Sauermann group Si-CPE320 Flush Mounted Multifunction Sensor Transmitter User Guide

Make a cutting of 200 x 82 mm in the wall.
Drill 4 holes around the cutting as shown.
Insert the transmitter into the wall and fix it with the 4 screws provided.
Ensure IP66 protection by using silicone sealant between the wall and the transmitter.

Connections
Make electrical connections as per NFC15-100 standard:

Connections must be made by a qualified technician.
The transmitter should not be energized during connections.

First Start-Up:
Follow these steps to start up the transmitter:

Select your language and tap ‘Next’.
Set your time and time zone.
Connect the probe(s) before configuring the channel(s).

Quick Start Guide
These operating instructions describe the basic handling of the device.
Please refer to the operating instructions available at sauermanngroup.com for safe use of the product and detailed information.
Do not give this device to a child.

Symbols used
For your safety and in order to avoid any damage of the device, please read carefully the notes preceded by the following symbol:
Description of the device, operating temperature, protection of the instruments and information about storage
The Si-CPE320 is a transmitter that can measure simultaneous parameters including differential pressure, temperature (Pt100 and thermocouple), hygrometry, air quality (CO/CO2/VOC), air velocity, and airflow.
- Operating temperature: -10 to 50°C (14 to 122°F)
- Protection: IP66, resistant to VHP*
- Storage temperature: -10 to 70°C (14 to 158°F)

Directive 2014/53/EU
Hereby, Sauermann Industrie SAS declares that the radio equipment type Si-CPEC320 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: sauermanngroup.com

Mounting
To install a transmitter on a wall, make a cutting of 200 x 82 mm in the wall. Then drill 4 holes around the cutting as shown beside. Insert the transmitter into the wall and fix it with the 4 screws
(supplied with the transmitter).

To ensure IP66 protection, use sealant of silicone type between the wall and the transmitter.
If VHP* is used, check that the seal is VHP resistant.

Connections

Electrical connections as per NFC15-100 standard
This connection must be made by a formed and qualified technician. Whilst making the connection, the transmitter must not be energized. The presence of a switch or a circuit breaker upstream the device is compulsory.

Power supply terminal block

First start-up

Probe connection/disconnection

Connect a probe to the Si-CPE320 transmitter

On the back of the transmitter, present the probe connector (a) with its arrow and padlock face to the transmitter connector (b).
Push in the probe connector (a) into the transmitter connector (b) until you hear a click. The probe is correctly connected.

Disconnect a probe from the Si-CPE320 transmitter

Turn the ring (c) of the probe connector to the left.
Pull the probe connector (a) away from the transmitter connector (b).

Set a channel

Connect a probe to set a channel and tap ‘’Next’’.
The list of available channel is displayed. Tap the required channel
Tap ‘’PROBE 1’’ or ‘’MODULE’’. Parameters to set are now available.
Set the parameters according to your needs then tap the back arrow on the top left.
Channel two is configured. Tap next to configure outputs.

Set an output

Tap the output to set corresponding to the previously configured channel.
Activate the output taping .
Set the output type and high and low range values then tap the back arrow on the top left.
Tap ‘’Next’’ to dis-play measures.

Maintenance

Please avoid any aggressive solvents. Please protect the transmitter and its probes from any cleaning product containing formalin, that may be used for cleaning rooms or ducts.

Precautions for use
Please always use the device in accordance with its intended use and within parameters described in the user manual in order not to compromise the protection ensured by the device.

Make the most of your device’s capabilities by downloading the app.

Access all documentation about the device.

Customer service portal

Kimo, a Sauermann brand.
sauermanngroup.com
Sauermann Industrie
ZA Bernard Moulinet
+33 (0)5 53 80 85 00
services@sauermanngroup.com

FAQ

Q: How do I ensure IP66 protection during installation?
A: Use silicone sealant between the wall and the transmitter to ensure IP66 protection.

Q: Can I make electrical connections myself?
A: No, electrical connections must be made by a formed and qualified technician.

Documents / Resources

Sauermann group Si-CPE320 Flush Mounted Multifunction Sensor Transmitter [pdf] User Guide
KIMO, Si-CPE320 Flush Mounted Multifunction Sensor Transmitter, Si-CPE320, Flush Mounted Multifunction Sensor Transmitter, Mounted Multifunction Sensor Transmitter, Multifunction Sensor Transmitter, Sensor Transmitter, Transmitter

References

User Manual

Sauermann group Si-CPE320 Flush Mounted Multifunction Sensor Transmitter

Product Information

Product Usage Instructions