How do I map the X button to M1 and the Circle button to M2 on the BELOPERA Ymir controller?
To map specific buttons to the back paddles (M1 and M2) on your Ymir controller, follow these steps: Enter Mapping Mode: Long-press the Turbo…
Manuals+ Q&A
Controller questions & answers
Browse answered questions about Controller, including setup, troubleshooting, compatibility and maintenance.
Browse topics
Answered questions
Newest questionsHow do I map the X button to the M1 or M2 back buttons?
To map the X button to the M1 or M2 back buttons on your Ymir controller, follow these steps: Enter Mapping Mode: Long-press the…
How do I enable Auto Run mode, and why is the irrigation not starting at the set time?
To enable automatic irrigation, you must be in AUTO RUN mode. Press the MODE button repeatedly until the AUTO RUN screen (showing the current…
How can I connect the BIGBIG WON BLITZ2 controller to a Galaxy Tab using a wired connection?
To connect your BIGBIG WON BLITZ2 controller to a Galaxy Tab (Android) via a wired connection, follow these steps: Connection: Use a USB-C to…
How do I fix my GMB Gaming JPD-PS4BT-01 controller when it is stuck in Bootloader Mode and recognized as B23RUBOOT1.00?
If your GMB Gaming controller is stuck in Bootloader Mode (appearing as 'B23RUBOOT1.00'), it typically indicates a firmware corruption or a hardware state that…
How can I resolve the 'pa5' (Paus) code on my Rain Bird ESP-9V controller?
The code 'PAUS' (often read as 'pa5') on the Rain Bird ESP-9V indicates that the Delay Watering (Rain Delay) feature is active. This feature…
What software do I use to change the RGB settings on the GAM-139 controller?
Based on the user manual for the DELTACO GAMING GAM-139 Wireless Controller, there is no mention of a specific software application for controlling RGB…
How do I change the temperature display between Celsius and Fahrenheit on the Midea RG10A(B2S)/BGEF remote?
To alternate the temperature display between °C and °F on your Midea RG10A(B2S)/BGEF remote controller, follow these steps: Locate the TEMP Up (∧) and…
How do I switch the ABXY button layout between Xbox and Nintendo configurations on the YOUQI YQ-101 controller?
To switch the ABXY button layout between the Xbox and Nintendo configurations on the YOUQI YQ-101 Afterglow Wave Controller, press and hold the Set…
Why is my Felicity Solar MPPT3024 flashing a red fault light while the green light remains solid after sunset?
Based on the Felicity Solar MPPT User Guide, here is an analysis of your indicator lights and steps to resolve the issue: Indicator Meanings:…
How do I program a temperature profile with a ramp of 100°C/h to 620°C, a 2-hour soak, and a cooling ramp of 80°C/h on the Shinko BCS2?
To program a temperature profile (Program Control) on the Shinko BCS2, you must first enable Program Control and then define the steps in the…
How can I replace the PAD MODE lamps on my Pioneer DDJ-FLX6, and what is the cost?
The Pioneer DDJ-FLX6 instruction manual does not provide instructions for internal hardware repairs, such as replacing the LED lamps in the PAD MODE section.…
Why is my Y&H solar charge controller not displaying the panel voltage even though the panel is outputting 46V?
If your Y&H MPPT controller is not showing the panel voltage despite the panel outputting 46V, please check the following based on the installation…
How do I re-pair the RED5 Motion Control UFO with its remote control?
To re-pair your RED5 Motion Control UFO with the remote control, follow these steps based on the instruction manual: Power on the UFO: Connect…
How do I connect the MiBOXER FUT036 controller to the smartphone app without a remote or a reset button?
Based on the MiBOXER FUT036 manual, there is a critical requirement for smartphone connectivity that may be the cause of your trouble: the FUT036…
Why does my EasySMX X05Pro controller turn off by itself even when connected via USB, despite a firmware update?
If your EasySMX X05Pro continues to turn off automatically even when connected via USB and after a firmware update, please try the following troubleshooting…
How do I adjust the minimum and maximum cooling times on the NOVUS N150?
To adjust the cooling and compressor timing parameters on the NOVUS N150, you must enter the Configuration Cooling Cycle (CF.CL). Follow these steps: Press…
Where can I find detailed flight parameter explanations and setup instructions for the RadioMaster NEXUS-X?
The RadioMaster NEXUS-X Heli Flight Controller is designed to run on Rotorflight 2.2 firmware. Because the NEXUS-X is a hardware platform, the specific flight…
How do I set the opening and closing limit switches for the Dooya DD274B controller?
Based on the instruction manual for the Dooya DD274B Controller, this specific device is designed to work with motors that have mechanical limits. This…
How do I map the L3 button to the rear paddle buttons?
To map the L3 button to one of the rear paddles (Macro buttons) on your Fantech EOS PRO II WGP15V2, follow these steps using…
How can I get a replacement for my Beautyrest Microplush Heated Blanket under warranty if one side has stopped working?
The provided user guide for the Beautyrest Microplush Heated Blanket with WiFi Controller does not contain information regarding warranty claims or how to get…
Why is my LED Bluetooth Symphony Controller not being found by the app?
If your device cannot be found, please follow these troubleshooting steps from the manual: Check Power: Ensure the light strip is properly connected to…
How do I handle voltage drop when installing 200 feet of LED lights with the GOULY controller?
To handle voltage drop for a long installation like your 200-foot run, the GOULY LED Controller manual provides specific instructions under the Connection Diagram…
Is the DJI Osmo Action GPS Bluetooth Remote Controller compatible with the DJI Osmo Nano, and how do I get GPS data for my recordings?
Based on the official user guide, the Osmo Action GPS Bluetooth Remote Controller is primarily designed to connect to the Osmo Action 4. While…