RYNOSKIN - logo

PYTHON SIDE STEP
PART NO. RSSS-FB2D-57
FITS: 2021-Up Ford Bronco 2 Door

RYNOSKIN RSSS FB2D 57 Running Boards Side Steps - icon 90-180 min
RYNOSKIN RSSS FB2D 57 Running Boards Side Steps - icon1 Cutting Not Required
RYNOSKIN RSSS FB2D 57 Running Boards Side Steps - icon2 Drilling Not Required

Torque & Tools

Fastener
Size
Tightening Torque (ft-lbs)

Wrench Required

Allen Wrench
Required
▢  6mm ▢ 7-8.5 RYNOSKIN RSSS FB2D 57 Running Boards Side Steps - icon3 ▢ 10mm RYNOSKIN RSSS FB2D 57 Running Boards Side Steps - icon4 L 4mm
■ 8mm ■ 18-20 ■ 13mm ▢ 5mm
■ 10mm ■ 35-40 ■ 16mm ▢ 6mm
▢ 12mm ▢ 60-70 ▢ 18mm ▢ 8mm

BEFORE INSTALLATION

REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT
DEPEND ON THE PARTS LIST. READ INSTRUCTIONS CAREFULLY. CUTTING
MAY BE REQUIRED. ASSISTANCE IS RECOMMENDED.

Part List

RYNOSKIN RSSS FB2D 57 Running Boards Side Steps -

RYNOSKIN RSSS FB2D 57 Running Boards Side Steps - fig1

PLEASE NOTE THAT THE FOLLOWING
PICTURES ARE BASED ON THE
PASSENGER SIDE INSTALLATION
STEP 1
Starting from underneath the Passenger/Right body panel, locate the front mounting location and the threaded holes in the body panel, (Fig 1). Remove the plastic plugs covering the holes.

RYNOSKIN RSSS FB2D 57 Running Boards Side Steps - fig2

(Fig 1) Passenger/Right front mounting location
STEP 2
Select the Passenger/Right Front Mounting Bracket. Attach the Mounting Bracket to the front location with (2) 10mm Hex Bolts, (2) 10mm Lock Washers and (2) 10mm Flat Washers, (Fig 2). Do not tighten hardware.

RYNOSKIN RSSS FB2D 57 Running Boards Side Steps - fig3

(Fig 2) Attach the Passenger/Right Front Mounting Bracket to the front location
STEP 3
Repeat Steps 1-2 to attach (1) Passenger/Right Rear Mounting Brackets to the rear locations, (Figs 3-4). Do not tighten hardware.

RYNOSKIN RSSS FB2D 57 Running Boards Side Steps - fig4

(Fig 3) Passenger/Right rear mounting location

RYNOSKIN RSSS FB2D 57 Running Boards Side Steps - fig5

(Fig 4) Attach (1) Passenger/Right Rear Mounting Bracket to the rear location.
STEP 4
Select the Passenger/Right Running Board.
NOTE: The Passenger/Right Running Board will have a “57-P” on the front. Carefully place Running Board on the brackets. Attach Running Board to the (3) Mounting Brackets with (6) 8mm Combo Bolts, (Fig 5). Do not tighten hardware.

RYNOSKIN RSSS FB2D 57 Running Boards Side Steps - fig6

(Fig 5) Attach the Passenger/Right Running Board to the Mounting Brackets
STEP 5
Level and adjust the Running Board and fully tighten all hardware.
STEP 6
Repeat Steps 1—5 to attach the Driver/Left Running Board.
STEP 7
Do periodic inspections to the installation to make sure that all hardware is secure and tight.
Attention
To protect your investment, do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used also to clean the Running Boards.

RYNOSKIN - logowww.rynoskinauto.com
Customer Support: service@rynoskinauto.com
6/2/23 (JH)

Documents / Resources

RYNOSKIN RSSS-FB2D-57 Running Boards Side Steps [pdf] Owner's Manual
RSSS-FB2D-57 Running Boards Side Steps, RSSS-FB2D-57, Running Boards Side Steps, Boards Side Steps, Side Steps

References

Leave a comment

Your email address will not be published. Required fields are marked *