Reolink D340W Video Doorbell Instruction Manual

Step 3
Launch the Reolink App. Click the “ ” button in the top right corner
and scan the QR code on the doorbell and follow the onscreen
instructions to finish the initial setup.

Set up the Doorbell on PC (Optional)

Step 1
Download and install the Reolink Client. Go to https://reolink.com >
Support > App & Client

Step 2
Power on the video doorbell.

Step 3
Launch the Reolink Client. Click the “ ” button and input the UID
number of the doorbell to add it.

Step 4
Follow the onscreen instructions to finish the initial setup.

Install the Doorbell

Step 1
Put the mounting hole template on the wall by the door and drill holes as shown.

Step 2
Install the mounting plate using the long screws provided through the two holes.

Step 3
Run the power adapter through the mounting plate and the hole on
the wall to connect it to the doorbell, then attach the doorbell to the
plate.

Step 4
Plug the power adapter into a socket near the door. Use the long
power extension cable if the socket is too far away from your
doorbell.

NOTE: Reolink Video Doorbell PoE&Wi-Fi can also be powered by the
existing doorbell wiring system. In such case, you are required to first
bypass the existing mechanical chime with the jumper cable to get
sufficient power. Without sufficient power, the doorbell may restart
and has an unstable connection, and the mechanical chime may
vibrate and generate noise. If the wire is not long enough, use the
extension cable, as shown below. After the installation, the existing
mechanical chime will not ring anymore. Use the extension cable
to extend the length of the existing power cable for the doorbell, as
shown below.

Install a Wedge (Optional)

If you need to adjust the angle of the doorbell, you can use the
wedge provided. (The Reolink Video Doorbell PoE is taken as an example)

Step 1
Put the mounting hole template on the wall and drill holes as shown.

Step 2
Install the wedge using the screws provided through the two holes.
Ensure that the notched side of the wedge is facing outside.

Step 3
Screw the mounting plate to the wedge.

Step 4
Run the Ethernet cable through the wedge and mounting plate, and
attach the doorbell to the plate.

Remove the Doorbell

If you want to remove the doorbell from the mounting plate, you
may use the reset needle to poke the bottom.

Specifications

Field of View:
Black Version: 135° Horizontal, 100° Vertical, 180° Diagonal
White Version: 100° Horizontal, 135° Vertical, 180° Diagonal
Operating Temperature: -10° C – +50° C (14° F – 122° F)
Dimension: 133 x 48 x 23mm
Weight: 96g

Important Safety Instructions

Please read the instructions carefully before using the device.

Replace only with the same or equivalent type of accessories recommended
by Reolink.
Do not use the device in an environment that exceeds the recommended
temperature range.
Do not use the device in an environment that exceeds the recommended
humidity range.
Do not attempt to disassemble, repair, or alter the device by yourself.
Always follow the local safety laws and regulations when using the device.
The device contains (or comes with) small components, small plastic
elements, and other small parts that may cause choking hazards. Keep
the device and its accessories out of reach of children. Consult a physician
immediately if small parts are swallowed.
The device contains (or comes with) cables or cords that may cause
strangulation hazards. Keep the device and its accessories out of reach of
children.

Legal Disclaimer

To the maximum extent permitted by applicable law, this document
and the product described, with its hardware, software, firmware,
and services, are delivered on an “as-is” and “as-available” basis,
with all faults and without warranty of any kind. Reolink disclaims all
warranties, express or implied, including but not limited to, warranties
of merchantability, satisfactory quality, fitness for a particular purpose,
accuracy, and non-infringement of third-party rights. In no event will
Reolink, its directors, officers, employees, or agents be liable to you for
any special, consequential, incidental or indirect damages, including but
not limited to damages for loss of business profits, business interruption,
or loss of data or documentation, in connection with the use of this
product, even if Reolink has been advised of the possibility of such
damages.

To the extent permitted by applicable law, your use of the Reolink
products and services is at your sole risk and you assume all
risks associated with internet access. Reolink does not take any
responsibilities for abnormal operation, privacy leakage or other
damages resulting from cyber attacks, hacker attacks, virus inspections,
or other internet security risks. However, Reolink will provide timely
technical support if required.

