PROLED L711UDA3 Sensor Remote
Product Specifications
- Product Name: PROLED SENSOR REMOTE – L711UDA3
- Manufacturer: MBN GmbH
- Address: Balthasar-Schaller-Str. 3, 86316 Friedberg, Germany
- Website: www.proled.com
Product Usage Instructions
Key Functions
- ON / OFF: Switch ON / OFF the light. Switch OFF sensor function.
- MW / PIR: Mode switch.
- RESET: Switch to sensor mode and recover all settings to factory default.
- START MEMORY APPLY: Follow the steps to set and apply memory settings.
- DETECTION AREA: Adjust the detection area.
- HOLD TIME: Set the hold time.
- DAYLIGHT THRESHOLD: Configure the daylight threshold.
- STAND-BY PERIOD: Set the stand-by period.
- STAND-BY DIMMING LEVEL: Adjust the stand-by dimming level.
- UP DOWN: Use these keys to adjust parameter values.
- POWER: Set the brightness level.
- TEST MODE: Activate the test mode.
Setting Parameters
To set parameters, follow the instructions provided in the manual for each key function. Make sure to confirm settings by pressing the appropriate buttons as required.
Power Output Setting
The power output can not be set below 60%, even if the display shows 10%.
Frequently Asked Questions (FAQ)
- Q: How do I reset the remote control?
A: Press “RESET” to switch to sensor mode and recover all settings to factory default. - Q: How do I adjust the brightness level?
A: Under sensor mode, press the “POWER” key. The icon will flash, and you can adjust the brightness using the up (+) or down (-) buttons.
PROLED SENSOR REMOTE – L711UDA3
|
|
Remote keys | Key function | Key description |
 |
ON / OFF | Switch ON / OFF the light. Switch OFF sensor function | |
 |
MW / PIR | Mode switch | |
 |
RESET | Switch to sensor mode and recover all settings to be factory default (Detection area 100%, Hold time 5 s, Daylight disabled, Stand-by period 0 s, Stand-by dimming 10%) | |
 |
START | 1. Press „START“. Bottom left „S“ start blinking. Start setting all parameters.
2. Press „MEMORY“ to store the setting untill next reset. 3. Press „Apply“ to set sensors with stored settings within FR-range. 4. All data shown in the display are the settings after pressing “Memory” |
|
 |
MEMORY | ||
 |
APPLY | ||
 |
DETECTION AREA | Under sensor mode, press a key. The corresponding icon on the display flashes. Press + / – to select the sensitivity. | |
 |
HOLD TIME | Under sensor mode press the key. Corresponding icon will flash and with + / – you can set the hold time. 5 s / 30 s / 1 min / 3 min / 5 min / 10 min / 20 min / 30 min | |
 |
DAYLIGHT TRESHOLD | Under sensor mode press the key. Corresponding icon will flash and with + / – you can set the daylight threshold. | |
 |
STAND-BY PERIOD | Under sensor mode press the key. Corresponding icon will flash and with + / – you can set the Stand-by period. 0 s / 10 s / 30 s / 1 min / 5 min / 10 min / 30 min / 60 min | |
 |
STAND-BY DIMMING LEVEL | Under sensor mode press the key. Corresponding icon will flash and with + / – you can set the stand-by dimming value. | |
 |
UP |
After pressing different parameter key, press either up (+) or down (-) to adjust desired value. |
|
 |
DOWN | ||
 |
POWER | Under sensor mode press the key. Icon „PW“ will flash and with + / – you can set the brightness. | |
 |
TEST MODE | Press the key to activate the test mode. It won’t be memorized after power off. Following parameters will be activated:
Detection area 100%, hold time 2s, Daylight disabled, Stand-by 0s, Stand-by dimming 10% |
|
| Notice | Press „Scene“ to reset the remote before using. During setting of each parameter, the icon will flash for 5 s. After that the settings will be kept automatically. | ||
Microwave-sensor settings – one sensor
- Press ON / OFF button to turn on the light.
- Press „Scene“-button to reset remote control and swith to sensor mode.
- Press related keys to set, within of 5 s after the corresponding icon starts blinking, the detection area, hold time, daylight threshold, stand-by period und stand-by dimming value with + / – keys.
- Than all settings would be kept automatically until next reset.
Start / Memory / Apply – allied to more sensors
- Press ON / OFF button to turn on the light.
- Press „Scene“-button to enter sensor mode. Press „Start“ to begin user-defined setting.
- Press related keys to set, within of 5 s after the corresponding icon starts blinking, the detection area, hold time, daylight threshold, stand-by period und stand-by dimming value with + / – keys.
- Press „Memory“ button to store the settings.
- Press „Apply“ button to program all sensors in range. The light will blink rapidly when receiving the signal, which means the sensor has been successfully programmed.
Power output setting
- The output could be set under two mode – sensor mode and always ON mode.
- Under always-ON-mode, press + / – buttons to adjust the output from 10-100%.
- Under sensor-mode, press „Scene“ – „Power“ – than press + / – buttons to adjust the output from 60-100%. The output can not be set below 60%, even if the display shows 10%.
09.24 Technical amendments reserved
MBN GmbH, Balthasar-Schaller-Str. 3, 86316 Friedberg – Germany www.proled.com
Documents / Resources
 |
PROLED L711UDA3 Sensor Remote [pdf] Installation Guide L711UDA3 Sensor Remote, L711UDA3, Sensor Remote, Remote |
 |
PROLED L711UDA3 Sensor Remote [pdf] Instruction Manual L711UDA3, L711UDA2, L711UDA3 Sensor Remote, L711UDA3, Sensor Remote, Remote |
