SCORPION Tribunus III Telemetry ESC Temperature Controller Fan User Guide

Tribunus III Telemetry ESC Temperature Controller Fan

“

Specifications:

• Product: Scorpion Tribunus III Telemetry + JR DMSS
  Protocol
• Software Version: FW 16 or higher
• Communication Protocol: JR DMSS

Product Usage Instructions:

I. Software:

1. Connect Tribunus III ESC to your PC using USB-C Cable (or Vlink
   II cable + diode cable).
2. Ensure using FW 16 or higher.
3. Select JR DMSS Port in value A5 – Communication Protocol.
4. Set the correct pole pair (E3) and gear ratio (E2).
   • Note: Pole pair is 1/2 of the pole count of the motor (pole
     count / 2 = pole pairs).
   • Note: If pole pair and gear ratio are not set, electrical RPM
     will be displayed instead of mechanical RPM.

II. Hardware Connection:

1. Connect your Tribunus-III ESC to your JR PROPO receiver using a
   male to male servo extension cable.
2. Connect PC.PORT of the ESC to the SENS port of the JRPROPO
   receiver.
3. Remove propeller/pinion from the motor, check connections, and
   apply suitable battery power to the ESC.

III. Transmitter Setup:

1. Scroll to the telemetry page, press INH, and select desired
   data (TEMP-RPM-AMP-CONSUMPTION-VOLTAGE).
2. Set data more precisely (Capacity amount of battery or voltage
   alarm) by scrolling through Function list -> System list ->
   telemetry -> choose the data.

IV. Result:

Set the widgets with your desired values according to your
preference. Values sent by the ESC are: Voltage / Temp / AMP / RPM
/ Consumption.

FAQ:

Q: Is the JR DMSS protocol compatible with any other ESCs?

A: No, JR DMSS protocol is functional with Scorpion Tribunus III
ESCs ONLY.

“`

www.scorpionsystem.com Scorpion Tribunus III Telemetry + JR DMSS Protocol : User Guide
I.Software
1. Connect Tribunus III ESC to your PC using USB-C Cable (or Vlink II cable + diode cable). 2. Make sure you are using FW 16 or higher
1

NOTE: JR DMSS protocol is functional with Scorpion Tribunus III ESCs ONLY
3. Select JR DMSS Port in value A5 – Communication Protocol
Make sure your JR remote, is as well updated to the latest FW to ensure proper function !
2

4. Set the correct pole pair (E3) and gear ratio (E2)

Note: Pole pair is 1/2 of the pole count of the motor (pole count / 2 = pole pairs)

Note : If you do not set pole pair and gear ratio the electrical RPM will be displayed in the telemetry field rather than

mechanical RPM

3

II.Hardware connection
5. Connect your Tribunus-III ESC to your JR PROPO receiver
Connection is made with a simple male to male servo extension cable (patch cable) Connect the PC.PORT of the ESC, to the SENS port of the JRPROPO receiver
4

6.Remove propeller / pinion from the motor, check all connections, and apply suitable battery power to the ESC
2
5

III.Transmitter setup
1- Scroll to the telemetry page –> Press INH and select the data wanted –>telemetry values you can set are–> TEMP-RPM-AMP-CONSUMPTION-VOLTAGE

Temp RPM

F-Pack(V)= Voltage F-Pack(C)= Compsumption F-Pack(A)-Current

Go back to main page
6

2-Set the data more precisely (Capacity amount of the battery or voltage alarm) Function list –> scroll to System list–> telemetry–> choose the data

Set amount of capacity in your battery

Go back to main page
Example for the capacity alarm
Set the % of the battery you want to use

Capacity is how much remaining and consumption is how much you haved used

7

IIII.Result
Set the widgets with your desired values according to your preference. Values sent by the ESC are : Voltage / Temp /AMP/RPM / Consumption
8

Documents / Resources

SCORPION Tribunus III Telemetry ESC Temperature Controller Fan [pdf] User Guide Tribunus III, Tribunus III Telemetry ESC Temperature Controller Fan, Telemetry ESC Temperature Controller Fan, Temperature Controller Fan, Controller Fan, Fan

References

• User Manual