scheppach TW1000 Workshop Trolley Instruction Manual

scheppach TW1000 Workshop Trolley

Explanation of the symbols on the equipment

			Read the operating instructions to reduce the risk of injury.
			Warning – Always only open one drawer.
			Warning – Do not tilt more than 5°.
			The maximum permitted load of the workshop trolley is 450 kg.
			The maximum permitted load of the drawer is 15 / 20 kg.
			Releasing/engaging the brake
			Releasing/engaging the drawer
			Workshop trolley lock / unlock
			The product complies with the applicable European directives.
			The product complies with the applicable Serbian directives.
Attention!			We have marked points in these operating instructions that impact your safety with this symbol.

Introduction

Manufacturer:
Scheppach GmbH
Günzburger Straße 69
D-89335 Ichenhausen

Dear customer,
We hope your new tool brings you much enjoyment and success.

Note:
According to the applicable product liability laws, the manufacturer of the device does not assume liability for damages to the product or damages caused by the product that occurs due to:

• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service technicians,
• Installation and replacement of non-original spare parts,
• Application other than specified.

We recommend:
Read through the complete text in the operating instructions before installing and commissioning the device. The operating instructions are intended to help the user to become familiar with the machine and take advantage of its application possibilities in accordance with the recommendations. The operating instructions contain important information on how to operate the machine safely, professionally and economically, how to avoid danger, costly repairs, reduce downtimes and how to increase reliability and service life of the machine.

In addition to the safety regulations in the operating instructions, you have to meet the applicable regulations that apply for the operation of the machine in your country. Keep the operating instructions package with the machine at all times and store it in a plastic cover to protect it from dirt and moisture. Read the instruction manual each time before operating the machine and carefully follow its information. The machine can only be operated by persons who were instructed concerning the operation of the machine and who are informed about the associated dangers. The minimum age requirement must be complied with.

In addition to the safety notices contained in this operating manual and the particular instructions for your country, the generally recognised technical regulations for the operation of identical devices must be complied with. We accept no liability for damage or accidents which arise due to non-observance of these instructions and the safety information.

Layout

1. Handle
2. Key
3. Castor
4. Castor with brake
5. Fixed wheel

Scope of delivery

• Workshop trolley
• Castor
• Castor with brake
• Fixed wheels
• Fastening screws
• Key
• Operating Manual

Intended use

• The trolley is designed solely for the storing of tools with a maximum load of 450 kg. It is solely intended for private use indoors and is not suitable for commercial applications.
• Only use the trolley as described in this operating man-ual. Any other use is considered unintended use and can lead to damage or even injury. The trolley is not a toy.
• The manufacturer or dealer assumes no liability for damage caused by unintended or improper use.
• Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the equipment is used in commercial, trade or industrial businesses or for equiv-alent purposes.

Safety information

Risk of injury!
Improper use of the trolley increases the risk of injury.

• Always check the trolley before use. Do not use the trolley if it is damaged.
• Only move the trolley by pushing it to another location.
  To avoid injury, do not pull the trolley
• Always ensure the workshop trolley is secure when setting it up.
• Do not climb or stand on the trolley.
• Close and lock all of the drawers before pushing the trolley. Otherwise, the drawers could open while pushing so that the trolley becomes unstable.
• Do not overload the drawers of the trolley.
• Keep the trolley away from children. Do not leave the trolley unattended in the vicinity of children.
• Keep children away whilst assembling the trolley.
• This product includes screws and other small parts.
• These could cause asphyxiation if they are swallowed or inhaled.
• The trolley is very heavy when fully loaded. There is a risk of tipping in the event of improper opening. Do not open multiple drawers at the same time.
• Do not assemble the trolley on a moveable object to avoid tipping.
• Warning: Only position and operate on a solid, level surface. The trolley can become unstable and tip over if it is kept or pushed on a sloping surface.
• Always block the rotatable castors after the trolley has been pushed to the desired location to prevent the trolley from rolling away.
• Do not make any changes to the trolley. For example, do not weld any external bars and do not attach any electrical devices to the trolley.
• Do not attach or mount the trolley to a vehicle. Do not pull the trolley with a vehicle.
• Only use original spare parts and accessories.
• Store these safety instructions safely.
• Observe all safety instructions. If you disregard the safety instructions, you endanger yourself and others.

Technical data

Subject to technical modifications!

Before starting the equipment

Check the device for transport damage. Immediately report any damage to the transport company that de-livered the device.

• Open the packaging and remove the device care-fully.
• Remove the packaging material as well as the pack-aging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport damage.
• If possible, store the packaging until the warranty period has expired.

ATTENTION!
The device and packaging materials are not toys! Children must not be allowed to play with plastic bags, film and small parts! There is a risk of swal-lowing and suffocation!

Attachment and operation

 ATTENTION!
Always make sure the device is fully assembled before commissioning!

The workshop trolley is largely assembled and you need only fit the wheels as follows:

Mounting the wheels (fig. 1 – 3)

• First, remove the tools provided from the trolley.
• Mount the trolley on a sufficiently large and scratch-proof surface. If necessary, pad the trolley with packaging material to prevent scratching of the painted surfaces.
• Turn the workshop trolley over and mount the wheels as follows.
• Position the fixed castors (5) at the rear and the rotatable castors (3,4) at the front (handle side (1)) of the trolley. Line up the holes in the castors with the holes in the trolley.
• Attach the castors to the underside of the trolley using an Allen key. Only use the screws provided for this.

