The drivers don't seem to be compatible with Windows 11.
The manual for the j5Create USB-C Dual HDMI Mini Dock JCD381 lists compatibility with Windows 10 / 8.1 / 8 / 7. It does…
Manuals+ Q&A
Ethernet questions & answers
Browse answered questions about Ethernet, including setup, troubleshooting, compatibility and maintenance.
Browse topics
Answered questions
Is the ABLEWE 3-Port USB 3.0 Hub compatible with Windows 11, and are there separate drivers required?
The ABLEWE USB 3.0 to Ethernet Adapter is designed as a plug-and-play device. While the manual specifically lists compatibility up to Windows 10, it…
Does the ABLEWE USB 3.0 to Ethernet Adapter have a MAC address for network registration?
Yes, the ABLEWE USB 3.0 to Ethernet Adapter has a unique MAC address. Any hardware device that provides a network interface, such as this…
How do I install the UNI AE01 Ethernet LAN Network Adapter on my Windows 10 laptop?
Installing the UNI AE01 Ethernet LAN Network Adapter on a Windows 10 laptop is a straightforward process. Here's a step-by-step guide: 1. Plug the…
How do I connect the UtechSmart UCN3273 USB-C Ethernet Multiport Adapter to my device?
To connect the UtechSmart UCN3273 USB-C Ethernet Multiport Adapter to your device, follow these steps: 1. Locate an available USB-C port on your device.…
How do I install the LevelOne USB-0301 Fast Ethernet USB Network Adapter?
To install the LevelOne USB-0301 Fast Ethernet USB Network Adapter, follow these steps: 1. Ensure that your computer is powered on and running. 2.…
How do I connect the PmodNIC100 Ethernet Controller Module to my system board?
To connect the PmodNIC100 Ethernet Controller Module to your system board, you will need to follow these steps: 1. Identify the 12-pin Pmod connector…
How do I configure the Ewon Cosy+ for remote access to Ethernet devices using Talk2M?
To configure the Ewon Cosy+ for remote access to Ethernet devices using Talk2M, follow these steps: 1. Power on the Ewon Cosy+ and wait…
How do I connect the EZCast ER01/ET01/WR01/WT01 Ethernet Transmitter and Receiver to my devices?
To connect the EZCast ER01/ET01/WR01/WT01 Ethernet Transmitter and Receiver, follow these steps: 1. Position the toggle switch on both the transmitter (ET01/WT01) and receiver…
How to wire Easy Livin Distribution Creative Lighting Ethernet DALI-DMX Gateway?
To wire the Easy Livin Distribution CRE-EDIDIO-10-1D Creative Lighting Ethernet DALI-DMX Gateway, follow these steps: 1. Fasten the gateway onto a DIN rail. 2.…
How do I restore the SystemQ Ethernet Relay Controller to factory defaults?
To restore the SystemQ XREL019 Ethernet Relay Controller to factory defaults, follow these steps: 1. Remove the power supply from the relay controller. 2.…
How do I connect and configure the LANCOM XS-5116QF 16-Port 10-Gigabit Ethernet switch for initial setup?
To connect and configure the LANCOM XS-5116QF switch for initial setup, follow these steps based on the user guide: 1. Configuration Interfaces: Connect the…
How can I simulate the Triple-Speed Ethernet Intel FPGA IP design example testbench using different simulators?
To simulate the Triple-Speed Ethernet Intel FPGA IP design example testbench using different simulators, you can follow these steps as outlined in the user…
How do driver installation successful Mac computer SECOMP 12021107 USB 3.0 3 Port Hub Gigabit Etherne Adapter?
After installing the driver for the SECOMP 12021107 USB 3.0 3 Port Hub with Gigabit Ethernet Adapter on your Mac computer, you can follow…
How do I power the Altronix NetWaySP2P Series 3-Port Ethernet Over Fiber PoE+ Hardened Switches?
To power the Altronix NetWaySP2P Series switches, follow these steps: 1. **Powering NetWaySP2P/NetWaySP2PWPN:** - Connect a 48VDC-56VDC power source to the terminals marked [48-56VDC…
How do I connect and configure the QSFPTEK S5300-48T4X 48 Port Gigabit Ethernet L3 Switch?
To connect and configure the QSFPTEK S5300-48T4X 48 Port Gigabit Ethernet L3 Switch, follow these steps based on the provided manual: 1. **Connecting the…
How do I update the firmware on my DMXking eDMX1 MAX Ethernet ArtNet sACN DMX Adapter?
According to the user manual, updating the firmware on your DMXking eDMX1 MAX Ethernet ArtNet sACN DMX Adapter is a straightforward process. Here are…
How do I set up a hot link point-to-point connection using the TC1912 Ethernet Telephone Extender within a LAN?
**Step-by-Step Guide:** 1. **Equipment Needed:** - Two TC1912 units - Two regular analog telephone sets - Two telephone wires and two Ethernet cables 2.…