POSIFLEX MT-6210A Mobile Terminal System
Package Contents
- MT-6210A (x 1)
- 45W power adaptor (x 1)
- Protection case, hand strap, shoulder strap and stylus for option (x 1)
MT-6210A is required to be charged over 8 hours when used for the first time.
FCC NOTES
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance.
CE CLASS A WARNING
This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may cause radio interference.
WARRANTY LIMITS
Warranty will terminate automatically when the machine is opened by any person other than the authorized technicians. The user should consult his/her dealer for the problem happening.
Warranty voids if the user does not follow the instructions in the application of this merchandise. The manufacturer is by no means responsible for any damage or hazard caused by improper application.
SAFETY INSTRUCTIONS
This equipment is not suitable for use in locations where children are likely to be present.
WARNING Power cord shall be connected to a socket-outlet with earthing connection.
BATTERY WARNING
Risk of explosion if battery is replaced by an incorrect type. Dispose of expended battery in accordance with local disposal regulations.
Views of MT-6210A
Charging the Battery
Below are some cautionary advices you need to keep in mind while you attempt to charge the battery.
- MT6210A is required to be charged over 8 hours when used for the first time.
- When the low battery warning message appears, please fully charge the battery to avoid data loss.
- When the low battery capacity indicator beams or low battery warning message appears, please charge the battery immediately.
- Only charge the battery with power adapter which comes with MT-6210A. Using a different power adapter may damage your device.
- When the battery is running very low (less than 6 percent of battery capacity), the system will be automatically shut down to protect the battery from being over-discharged.
Please go through the following instructions to charge MT-6210A using the power adapter.
- Find the type-C connector on the bottom side of your tablet, and then connect the type-C power adaptor to it.
- Plug the AC power adaptor into an electrical outlet to initiate the charging process.
Status LED Indicator
LED indicator is specially designed to deliver special message regarding the current system status and battery life. The blow chart enumerates all the possible LED indicators and its meaning for your reference.
| LED Status | System Status | Descriptions |
| