How can I replace a lost bass remote for the Stinger MT-700.1 amplifier?
To replace the lost bass remote for your Stinger MT Series amplifier, you should look for the specific part number SA1RBC, which is the…
Manuals+ Q&A
Amplifiers questions & answers
Browse answered questions about Amplifiers, including setup, troubleshooting, compatibility and maintenance.
Browse topics
Answered questions
My amplifier makes a crackling sound when the temperature is above 30 degrees Celsius, even with the volume turned completely down. This issue disappears in cooler weather.
The Fender Champion 100 Owner's Manual does not specifically address crackling sounds related to high temperatures. However, it does provide general safety instructions that…
Why can't I hear my looper pedal through headphones when it is connected to the effects loop of the Fender Champion 100?
Based on the Fender Champion 100 manual, the PHONES jack (M) is designed to provide the amplifier effects in stereo and automatically mutes the…
What are the PRE OUT and PWR IN jacks used for on the Fender Champion 100?
On the Fender Champion 100, the PRE OUT and PWR IN jacks are used together to create an effects loop for external signal processing.…
How do I connect the Power Acoustik RZ4-2000DSPB amplifier to my car's power and ground?
To connect the Power Acoustik RZ4‐2000DSPB DSP Class D Full Range Amplifiers to your car's power and ground, follow these steps: 1. Disconnect the…
How do I connect the aune DAC-BT to my audio system?
To connect the aune DAC-BT to your audio system, please follow these steps: 1. Identify the audio outputs on your source device (e.g., computer,…
How long does it take to fully recharge the Emanya ZTQ-01 Noise Cancelling Hearing Amplifiers?
It takes approximately three hours to fully recharge the Emanya ZTQ-01 Noise Cancelling Hearing Amplifiers. When the hearing aids are fully charged, the charging…
How do I connect my speakers to the AMP-200BT amplifier?
To connect your speakers to the AMP-200BT amplifier, you can use the binding posts located on the amplifier. These binding posts accept bare wire,…
How do I connect the eHSA4-60 amplifier to high impedance and low impedance lines?
To connect the eHSA4-60 amplifier to high impedance lines, you need to connect the loudspeaker line to the amplifier's 0V and 70V terminals for…
How do I properly set up and connect the Icon Audio MB90 MK IIm Mono Block Amplifiers for optimal performance?
To properly set up and connect your Icon Audio MB90 MK IIm Mono Block Amplifiers, follow these steps based on the instruction manual: 1.…
How do I properly set the gain control on my KICKER CXA360.4 amplifier?
To properly set the gain control on your KICKER CXA360.4 amplifier, follow these steps: 1. **Basic Setup:** - Turn off the amplifier and disconnect…
How do I properly wire and connect Zapco ST-B Series amplifier ensure optimal performance avoid potential issues?
To properly wire and connect your Zapco ST-B Series amplifier, follow these steps based on the information provided in the owner's manual: 1. **Power…
How do I access and configure Monitor Audio IA60-4 Installation Amplifier using configuration web app via WiFi?
To access and configure the Monitor Audio IA60-4 Installation Amplifier using the configuration web app via WiFi, follow these steps: 1. **Power on the…
How to properly set up and operate my Crown CTs 4200 Multi-Channel Power Amplifier?
The Crown CTs 4200 Multi-Channel Power Amplifier is a versatile and powerful audio amplification device. Here are some key features and operational instructions based…
How do I connect my MAESTRO-812DSP-DSD Amplifier to my car audio system?
To connect your MAESTRO-812DSP-DSD Amplifier to your car audio system, follow these steps based on the provided manual: 1. **Prepare for Installation:** - Ensure…