The laws and regulations related to this product vary by jurisdiction.
Please check all relevant laws and regulations in your jurisdiction before
using this product to ensure that your use conforms to the applicable
law and regulation. During the use of the product, you must comply with
relevant local laws and regulations. Reolink is not responsible for any
illegal or improper use and its consequences. Reolink is not liable in the
event that this product is used with illegitimate purposes, such as thirdparty
rights infringement, medical treatment, safety equipment, or other
situations where the product failure could lead to death or personal
injury, or for weapons of mass destruction, chemical and biological
weapons, nuclear explosion, and any unsafe nuclear energy uses or
anti-humanity purposes. In the event of any conflicts between this
manual and the applicable law, the latter prevails.

Notification of Compliance

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation. Changes or
modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses
and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your
body.

ISED Statement

This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that
may cause undesired operation of the device.”

This equipment should be installed and operated with a minumum
distance of 20 cm between the radiator and your body.

MODIFICATION: Any changes or modifications not expressly approved by
the grantee of this device could void the user’s authority to operate the
device.

This Class B digital apparatus complies with Canadian ICES-003.

Operation of 5150-5350 MHz is restricted to indoor use only.

SIMPLIFIED EU AND UK DECLARATION OF CONFORMITY

Hereby, REOLINK INNOVATION LIMITED declares that the radio equipment
type [refer to the cover of the Operational Instructions] is in compliance
with Directive 2014/53/EU.The full text of the EU and UK declaration of
conformity is available at the following internet address: https://support.
reolink.com/hc/en-us/articles/36788378727065/
RF exposure information: The Maximum Permissible Exposure (MPE)
level has been calculated based on a distance of 20cm between the
device and the human body. To maintain compliance with RF exposure
requirement, use product that maintain a 20cm distance between the
device and human body.

Wi-Fi Operating Frequency

Operating Frequency :
2412~2472MHz RF Power: ≤20dBm(EIRP)
5150~5250MHz RF Power: ≤23dBm(EIRP)
5250~5350MHz RF Power: ≤23dBm(EIRP)
5470~5725MHz RF Power: ≤23dBm(EIRP)
5725~5875MHz RF Power: ≤14dBm(EIRP)
868MHz RF Power: ≤13.9dBm(EIRP)

The functions of Wireless Access Systems including Radio Local
Area Networks(WAS/RLANs) within the band 5150-5350 MHz for this
device are restricted to indoor use only within all European Union
countries
(BE/BG/CZ/DK/DE/EE/IE/EL/ES/FR/HR/IT/CY/LV/LT/LU/HU/MT/NL/AT/PL/PT/
RO/SI/SK/FI/SE/TR/NO/CH/IS/LI/UK(NI)

Correct Disposal of This Product

This marking indicates that this product should not be disposed
with other household wastes throughout the EU. To prevent possible
harm to the environment or human health from uncontrolled waste
disposal, recycle it responsibly to promote the sustainable reuse of
material resources. To return your used device, please use the return
and collection systems or contact the retailer where the product
was purchased. They can take this product for environmentally safe
recycling.

(a)the equipment does not have a standby mode or other equivalent
state in terms of energy efficiency requirements, power management
function or the ability to deactivate wireless network connections
mode;
(b)the power consumption of the equipment is likely to be higher than
other equipment models meeting these functional requirements.

Limited Warranty

This product comes with a 2-year limited warranty that is valid only if
purchased from Reolink Official Store or a Reolink authorized reseller.
Learn more: https://reolink.com/warranty-and-return/.

NOTE: We hope that you enjoy the new purchase. But if you are not
satisfied with the product and plan to return, we strongly suggest
that you reset the camera to factory default settings and take out the
inserted SD card before returning.

Terms and Privacy

Use of the product is subject to your agreement to the Terms of Service
and Privacy Policy at reolink.com

Terms of Service
By using the Product Software that is embedded on the Reolink product,
you agree to the terms&conditions between you and Reolink. Learn
more: https://reolink.com/terms-conditions/

Technical Support

If you need any technical help, please visit our official support site and
contact our support team before returning the products,
https://support.reolink.com.

Trademarks Acknowledgement

“Reolink” and other Reolink’s trademarks and logos are the properties
of Reolink. Other trademarks and logos mentioned are the properties of
their respective owners.

REOLINK INNOVATION LIMITED
FLAT/RM 705 7/F FA YUEN COMMERCIAL BUILDING 75-77 FA YUEN STREET
MONG KOK KL HONG KONG

Documents / Resources

Reolink D340W Video Doorbell [pdf] Instruction Manual
D340W, D340W Video Doorbell, Video Doorbell, Doorbell

References

User Manual

D340W Video Doorbell

Operational Instructions
Apply to: D340W

What’s in the Box

Doorbell Introduction

Set up the Doorbell