز تي مقرر نه ڪريوtagاي بيٽري جي وضاحتن جي حالت کان

بيٽري سان ڪنيڪشن ٺاهڻ يا ٽوڙڻ کان پهريان 240V مين سپلائي کي ڊس ڪنيڪٽ ڪريو
Connect the positive battery terminals before making any ground connections. The ground connection to the chassis should be made away from the battery and any fuel line. Only connect mains after the battery is connected

بيٽري چارجر کي زمين جي ساکٽ آئوٽليٽ ۾ پلگ ان ٿيڻ گهرجي
سپلائي مينز جو ڪنيڪشن قومي وائرنگ جي ضابطن جي مطابق هجڻ گهرجي

غير ريچارجبل بيٽرين کي چارج ڪرڻ جي ڪوشش نه ڪريو
منجمد بيٽري کي ڪڏهن به چارج نه ڪريو

If AC cord is damaged, do not attempt to use Replace with a compatible earthed IEC cable immediately.
Corrosive substances may escape from the battery during charging and damage delicate surfaces Store and charge in a suitable area

This charger is not intended for use by persons (including children) with reduced physical sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible or their safety
ٻارن جي نگراني ڪئي پئي وڃي ته اهي اوزار سان راند نه ڪن

If the recreational vehicle is to be put into storage without power, please turn off the BATTER MASTER SWITCH. If the recreational vehicle is to be stored for 3 months or longer, it’s advisable to disconnect all fuses from the battery A full charge should be run every 3 months.

View Fullscreen

2.8 بيٽري گھٽ وولٽtagاي تحفظ (BLVP يا عام طور تي LVD طور سڃاتو وڃي ٿو)
PM335C ماسٽر پاور يونٽ ۾ بلٽ ان لو وول آهيtage تحفظ رلي. اهو هڪ ڀيرو بيٽري جي مقدار کي ختم ڪري ڇڏيندو لوڊtage هيٺان ٿو
حد voltage. The default setting is 10.5VDC. This can be manually turned On/Off via the LOAD button on the LCD display
نوٽ: ڪلاس C3 فعال رهندو جيستائين بيٽري سوئچ آن رهندو ۽ ڪلاس ڊي لوڊ هر وقت فعال رهندا.
2.9 بيٽري سوئچ

The PM335C unit Offers a convenient way to switch Off the output Of the service battery on-board. It protects the service battery from
being drained by electronics on board, completely isolating the battery PM335C unit also supports a remote manual battery switch
Before using the remote switch, ensure the manual battery switch at the unit is set as ” ON”
The switch is only effective when the system has no other energy resource for the load except the battery
2.10 بيٽري جي صحيح ماپ

PM335C يونٽ ۾ مائڪرو پروسيسر ذريعي ڪنٽرول ٿيل بيٽري جي ماپ جو نظام آهي. اهو بيٽري جي مقدار کي ماپيندو آهي.tage, charge/discharge current,
remaining battery capacity (in amp hours) and time remaining
Compared to conventional indicating meters even small currents can be measured and read accurately with this device. This feature
highlights faults, alarms and installation errors.
NOTE: If you have loads connected directly on the battery instead of PM335C Power Management System, the measurement will not be
درست.
NOTE: PINO. PMSHUNT will be required for heavy loads designed to be connected direct to battery to ensure SOC% accuracy
2.11 رات جو موڊ
In Night Mode, the backlight ofthe monitor will tum off and the cooling fans will operate at a decreased speed Charge current will be
reduced to half rated selection when night mode is active.6
6.1
آپريشن
دستي سوئچ
There is an ON/OFF switch on side Of the machine, which is used to contrd the mach’ne to switch on/off when is povvered by
battery ahne, and to contra the whole mach’ne to enter into skep mode when it is powered by mains power This switch must be be “ON”
in Order the Rernote S’,vitch to
6.2 ريموٽ سوئچ (اختياري)
Rem o te
remote switch terminals are hated to positive 14 terminal This requires the use Of an external switch functions
way as the manual On,’Off Battery Switch on the side of the charger. The Battery switch must be “ON” in order to use the Remote Switch line.
When not used both terminab must together
6.3 Dip switch
1234
There is 5 pin dip switch on the unit which is used for adjusting current and battery type. At this time switch 5 is not used and shouh
"آف" پوزيشن ۾
Note: lhese not to be adjusted a digital screen used6.4 Maintenance
بيٽري مانيٽر جي سار سنڀال
PM335C SyStgTIS feature buh-in battery software. TO ensure accurate readings maintain the system ‘Nith the folowing
1 : FLU the battery from AC input instead of sdar every 2 weeks
2: FLAW the battery from at East every 3 rrxmths, even in stcrage, ur*ess to earlier.
• Charge battery withAC grid until “CHG ” LED PM335C unit or “Fbat• shows on the monittx
روزاني سار سنڀال
• Confirm the S’,vitch is ON when you want to charge the battery with AC grid
• battery is 12VDC
• Ensure the Space (SDrnrn each side) beside the PM335C unit for the apptowiate ventlation
• When replacing and battery, fuly charge via AC grid to Fbat to ensure SOC% is accurat4y caibrated.
Note: If the house battery is allov.•ed to &ained to a point cannot power the system, the house battery must charged to float
mcxie via AC maims to recalibrate the internal I external shunt. Falure to do so yield an inaccurate SOC% (State of Charge 0/0),
causing premature shutdown when off-grid as the system sees tip battery as a Connection’ and gives an assumed, not accurate
SOC ‘Aue based on battey voltage.
Only the energy consumption of the loads connected on the PM335C is and cdcdated
in the data the Monit0G Unless a shunt is fitted. projecta pln PMSHUNT
For it is recanmended to switch Off the Manual Battery Switch on the unit or the