Thank you

If our product meets your expectations, share your opinion with other people on the portal ceneo.pl, social media or on the website of the store where you made the purchase. If you want to show our device on SAVIO Facebook Page, we will be very pleased.

If there is something that we could improve on our products, please write to us at support@savio.net.pl.

Package content

• SAVIO CT-01/W / CT-01/B Temperature and humidity sensor
• CR2032 battery
• User manual

Product diagram

1. Temperature indicator (ºC / ºF)
2. Humidity indicator
3. Comfort zone indicator
4. Time (AM / PM) / Year
5. Date
6. Built-in magnet with metal plate on 3M sticker
7. Adjustable stand (0 – 90 degrees)
8. SET button
9. – button
10. + button
11. Battery compartment
    

Instructions for use

1. Remove the plastic stopper from the battery compartment to activate the sensor. CR2032 battery is already inside.
2. LCD screen will be fully displayed for 5 seconds, after that it will present current indoor temperature and humidity, default time is set to 12:00, date is set to January 1st 2022.
3. To adjust time and date press SET button for 3s, the hour indicator will start flashing, press + or – but on to adjust the hour value or press and hold + or – for quick adjustment. After that, press SET button to move to the next adjustable field. If no change is made within 30s the device will automatically return to previously set values.
4. The setting sequence is shown as follow: Hour → Minute → Year → Month → Day → Save. Each sequence is adjusted using + or – button. Any change in the displayed information is confirmed by pressing SET button.
5. To change between 12 / 24 H modes, press – button.
6. To change between ºC / ºF, press + button.

The sensor is equipped with visual comfort zone indicator

1. When the humidity is lower than 40% the arrow will be fixed in red field (DRY).
2. 1When the humidity is in 40 – 69% range, the arrow will be fixed in green field (COMFORT).
3. When the humidity is in 70 – 99% range, the arrow will be fixed in blue field (WET).

Mounting the device

There are three ways to mount the device:

1. Put it on flat surface, adjust the angle of the stand.
2. Stick it to any metal surface (the device will stick to the surface thanks to a magnet that is placed inside the plastic shell).
3. Remove the foil from the 3M sticker on the additional metal sheet and stick it to the wall (surface must be clean), then put the sensor on the metal sheet stuck on the wall.

Important information

1. If the device turns off, insert new battery.
2. After starting the sensor, it takes several minutes to correctly read the air temperature and humidity (holding the sensor in hands will cause higher reading of temperature and humidity).

Technical specification

• Display: Temperature (ºC / ºF), humidity, comfort zone indicator, time, date
• Temperature range: -10ºC – 50ºC (± 1ºC)
• Humidity range: 10 – 99% (± 5%)
• Time display format: 12 h / 24 h
• Battery: CR2032, 3 V (included)
• Dimensions: 70 × 70 × 14 mm
• Color: White / Black

Safety conditions

• Use the product in accordance with its intended use, as improper use may damage the product.
• Do not expose the device to moisture, heat or sunlight, do not use the product in a dusty environment.
• The device should be cleaned only with a dry cloth.
• Independent repairs and modification result automatic loss of the warranty.
• Hitting or dropping may damage the product.

Warranty

The warranty covers a period of 24 months. Independent repairs and modifications result in automatic loss of the warranty. Warranty card is available for download on our website: www.savio.net.pl/en/service.

Information of the utilization of electrical and electronic equipment

This symbol indicates that electrical appliances should not be discarded with other household waste. Used equipment should be handed over to a local collection point for this type of waste or to a recycling center. Please contact your local authorities for information about disposal methods available in your area. Waste electrical equipment may contain hazardous substances (e.g. mercury, lead, cadmium, chromium, phthalates) which can get into air, soil and groundwater when leaking from used appliances. Environmental pollution with these substances leads to their bioaccumulation, causing lesion of disease in living organisms, which would pose a risk to human and animal health or life. Households may contribute to environmental protection by proper waste collection. In such way, hazardous substances from the equipment are neutralized and valuable secondary raw materials are reused for production of new equipment.

Information for customers and contractors and communication regarding complaints:

Pursuant to Article 13 section 1 and 2 of the General Data Protection Regulation (EU) 2016/679 of the European Parliament and of the Council of 27 April 2016 (hereinafter referred to as GDPR), please be advised that Elmak Sp. z o.o., with its registered seat at ul. Morgowa 81; 35-323 Rzeszów becomes the Administrator of your personal data. The Specialist for General Data Protection (SODO) can be contacted in writing to: SODO, Elmak Sp. z o.o., ul. Morgowa 81; 35-323 Rzeszów, via e-mail address: sodo@elmak.pl, and by phone at +48 (17) 854 98 14. Your personal data will be processed in order to perform the contract, in accordance with Article 6(1)(b) of the aforementioned regulation, to the extent resulting from tax laws and financial regulations. Recipients of your personal data include entities authorized by legal regulations to obtain personal data as well as processing entities providing services to Elmak Sp. z o.o. Your personal data will be stored on the basis of Administrator’s legitimate interest. You have the right to access your data, and the right to rectify, delete or limit processing of your data. You have the right to lodge a complaint to the supervisory body if you believe that the processing violates the GDPR. The provision of personal data is voluntary, however, a failure to provide such data may result in a refusal to conclude or in termination of a contract. Your personal data will not be subjected to automated decision making, including profiling referred to in Article 22 section 1 and 4 of the GDPR of April 27, 2016.

CUSTOMER SUPPORT

PRODUCER:
Elmak Sp. z o.o.
ul. Morgowa 81
35-323 Rzeszow
www.savio.net.pl