PSI T019-05 TVL Sending Unit Installation Guide

Identify Mounting Location:
- Recommended placement for the sending unit includes the battery
  box, cross-brace behind the cab, or lower gusset for side
  deflector.
- Repeater must be installed to ensure proper system
  operation.
- Avoid mounting the sending unit where tires can throw debris
  onto the enclosure.
Mounting Procedure:
- Use the sending unit as a template to mark hole locations and
  drill with a 3/8 drill bit.
- Attach the sending unit using supplied bolts, washers, and
  locknuts. Torque bolts to 8-10 ft.-lbs.
- If mounting externally, use a strain relief cable tie with a
  drip loop configuration and ensure the connector faces
  downward.
Repeater Placement:
- Recommended placement near the first drive axle or optionally
  in the cab behind the center console.

Frequently Asked Questions (FAQ)

Q: What should I do if I encounter issues with system operation
after installation?

A: If you experience any problems with system operation
post-installation, check the power supply connections and ensure
all components are securely mounted following the provided
instructions. If issues persist, contact customer support for
further assistance.

“`

View Fullscreen

TPMS Sending Unit, Repeater and Harness Installation
Truck/Tractor Applications
INSTALLATION MANUAL
TireView® LIVETM Sending unit, Harness and Repeater Installation

Truck/Tractor Applications

www.psitireinflation.com/resources#tpms-resources

A Clarience Technologies Company.

V019 05 TVL Tractor Install Video

T019-03 Rev 08-25

TPMS Sending Unit, Repeater and Harness Installation
Truck/Tractor Applications
About this Manual This manual supplies installation procedures for the TireView® LIVETM sending unit. Use the procedures in this manual to install the system on commercial vehicles. Before You Begin
CAUTION: DO NOT PERFORM UNAUTHORIZED MAINTENANCE OR REPAIR PROCEDURES, OR INSTALL NON-P.S.I.® COMPONENTS ON ANY P.S.I. ® SYSTEM. THIS CAN VOID THE WARRANTY. 1. Read and understand all instructions and procedures before service to components begins. 2. Read and observe all Warning and Caution alert messages in this publication. They provide information that can prevent personal injury, damage to components, or both. 3. Follow the P.S.I. installation, maintenance, service, and troubleshooting guidelines. 4. Use special tools, when required, to avoid personal injury and damage to components. 5. Use personal protective equipment (PPE), when required, to avoid personal injury. Safety glasses, safety toe shoes, and gloves recommended.
Hazard Alert Messages and Torque Symbols
WARNING: A Warning alerts the technician to an instruction or procedure that must be followed to avoid personal injury and damage to components.
CAUTION:
A Caution alerts the technician to an instruction or procedure that must be followed to avoid damage to components.
TORQUE REQUIRED: The torque symbol alerts the technician to tighten fasteners to a specified torque value.
Additional Information Visit the Resource section at www.psitireinflation.com to access and request additional information. Call P.S.I.® at 210.222.1926 (United States and Canada) or email info@psitireinflation.com or techsupport@psitireinflation.com.
Introduction
The P.S.I.® TireView® Tire Pressure Monitoring System (TPMS) is designed to monitor air pressure and temperature in the tire. It is only for added safety and not meant to replace regular tire maintenance and exercise of reasonable care when operating a motor vehicle. The system cannot prevent accidents nor will P.S.I.® be responsible for damage or injury due to (a) improper use,(b) failure to follow the product manufacturer’s instructions or to perform preventative maintenance, (c) unauthorized repair or modifications, (d) use of products beyond their useful life, or (e) external causes such as accidents, abuse, or other actions or events outside of P.S.I.® control.

A Clarience Technologies Company.

T019-03 Rev 08-25

TPMS Sending Unit, Repeater and Harness Installation
Truck/Tractor Applications

Introduction
This manual is intended to provide guidance when installing the TireView® LIVETM sending unit and repeater on a commercial truck, tractor, or similar vehicle. Your configuration may vary due to type of equipment. Consult your support team for guidance.

Sending Unit, Harness and Repeater Components

PART DESCRIPTION

EXAMPLE

TireView LIVE Sending Unit

TireView Repeater

Wire Harness

Hardware Bag Cable Ties

Decals

A Clarience Technologies Company.

T019-03 Rev 08-25

TPMS Sending Unit, Repeater and Harness Installation
Truck/Tractor Applications
Installation Steps
1. Identify suitable mounting location for the TireView LIVE (TVL) sending unit and repeater. See Figure 1.

CAUTION: The repeater must be installed to help ensure proper operation of the TireView system. Failure to install the repeater could void warranty.
Sending unit
RECOMMENDED PLACEMENT: on battery box (ensure clearance behind fairing), cross-brace behind cab, or lower gusset for side deflector.
OPTIONAL PLACEMENT: on the back of the cab.
NOTE: Consult vehicle owner operator, fleet owner, or management before mounting sending unit to cab.

Sending Unit Repeater

CAUTION: Do not mount sending unit where tires can throw debris onto enclosure as this could cause damage.

