scentify NEO Diffuser
Technical Specifications
| Model | scentify NEO DIFFUSER |
| Dimensions | 2.8 × 2.8 × 6.4 in |
| Oil capacity | 75 mL |
| Voltage | 100 – 240V ~ 50/60Hz |
| Power Consumption | 2.1W |
Safety Warnings & Guidelines
Read all instructions before using the product.
DANGER
- Use in environments between -10°C and 50°C only. Operation outside this range may damage the product and cause safety hazards. For use below 2000m altitude only.
- Use only the specified rated voltage. Otherwise, safety risks may occur.
- Do not expose battery pack or appliance to fire or excessive temperature.
WARNING
- Use only the recommended vaporizing medium. Other substances may produce toxic gases or pose a fire risk.
- Use only in conjunction with the supplied power supply device.
- Use only the safe ultra-low voltage specified by the appliance to prevent malfunction.
- If the supply cord is damaged, replace it with a special cord or assembly available from the manufacturer or service agent only.
- Rechargeable batteries may only be replaced by qualified personnel (dry batteries excepted).
- Do not tamper with original operating devices or functions.
CAUTION
- Not intended for persons with reduced physical, sensory, or mental capabilities, or lack of experience/knowledge (including children), unless supervised.
- Children should be supervised to ensure they do not play with the appliance.
- If equipped with a battery at the end of its service life, recycle and dispose of properly in accordance with local regulations.
This product is intended for sale and application in a business environment.
RED Article 10 (2): This product can be used across EU member states.
RED Article 10 (10): The RF distance between body and product is 20cm.
- Frequency Range: 2402-2480MHz
- Max. RF Output Power: -1.92 dBm
FCC Compliance Statement
Compliance Statements
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
RF Exposure
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
ISED / Canada Compliance Statement
- This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
- The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).
- This device meets the exemption from the routine evaluation limits in section 6.3 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
- This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Installing the Fragrance Cartridge
- Remove the cartridge cap: Twist the cartridge cap counterclockwise to remove. Keep the cap for future storage or transport.
- NOTE: Keep the cap for future storage or transport.
- NOTE: Keep the cap for future storage or transport.
- Insert the cartridge: Place the cartridge into the slot with the pins facing the back.
Controls and Operation
Button Controls
Power
Press and hold for 3 seconds to turn the diffuser on or off.
Adjust Intensity
- Press + to increase intensity.
- Press – to decrease intensity.
Ambient Lighting
Short press the power button to cycle through light colors.
Factory Reset
Press and hold both + and – buttons simultaneously to restore factory settings.
Intensity Levels
| Level | Sprays | Pauses |
|---|---|---|
| 1 | 5 sec | 5 min |
| 2 | 5 sec | 4 min |
| 3 | 5 sec | 3 min |
| 4 | 5 sec | 2 min |
App Connection and Guide
(Bluetooth Only – This device does not support Wi-Fi or cellular connections)
- 1. Open the app and select Bluetooth (this device does not support Wi-Fi or cellular connections) .
- Select your diffuser.
- Enter the default password: 8888 , press Login , and check Remember Password (optional).
Device Control: - Tap the device name or label to edit it. (be Save after sure to press each change)
- Select a schedule to edit. (you can create up to 5 schedules using the + button; swipe left to delete a schedule; use the toggle to enable or disable any schedule)
Use the power button to turn the diffuser on or off- Enable Smart Mode to run the diffuser only when the room is lit.
Schedule Settings: - Set the hours of the day you want the diffuser to operate by scrolling through the hour, minute, and AM/ PM.
- Tap to select the days you want the diffuser to run (all days are selected by default).
- Adjust the diffuser’s light color and brightness.
- To change the password, go to the About tab on the Device Control page and select Change the Password.
- Press and hold both + and – buttons simultaneously to restore factory settings.
- Need Additional Help? Contact support at info@scentify.com.
Documents / Resources
 | NEO Diffuser |
References
- qrgo.is/c86969d5qrgo.is
- scentify.comscentify.com
- User Manualmanual.tools