POWERTECH ZM9126 Canvas Blanket Solar Panel with Charge Controller
INTRODUCTION:
Please ensure that you have read the product manual and instructions in full before using this product. Failure to do so many result in incorrect operation and potentially impact the performance of the product. This product converts natural sunlight into DC electricity. It is designed to charge a 12V battery.
BOX CONTENTS:
- 1 x 400W Canvas Blanket Solar Panel
- 1 x 30A Solar Regulator
- 2 x Leads
CAUTION/WARNING:
- For optimum performance, protect the solar cell from dust, dirt, and other debris.
- Use and store the product in a dry and ventilated location.
- Do not use in flammable or explosive areas.
- Stop use immediately if any wires become loose or electronic components are exposed.
- Do not pick panel up directly by the solar cells.
- Use the gap between solar cells to pick up the panel.
- Do not stand or walk on the solar panel.
PRODUCT SPECIFICATIONS:
| Solar Panel | |
| Solar Cell Type: | Monocrystaline |
| Power Output: | 400W |
| Open Circuit Voltage: | 23.7V |
| Short Circuit Current: | 18A |
| Working Voltage: | 22.6V |
| Working Current: | 17.6A |
| Output: | Anderson, USB2.0, USB/QC3.0, Type-C/ PD60W, DC5521 |
| Weight: | 10.5KG |
| Dimensions: | |
| Folded: | 572(W) x 360(H)mm |
| Unfolded: | 1142(W) x 1898(H)mm |
| Solar Charge Controller | |
| System Voltage: | 12V |
| Charge Current: | 30A |
| Discharge Current: | 30A |
| Max. Solar Current: | <50V |
| Battery Equalisation: | |
| Sealed: | 14.4V |
| GEL: | 14.2V |
| Flood: | 14.6V |
| Float Charge: | 13.7V (Default, Adjustable) |
| Discharge Stop: | 10.7V (Default, Adjustable) |
| Discharge Reconnect: | 12.6V (Default, Adjustable) |
| USB Output: | 5V, 2A |
| Self-Consumption: | <10mA |
| Operating Temperature: | -35°C ~ 60°C |
| Weight: | 200g |
HOW TO USE:
- Unfold the solar panel.
- Place the unfolded solar panel in a position that receives direct sunlight, facing to the sun. Ensure that no shadows are covering the solar cells.
- Tilt the solar panel at a suitable angle. This can be the same as your local latitude (additional support may be necessary, not supplied).
- Connect the solar panel to the solar charge controller before connecting battery clamp lead to the solar controller.
HOW TO CHARGE A 12V BATTERY :
- Connect the battery to the solar charge controller.
- Connect load to solar charge controller.
- Connect solar panel to solar charge controller.
- Reverse this order when disconnecting.
Note: Heavy loads should not be connected to the battery.
LCD DISPLAY/KEY:
DISPLAY/SETTINGS:
TROUBLESHOOTING:
| Error Code | Cause | Solution |
|
E01 |
Low battery voltage, load off | Change the battery or change a new battery. |
|
E02 |
Overload, load off |
Decrease the load, the use (-) button to turn on the load.
