INSTALLATION GUIDE
N4-RS84-3 Shelving ( steel )
Transit Low Roof
Nissan NV Low Roof GM Savana
N4-RS84-3 Shelving
REQUIRED ITEMS
- Cordless Impact
- Cordless Drill
- Tape Measure
- Marker
- 1/2″ Socket
- 1/2″ Drill Bit w/ Drill Collar ( Set at 1/2″ )
- 3/8″ Driver Bit
- Knife
- Plusnut Tool / Plusnut Gun ( 5/16″ )
PHASE 1 – ASSEMBLY
1.1 SETUP
1.1.1 Unpack components; compare with the bill of materials.
1.1.2 Verify all parts are present.
BILL OF MATERIALS
| Item No. | Description | Qty. |
| 40 – 725 | Center Post, Low roof | 1 |
| 40 – 715 | Bracket head | 2 |
| 40 – 716 | Bracket arm | 2 |
| 40 – 7110 | End Panel ( Left ) | 1 |
| 40 – 7120 | End Panel ( Right ) | 1 |
| 60 – 11.875 × 84 | Shelf Tray, Black Plywood, Usable 12″ × 84″ | 1 |
| 60 – 13.875 × 84 | Shelf Tray, Black Plywood, Usable 14″ × 84″ | 2 |
| 94 – 4028 | Assembly Fastener Kit | 1 |
| 96 – 4028 | Install Fastener Kit | 1 |
1.1.3Fastener kits.
| 94 – 4028 Fastener Kit |  |
Fastener Assembly |
| 8× |  |
# 90-204 | Hex Bolt 5/16″-18 × 3/4″ GR-5 ZINC |
| 6× |  |
# 92-200 | Screw HFH #10 – 16 × 3/4″ ZINC |
| 24× |  |
# 92-102 | Screw HWH #14 × 1″ ZINC |
| 8× |  |
# 94-116 | Serrated Nut 5/16″-18 ZINC |
| 8× |  |
# 98-116 | Flat Washer 5/16″ – 18 × 1″ ZINC |
| 96 – 4028 Fastener Kit | |
Fastener Assembly |
| 6× | |
# 90-011 | Hex Bolt 5/16″-18 × 1-3/4″ GR-5 ZINC |
| 4× |  |
# 90-212 | Hex Bolt 5/16″-18 × 1-1/4″ GR-5 ZINC |
| 10× |  |
# 94-132 | Plusnut |
| 10× |  |
# 98-116 | Flat Washer 5/16″, O.D. 7/8″ ZINC |
| 10× |  |
# 98-122 | Lock Washer 5/16″ ZINC |
| 6× |  |
# 98-157 | Spacer 0.375″ ID, × 1.0″ OD × 0.25″ LONG NYLON |
PHASE 1 – ASSEMBLY
1.2 SHELF ASSEMBLY
1.2.1 Attach both panels to the shelf trays.
NOTE: You can adjust the bottom shelf location to maximize or minimize your space over the wheel.
IMPORTANT: Always handle panels on a smooth, protected and clean surface to avoid unnecessary scratching.
1.2.2 Attach the center post to the center front face of the shelf.
1.2.3 Attach the bracket head to the bracket arm.
NOTE: Hand-tighten the bolts for adjustment.
PHASE 2 – INSTALLATION
2.1 ATTACH WALL BRACKETS TO THE END PANELS
2.1.1 • Lift the assembled shelf to the vehicle, then put it in place.
- Attach the bracket arm to the panels aligning the bracket head to the horizontal rim of the vehicle.
NOTE: Handle with care.
PHASE 2 – INSTALLATION
2.2 MARK HOLES FOR PLUS NUTS
2.2.1 After attaching the brackets mark the holes on the brackets, end panels and center post to the vehicle.
PHASE 2 – INSTALLATION
2.3 ATTACH PLUS NUTS
2.3.1 • Lift the assembled shelf on the side.
- Drill all the marks using a 1/2″ drill bit w/ drill collar, then attach plus nuts to the
NOTE: Use a 1/2″ drill bit with a drill collar to stop the drill at 1/2″ depth.
WARNING: Before drilling, ensure that you will not hit any critical parts of the vehicle like the Gas tank, Wiring Harness and Hose.
2.3.2 How to attach plus nut.
- using Plusnet gun
STEP: Put the Plusnet on the plus nut gun, then attach the plus nut in the hole by turning the gun forward until the plus nut locks, then remove the gun by turning in reverse.
- using the 6491 plus nut tool
NOTE: The hardware used for the 6490 plus nut tool is not included in the fastener bag.
The 6490 plus nut tool can be ordered separately upon demand at no charge.
TOOLS
- Cordless Impact
- 1/2″ Socket
- 9/16″ Wrench
STEP 1: Assemble the 6491 plus nut tool with the hardware needed, plus the nut and the 9/16″ wrench as shown.
STEP 2: Attach the plus nut in the hole by turning the bolt forward using an impact with a 1/2″ socket until the Plusnet locks, then remove the bolt by turning the impact in
reverse.
PHASE 2 – INSTALLATION
2.4 ATTACH THE SHELF UNIT TO THE FLOOR
without ranger floor
2.4.1 Put the assembled shelf back in place aligning the holes to the plus nuts, then install the end panels and center post to the plus nuts.
WITH RANGER FLOOR
2.4.2 • Lift the shelving unit inside the van, then put it in place.
- Install the shelving unit to the floor mounting track by sliding bolts in the mounting tracks, and putting screw in the last rear slot of the end panels of the shelving unit.
PHASE 2 – INSTALLATION
2.5 ATTACH WALL BRACKETS
WITH RANGER FLOOR
2.5.1 Aligned the wall brackets to the plus nuts, then install the wall brackets to the wall.
NOTE: Tightened the bolts that used to attach the wall bracket to the wall or wall kits 1 st before the bolts that used to attach the wall bracket to the end panel.
IMPORTANT: After installation is completed, ensure all bolts are tightened.
2.5.2 Aligned the wall brackets to the wall mounting track kits, then install the wall brackets to the wall mounting track kits using channel nuts.
NOTE: Tightened the bolts that are used to attach the wall bracket to the wall or wall kits 1 st before the bolts that are used to attach the wall bracket to the end panel.
IMPORTANT: After installation is completed, ensure all bolts are tightened.
“You have successfully installed your
N4-RS84-3
Thank you for doing business with us.”
For any feedback or suggestions, you may have, please contact: cs@rangerdesign.com
For technical support, contact us at 1-800-565-5321
N4-RS84-3 Installation Guide | REV. B1
Documents / Resources
 |
RANGER N4-RS84-3 Shelving [pdf] Installation Guide N4-RS84-3 Shelving, N4-RS84-3, Shelving |
