Ritesdepot Remote Controlled LED Module
Product Overview
This 85mm diameter wireless, rechargeable mood light uses an RF remote to provide RGBW color changing with dimmable brightness. It’s designed for indoor ambient lighting such as bedroom night lights, furniture mood lighting, and party decorations.
Specifications
| Parameter | Specification |
|---|---|
| Diameter | 85mm |
| Power Source | Built-in rechargeable battery (USB charging) |
| Battery Life | Up to 8–15 hours (depending on brightness/color mode) |
| Charging Time | 2–3 hours (full charge) |
| Light Color | RGBW (16 million colors + warm white) |
| Control Range | Up to 10 meters (30ft, no line of sight required) |
| Working Temperature | -10°C ~ 45°C |
| Waterproof Level | IP20 (Indoor use only) |
Quick Setup & Use
- Charge the light: connect the included USB cable to a 5V USB adapter. The light will indicate status with red (charging) and green (fully charged).
- Unplug the charger once fully charged.
- Turn the light on/off using the remote’s ON/OFF button.
- Select lighting modes and color using the remote (static colors, RGB mixing, flash/strobe, fade/gradient, or warm white).
- Adjust brightness with the Brightness +/- buttons.
- Use the Timer button to set auto-off (1H / 2H / 4H / 8H) and the Memory button to save current settings..
- 1 x LED Light Module (85mm diameter)
- 1 x 24-Key RF Remote Controller
- 1 x USB Charging Cable
- 1 x User Manual
Safety Precautions⚠ WARNING: Risk of electric shock or fire hazard.
- Do not submerge in water – this unit is not waterproof.
- Use only with a 5V USB power adapter (not included). Do not connect to 12V car power directly.
- Do not disassemble the unit. Opening will void the warranty and risk electric shock.
- Keep away from children under 3 years (small parts/choking hazard).
- Dispose of properly – do not burn or incinerate the battery.
Charging Instructions
- Locate the micro-USB charging port on the base of the light module.
- Connect the included USB cable to a 5V USB adapter (phone charger/laptop).
- The light will turn on during charging (red light = charging; green light = fully charged).
- Unplug once fully charged for wireless use.
| Button/Mode | Function |
|---|---|
| ON/OFF | Turn the light on/off |
| Color Selection (16 Colors) | Switch to static colors (red, green, blue, white, etc.) |
| RGB Mix | Create custom colors by mixing RGB |
| Brightness +/- | Adjust light intensity (10 levels: 10% – 100%) |
| Speed +/- | Adjust the speed of fading/flashing effects |
| Flash/Strobe | Rapid color changing or flashing mode |
| Fade/Gradient | Smooth transition between colors |
| Warm White | Switch to constant warm white light (normal night light mode) |
| Timer | Set auto-off time (1H / 2H / 4H / 8H) |
| Memory | Save your current color/brightness settings |
Pairing / Re-pairing Guide
If the remote stops controlling the light:
- Turn the light on using the power button.
- Press and hold the “Pair” button (usually the “Dimmer +” or a specific key) on the remote for 3-5 seconds.
- The light will flash briefly to confirm successful pairing
Maintenance & Care
- Cleaning: Wipe the surface with a soft, dry cloth. Do not use abrasive cleaners or water on the electronics.
- Storage: Store in a cool, dry place. If not in use for long periods, recharge every 3 months to preserve battery life.
- Battery Life: Recharge when the light becomes noticeably dimmer to extend battery health.
Warranty Information
- Warranty: 12-month limited warranty against manufacturing defects.
- Coverage: Includes replacement for faulty lights or remotes.
- Exclusions: Damage from misuse, water exposure, or unauthorized repair is not covered.
- Support: For assistance, contact our customer service with your order number.
Troubleshooting
| Issue | Possible Cause | Solution |
|---|---|---|
| Light won’t turn on | 1) Battery is dead 2) Remote battery is low |
1) Charge the LED module fully 2) Replace remote battery (CR2025/CR2032) |
| Remote not working | 1) Remote not paired 2) Out of range |
1) Ensure remote is paired (see Pairing / Re-pairing Guide) 2) Move within 10 meters of the light |
| Light dims quickly | 1) Battery power is low 2) Brightness set too high |
1) Recharge the unit 2) Lower brightness via the remote |
| Colors are incorrect | 1) Remote signal interference | Move the remote closer, or re-pair the device |
Pairing / Re-pairing (if remote stops controlling the light): Turn the light on, then press and hold the Pair button on the remote for 3–5 seconds. The light will flash briefly to confirm successful pairing.
Documents / Resources
 | Remote Controlled LED Module |
References
- User Manualmanual.tools
Published: August 13, 2026