Load will automatically turn on after 2 minutes. |
|
E03 |
Load short-circuit, load off |
Remove the short-circuit load, use (-) button to turn on the load. |
|
E04 |
Over-voltage of battery, load off |
Check the connection of battery, and whether if the capacity of battery is too low, check if there is another charger connected to the battery. |
|
E05 |
Solar panel over current, controller stops charging |
Check whether the power of solar panel has been over powered, decrease the panels and then
the controller will start charging automatically after 2 minutes. |
FULL TECHNICAL PARAMETERS:
|
Solar Input |
Rated Current | 30A |
| Input Voltage | ≤50V
(12V) |
| Charge Management | ||||||||
|
Lead-acid Batteries |
3-stage charging (bulk charge, absorption charge, float charge) | |||||||
| Lead-acid Batteries |
Sealed |
GEL |
Flood |
USE1 |
||||
| Float Voltage | 13.8V | 13.8V | 13.8V | 13.8V (9~15V adjustable) | ||||
| Absorption Voltage |
14.4V |
14.0V |
14.6V |
14.4V (9~15V adjustable) |
||||
| Absorption Time | 2 hours | |||||||
| Absorption Recovery Voltage |
12.6V |
|||||||
| Limited Charge Voltage |
15.5V |
|||||||
| Temperature Compensation |
-4mV/cell/°C |
|||||||
|
Lithium Batteries |
3-stage charging (bulk charge, constant-voltage, stop charge) | |||||||
| Lithium Batteries | 3.7-3 | 3.7-4 | 3.2-4 | 3.2-5 | USE2 | |||
|
Constant Voltage |
12.6V |
16.8V |
14.4V |
18.0V |
14.4V
(9~17V adjustable) |
|||
| Cut-off Charge Current |
2A (0.1A~30A adjustable) |
|||||||
| Recovery Charge Voltage |
12.0V |
16.0V |
13.6V |
17.0V |
13.6V
(9~17V adjustable) |
|||
Note: Parameters apply to 12V system as an example. If 24V/36V/48V system, the voltage parameters should be *2/*3/*4
Note: 10A/20A controller without temperature compensation/backlight function, without cut-off current.
| B01 | B02 | B03 | B04 | B00 |
|
Sealed battery |
Gel Battery |
Flood Battery |
Lithium Battery – Custom Type | Lead-acid Battery – Custom Type |
FULL TECHNICAL PARAMETERS:
| Discharge Management | |||||||||
|
Batteries Type |
Lead-acid Batteries | Lithium Battery | |||||||
| 3.7-3 | 3.7-4 | 3.2-4 | 3.2-5 | USE1 | |||||
| Low-Voltage Protection | 10.7V
(9~15V adjustable) |
9.9V |
13.2V |
11.2V |
14.0V |
11.2V
(9~17V adjustable) |
|||
| Low-Voltage Recovery | 12.6V
(9~15V adjustable) |
11.1V |
14.8V |
12.8V |
16.0V |
12.8V
(9~17V adjustable) |
|||
| Over-Voltage Protection |
16.0V |
18.5V |
|||||||
| Over-Voltage Recovery |
15.5V |
18.0V |
|||||||
| USB Power | 5V USB, Max output 2A | ||||||||
| Voltage Range of Battery | |||||||||
|
System Voltage |
Lead-acid Batteries | Lithium Battery | |||||||
| 3.7-3 | 3.7-4 | 3.2-4 | 3.2-5 | USE2 | |||||
| 12V | ≤17V | ≤14.6V | ≤18.8V | ≤16.4V | ≤20V | ≤16.4V | |||
| Other Specifications | |
| Max Wire Size | 6mm2 (AWG #9) / 16mm2 (AWG#5) / 25mm2 (AWG #3) |
| Working Temperature | -20°C ~ 50°C |
| Storage Temperature | -30°C ~ 70°C |
| Working Humidity | 10% ~ 90%, no condensation |
| Dimensions | 187 x 98 x 50mm |
| Weight | 370g |
| Waterproof | IP30 |
FACTORY DEFAULT SETTINGS:
At main loop interface 2 , press & hold the MENU button until the symbols in the dotted column starts flashing, the controlling parameters will reset to the default value. Controller will restart automatically to re-new the controller data.
VARIOUS WORKING MODES FOR LOAD:
There are four control modes for the load. (1) Normal control mode, (2) Light control on, (3) Delayed off mode, (4) Reverse light control mode. The delayed duration can be between 1-24 hours.Following are the working introduction for each mode:
|
Load Mode |
Event | ||
| Dark | Setting Time | Dawn | |
| 24H normal control mode | – | – | – |
| 1-23H light control on and delayed off mode |
Load on |
Load off |
Load off |
| 0H light control mode | Load on | – | Load off |
| CH reverse light control mode | Load off | – | Load on |
Distributed by:
Electus Distribution Pty. Ltd. 320 Victoria Rd, Rydalmere NSW 2116 Australia
www.electusdistribution.com.au
Made in China
Documents / Resources
 |
POWERTECH ZM9126 Canvas Blanket Solar Panel with Charge Controller [pdf] Instruction Manual ZM9126, Canvas Blanket Solar Panel with Charge Controller |
