PROLED Sensor Remote L711UDA3

Installation Manual

Remote Overview

The PROLED Sensor Remote L711UDA3 is designed to control and configure PROLED sensor devices. It features a display that shows current settings and allows for adjustments via dedicated buttons.

The remote control includes a display screen showing parameters such as detection area, hold time, daylight threshold, standby period, and standby dimming level. It is operated using various buttons including ON/OFF, MW/PIR, RESET, START, MEMORY, APPLY, UP, DOWN, POWER, and TEST MODE.

Remote Keys	Key Function	Key Description
ON / OFF		Switch ON / OFF the light. Switch OFF sensor function.
MW / PIR	Mode switch	Switches between microwave and PIR sensor modes.
RESET		Switch to sensor mode and recover all settings to be factory default (Detection area 100%, Hold time 5 s, Daylight disabled, Stand-by period 0 s, Stand-by dimming 10%).
START		1. Press START. The "S" indicator at the bottom left will start blinking. Begin setting parameters. 2. Press MEMORY to store the setting until the next reset. 3. Press Apply to set sensors with stored settings within FR-range. 4. All data shown in the display are the settings after pressing "Memory".
DETECTION AREA		Under sensor mode, press the key. The corresponding icon on the display flashes. Press [Up] / [Down] to select the sensitivity (detection area).
HOLD TIME		Under sensor mode, press the key. The corresponding icon will flash and with [Up] / [Down] you can set the hold time. Options include: 5s, 30s, 1 min, 3 min, 5 min, 10 min, 20 min, 30 min.
DAYLIGHT THRESHOLD		Under sensor mode, press the key. The corresponding icon will flash and with [Up] / [Down] you can set the daylight threshold.
STAND-BY PERIOD		Under sensor mode, press the key. The corresponding icon will flash and with [Up] / [Down] you can set the Stand-by period. Options include: 0 s, 10 s, 30 s, 1 min, 5 min, 10 min, 30 min, 60 min.
STAND-BY DIMMING LEVEL		Under sensor mode, press the key. The corresponding icon will flash and with [Up] / [Down] you can set the stand-by dimming value.
UP / DOWN		After pressing a parameter key, press either [Up] or [Down] to adjust the desired value.
POWER		Under sensor mode, press the key. The "PW" (Power/Brightness) icon will flash and with [Up] / [Down] you can set the brightness.
TEST MODE		Press the key to activate the test mode. Settings will not be memorized after power off. Following parameters will be activated: Detection area 100%, hold time 2s, Daylight disabled, Stand-by 0s, Stand-by dimming 10%.
Notice		Press "Scene" to reset the remote before use. During setting of each parameter, the icon will flash for 5 seconds. After that, the settings will be kept automatically.

Operating Instructions

1. Microwave-Sensor Settings – One Sensor

Press the ON / OFF button to turn on the light.
Press the "Scene" button to reset the remote control and switch to sensor mode.
Press the relevant keys to set the detection area, hold time, daylight threshold, stand-by period, and stand-by dimming value using the [Up] / [Down] buttons. This should be done within 5 seconds after the corresponding icon starts blinking.
All settings will be kept automatically until the next reset.

2. Start / Memory / Apply – For Multiple Sensors

Press the ON / OFF button to turn on the light.
Press the "Scene" button to enter sensor mode. Press "Start" to begin user-defined setting.
Press the relevant keys to set the detection area, hold time, daylight threshold, stand-by period, and stand-by dimming value using the [Up] / [Down] buttons. This should be done within 5 seconds after the corresponding icon starts blinking.
Press the "Memory" button to store the settings.
Press the "Apply" button to program all sensors within range. The light will blink rapidly when receiving the signal, indicating the sensor has been successfully programmed.

3. Power Output Setting

The output can be set under two modes: sensor mode and always ON mode.

Under always-ON mode, press the [Up] / [Down] buttons to adjust the output from 10-100%.
Under sensor mode, press the "Scene" then "Power" buttons, then press the [Up] / [Down] buttons to adjust the output from 60-100%. The output cannot be set below 60%, even if the display shows 10%.

4. Test Mode Activation

Press the TEST MODE button to activate the test mode. Settings configured in test mode are not memorized after power off. The following parameters are activated in test mode: Detection area 100%, hold time 2s, Daylight disabled, Stand-by 0s, Stand-by dimming 10%.