D and R Airlab-DT Module Installation Guide

مواد لڪائڻ
1 Airlab-DT Module
2 پيداوار جي ڄاڻ
2.1 وضاحتون:
3 پيداوار جي استعمال جون هدايتون
3.1 تنصيب:
4 FAQ
4.1 Q: What should I do if the new module is not functioning properly after installation?
4.2 Q: Can I install multiple Airlab modules into an Airlab-DT?
4.2.1 دستاويز / وسيلا
4.2.1.1 حوالو

Airlab-DT Module

پيداوار جي ڄاڻ

وضاحتون:

  • Product Name: Airlab Module
  • Compatibility: Airlab-DT
  • Includes: Shuttle cables, screws

پيداوار جي استعمال جون هدايتون

تنصيب:

  1. Ensure that the Airlab-DT is powered off and disconnected from
    طاقت جو ذريعو.
  2. Locate the MUX board on the Airlab-DT.
  3. Connect the delivered shuttle cables to the new Airlab module
    on the MUX board and the back print.
  4. Connect the new module with the shuttle cables.
  5. Carefully place the module inside the console again.
  6. Securely fasten the module with screws.
  7. Test all connections and functionalities before reattaching all
    سامهون پينل.

FAQ

Q: What should I do if the new module is not functioning
انسٽاليشن کان پوءِ صحيح؟

A: If you encounter any issues with the new module, double-check
all connections and ensure they are secure. If problems persist,
وڌيڪ مدد لاءِ ڪسٽمر سپورٽ سان رابطو ڪريو.

Q: Can I install multiple Airlab modules into an
Airlab-DT?

A: Yes, you can install multiple Airlab modules into an
Airlab-DT as long as they are compatible and properly installed
ڏنل هدايتن تي عمل ڪريو.

View Fullscreen

Installation instructions to install an Airlab module into an existing Airlab-DT.
Instructions: 1. Remove the screw cover strips on top and bottom of the module. 2. Remove all screws from the blank panel or the module that you want to exchange on the position. 3. Lift the front / module. 4. Remove all the shuttle cable on the module. If you remove a blank panel, these cable will not be there. 5. Remove the blank plastic plate on the backside of the Airlab-DT on the position where you want to include the new module. If you want to exchange a module or replace it for another version module, first check if the back print you have received with your Airlab-DT module is the same or not. If this back print is different, you need to exchange this print also on the backplane.
6. Connect the delivered shuttle cables that has been included at the new module on the MUX board and the back print.
7. Now connect the new module with the shuttle cables. 8. Place the module carefully inside the console again and montage the module again with
screws. 9. Test everything before you mount all front panels again.
سدا خوشقسمت رهو!

دستاويز / وسيلا

D and R Airlab-DT Module [pdf] انسٽاليشن گائيڊ
Airlab-DT, Airlab-DT Module, Airlab-DT, Module

حوالو

تبصرو ڇڏي ڏيو

توهان جو اي ميل پتو شايع نه ڪيو ويندو. گهربل فيلڊ نشان لڳل آهن *