CAUTION: Make sure location is suitable to route power wire harness to the sending unit.
2. Using the TVL sending unit as a template, mark mounting hole locations and drill with a 3/8″ drill bit. See Figure 2.
3. Use supplied bolts, washers, and locknuts to attach sending unit to vehicle.

Figure 1: Recommended sending unit and repeater locations.

TORQUE mounting bolts to 8-10 ft.-lbs.

CAUTION: If mounting to the cab, seal any penetrations into the body with Silicone RTV when attaching the sending unit. Screws and sealant are not included in the kit for this installation method. Technician is responsible to ensure no damage is done to equipment inside cab.
CAUTION: When mounting TVL sending unit EXTERNALLY, you must utilize a strain relief cable tie with drip loop configuration and ensure the Weather Pack connector is facing downward. See Figure 3.

Figure 2
Drip loop

Strain relief cable tie
Face connector downward

Figure 3
4

T019-03 Rev 08-25

TPMS Sending Unit, Repeater and Harness Installation
Truck/Tractor Applications

Repeater
RECOMMENDED PLACEMENT: near the first drive axle, central on the vehicle. See Figures 1 & 4.

OPTIONAL PLACEMENT: in cab, behind center
console, minimum 3 feet from the Sending Unit if possible. See Figures 1 & 5.

CAUTION: Avoid mounting the repeater where it is surrounded by metal (i.e., inside a cross member). This can prevent sensor signals from reaching the sending unit and will cause loss of data.
4. Mount the repeater using cable ties (included), bolts, or rivets. Repeater harness should be secured to factory wire harness or air lines with supplied cable ties and route towards the battery box. See Figures 4 & 5.
Wire Harness Connection
5. Starting at the component furthest from the fuse panel (usually the repeater) connect one lead of the wire harness to the Weather Pack connector on the component harness. Secure harness to factory wire harness or air lines with supplied cable ties and route towards the fuse panel.

Figure 4 Figure 5: Optional repeater location.

WEATHER PACK CONNECTORS

NOTE: The supplied wire harness has 2 preterminated Weather Pack connectors. One lead is longer than the other, but the connectors are electrically the same. Use the proper length lead for each component. See Figure 6.
6. Connect the second lead of the wire harness to the Weather Pack connector on the remaining component (usually the TVL sending unit). Secure harness to factory wire harness or air lines with supplied cable ties and route towards the battery box.
Battery Box Connection Example
7. Connect ring terminals of the harness to the battery terminals, ensuring positive (+) and negative (-) leads are on correct terminals. Secure any excess harness using supplied cable ties. Ensure wire harness does not interfere with installation of battery cover, if applicable. Verify 2A fuse is installed in wiring harness fuse holder. See Figure 7.

Figure 6
Negative (-) ring terminal
Fuse holder (2A)
Positive (+) ring terminal

Figure 7
5

T019-03 Rev 08-25

TPMS Sending Unit, Repeater and Harness Installation
Truck/Tractor Applications

Power on System
8. When power is applied, verify status lights on TVL sending unit. See Figure 8.

TireView LIVE Receiver indicator light

LED Signal ACQUIRED

(Signal)

(Blinking)

NO LIGHT

RED

Check power connection

TireView LIVE Sending Module indicator lights

LED

SEARCHING for Signal ACQUIRED

(Signal) Signal (Blinking)

(Solid)

GREEN (GPS)

AMBER (Cellular)

NOTE: If green or amber lights do not turn solid, move vehicle outdoors or to an area with better cellular coverage.
Install Decals
9. Consult vehicle owner operator, fleet owner, or management for decal placement. Clean surface prior to decal installation.

NOTE: Do not place decals on sending unit cover or obstruct sending unit barcode label.
Program Sensors to System
10. Use the mobile app (Goodyear® TPMS PlusTM, TireView LIVE, etc.) to program the system and install sensors.

Figure 8

A Clarience Technologies Company.

T019-03 Rev 08-25

TPMS Sending Unit, Repeater and Harness Installation
Truck/Tractor Applications

Record of Revisions

Revision Number

Revision Date

October 23, 2024

August 20, 2025

A Clarience Technologies Company.

T019-03 Rev 08-25

Pressure Systems International 4323 Interstate Way, San Antonio, TX 78219 USA Phone: 210.222.1926, Fax: 210.568.4221 www.psitireinflation.com

Visit www.psitireinflation.com/resources or scan this QR code for access to the latest revision of this manual.

A Clarience Technologies Company.

T019-03 Rev 08-25

Documents / Resources

PSI T019-05 TVL Sending Unit [pdf] Installation Guide
T019-05, T019-05_Rev_08-25_TPMS_INSTALL-TRUCK-Rev2, T019-05 TVL Sending Unit, T019-05, TVL Sending Unit, Sending Unit, Unit

References

User Manual

PSI T019-05 TVL Sending Unit Installation Guide

T019-05 TVL Sending Unit

Product Specifications

Product Usage Instructions

Introduction

Sending Unit, Harness, and Repeater Components

Installation Steps

Frequently Asked Questions (FAQ)

Q: What should I do if I encounter issues with system operation
after installation?

Documents / Resources

References

Leave a comment

Cancel reply