Why does my pump only draw water when the controller is not installed, even after replacing the controller?
If your pump works alone but fails when the TOTAL TWPS101 controller is installed, the issue is likely related to air leaks, priming, or…
Manuals+ Q&A
Control questions & answers
Browse answered questions about Control, including setup, troubleshooting, compatibility and maintenance.
Browse topics
Answered questions
Newest questionsWhy are the anchor (spot lock) and heading lock functions not working on my Haswing 50806 remote control?
If your Haswing 50806 remote control operates basic steering and speed but the Anchor (Spot Lock) and Heading Lock functions are unresponsive, please check…
Which button is used to view teletext on the Meliconi Easytel 2 remote?
Based on the visual layout of the Meliconi Easytel 2 remote control shown in the guide, the Teletext (Televideo) functions are typically located on…
Why does my mount only beep and not move after a reset, even though the remote is paired?
Based on the manual for the VIVO MOUNT-E-FD70, if your mount is beeping but not moving after a reset, please check the following: Orientation:…
How do I program the M1 and M2 memory buttons on the MotoMotion SW419 remote control?
The provided manual for the MotoMotion SW419 identifies the M1 and M2 buttons but does not explicitly detail the programming sequence. However, for most…
How do I program the Pilotage Sanyo Universal Remote to work with a Technika TV?
Based on the provided manual for the Pilotage Sanyo Universal Remote Control, the brand Technika is not explicitly listed in the 3-digit code table.…
How do I turn off the light if the remote control is not working, and how do I reset the remote control?
If your remote control is not responding to turn off the light, you can use your wall switch to manage the lamp. The manual…
How can I fix or replace the baffle support bracket nuts that broke off while cleaning my Churchill 10 stove?
Since the nuts for the baffle support bracket have sheared off, you will likely need to replace the specific hardware or the internal support…
How do I program the Spectrum SR-002-R remote for an ONN TV?
If your ONN TV is not responding to the standard setup methods, you can try the Auto-Search mode to find the correct code: Turn…
How do I copy parameter data on the Yaskawa A1000 drive?
To copy parameters on the Yaskawa A1000 drive, you use the Copy Function built into the Digital Operator (JVOP-180). This allows you to upload…
My remote control only turns the fan light on and off, but no longer controls the fan speeds. I have already replaced the battery. What should I do?
It sounds like you're experiencing an issue where your EOGIFEE FAN-53T remote control is only operating the light function and not the fan speeds,…
The recording button on my universal remote is not working with my Qilive TV, model Q32H231B. It performs the function of another button on the original remote, but does not activate recording, and I can't find an alternative. Also, the codes provided for Qilive don't work; I had to use the first one for Grunkel TVs.
It sounds like you're experiencing two issues: the recording button on your Qilive Q.1538 universal remote isn't working as expected with your Qilive Q32H231B…
How do I perform the step-by-step calibration process for the LoraTap SC500W curtain switch using the Smart Life app?
To calibrate your LoraTap SC500W-V2 curtain switch in the Smart Life app, follow these steps: Open the Smart Life app and select your curtain…
How do I factory reset my Aubess smart switch and resolve connectivity issues when the light is blinking slowly?
To reset your Aubess smart switch to factory settings and resolve connectivity issues, you can use one of the following methods: Button Method: Long…
The red light is flashing and it won't start. Could it be that it's not getting diesel? It's new and I ran out of fuel, could it have taken in air?
A flashing red light on your Autoterm AIR-2D heater indicates a malfunction. The number of blinks corresponds to a specific error code. Based on…
What are the specifications and usage instructions for the Warrior 59386 Router Speed Control?
The Warrior 59386 Router Speed Control is designed to adjust the speed of routers with a current capacity of up to 8A and a…
How do I wire and configure two BFT EPB 24V drop bolts to a Rigel 6 control unit?
Based on the BFT Rigel 6 terminal layout and common connections, here is the guidance for wiring and setting up 24V accessories like drop…
How do I reprogram a Paradox REM25 remote control to an older system from 2017?
To program or reprogram a Paradox REM25 remote control to your security system, you generally need to access the programming mode of your main…
Why is my Roca 532083 Dynamic Wiper Control box making an intermittent clicking sound like a circuit breaker even when it is in the off position?
The intermittent clicking sound you are hearing from your Roca 532083 Dynamic Wiper Control box, even when in the "Off" position, likely indicates that…
Can the SSC-25 soft-starter remain permanently connected to the 230VAC mains and trigger a soft start when a load is introduced via a built-in float switch?
Based on the SSC-25 technical specifications and wiring diagrams, the unit is designed to be mains-operated and is suitable for pump applications. However, there…
How do I reset the replacement remote for my TV box?
To reset your Umiconty replacement remote, please follow these steps: Unplug your Fire TV device from the power source for at least 60 seconds.…
How do I delete or disable Xiaomi parental controls?
To disable or remove parental controls on your Xiaomi device, follow these steps: Disable for all apps: Go to Settings > Additional settings >…
How can I view the full-day schedule for a channel?
To view the schedule for a channel, press the Guide Button on your remote control. This will open the StreamTV guide. The manual indicates…
Why does the next button on my J06 remote control go to the previous page instead of the next page?
It sounds like your J06 remote is either in the wrong mode for your reading application or the AssistiveTouch settings on your device need…