User manual for voltage tester (125 to 250 V~)
To measure alternating current (AC) voltage
The voltage values specified on the voltage tester are nominal values.

CAUTION! Danger to life due to electric shock!

• Only use the voltage tester to detect voltage.
• Use the voltage tester exclusively for the voltage range from 125 to 250 V AC.
• Do not use a faulty voltage tester with obviously compromised operation and/or safety.
• Only use the voltage tester in dry surroundings.
• Do not use the voltage tester in wet environments, e. g. when exposed to vapour or rain.

CAUTION! Never use the voltage tester as a screwdriver on live parts of an installation.

Prior to each use:

1. Check the insulating sleeve of the voltage tester for damage. Do not use it, if it is damaged.
2. Check whether the lamp on the voltage tester lights up by using a connected socket. Dispose of a damaged or defective voltage tester

WARNING! The fact that the indicator light is not visible does not guarantee the absence of voltage. The following factors may affect your ability to see the indicator light:

• unfavourable lighting conditions, for example, sun-shine
• temperatures outside the range of -10 °C bis +50 °C
• frequencies outside the range of 50 to 500 Hz
• unfavourable locations such as on wooden ladders, insulating floor coverings and in non-operationally grounded AC voltage networks

To test whether alternating current is present, car-ry out the following steps:

1. Hold the tip of the voltage tester against a contact of an electrical cable and
2. Touch the other end of the voltage tester with one finger.
   • If alternating current is present, the lamp will light up.

Cleaning and storage

Cleaning
Risk of damage!
If the trolley is not cleaned properly it may become damaged.

• Do not use an aggressive, abrasive cleaning agent and do not use a solvent, acid or chlorine based cleaning agent.
• Do not use brushes with metallic or nylon bristles and do not use sharp or metallic cleaning utensils such as blades, hard spatulas or similar.
• Use a mild cleaning agent to clean the trolley and a soft, clean towel. Allow the trolley to dry completely after cleaning.
• Remove lubricant and oil with a non-flammable cleaning agent.

Cleaning voltage tester
If the voltage tester is contaminated during normal use, it can be cleaned with a damp cloth and a household cleaner. Aggressive cleaning agents must not be used for cleaning.

Storage

Attention!
Rust could form if the trolley is stored in a damp location. The functionality or carrying capacity of the trolley could therefore be permanently and irreparably impaired.

• Protect the trolley from moisture, direct sunlight and frost.
• Store the trolley in a dry location.
• Keep the trolley away from children

Storage voltage tester

• Do not expose the voltage tester to direct sunlight.
• If the voltage tester is used in accordance with the operating manual, then no maintenance will be required.
• If the voltage tester does not function properly, send it to the service department for repairs.

Service information
Spare parts and accessories can be obtained from our service centre. To do this, scan the QR code on the cover page.

 Disposal and recycling

Notes for packaging

The packaging materials are recyclable. Please dispose of packaging in an environmentally friendly manner.

Notes on the electrical and electronic equipment act [ElektroG]
Waste electrical and electronic equipment does not belong in household waste, but must be collected and disposed of separately!

• Used batteries or rechargeable batteries that are not installed permanently in the old appliance must be removed non-destructively before disposal. Their disposal is regulated by the battery law.
• Owners or users of electrical and electronic devices are legally obliged to return them after use.
• The end user is responsible for deleting their per-sonal data from the old device being disposed of!
• The symbol of the crossed-out dustbin means that waste electrical and electronic equipment must not be disposed of with household waste.
• Waste electrical and electronic equipment can be handed in free of charge at the following places:
  • Public disposal or collection points (e.g. municipal works yards)
  • Points of sale of electrical appliances (stationary and online), provided that dealers are obliged to take them back or offer to do so voluntarily.
  • Up to three waste electrical devices per type of device, with an edge length of no more than 25 centimetres, can be returned free of charge to the manufacturer without prior purchase of a new device from the manufacturer or taken to another authorised collection point in your vicinity.
  • Further supplementary take-back conditions of the manufacturers and distributors can be obtained from the respective customer service.
• If the manufacturer delivers a new electrical appliance to a private household, the manufacturer can arrange for the free collection of the old electrical appliance upon request from the end user. Please contact the manufacturer’s customer service for this.
• These statements only apply to devices installed and sold in the countries of the European Union and which are subject to the European Directive 2012/19/EU. In countries outside the European Un-ion, different regulations may apply to the disposal of waste electrical and electronic equipment.

EU Declaration of Conformity

Translation of the original Declaration of Conformity
We declare under our sole responsibility that the product described here com-plies with the applicable directives and standards.

Warranty

Apparent defects must be notified within 8 days from the receipt of the goods. Otherwise, the buyer loses its rights of claim due to such defects are invalidated. We guarantee for our machines in case of proper treatment for the time of the statutory warranty period from delivery in such a way that we replace any machine part free of charge which provably becomes unusable due to faulty material or defects of fabrication within such period of time. With respect to parts not manufactured by us we only warrant insofar as we are entitled to warranty claims against the upstream suppliers. The costs for the installation of the new parts shall be borne by the buyer. The cancellation of sale or the reduction of purchase price as well as any other claims for damages shall be excluded.

www.scheppach.com

Frequently Asked Questions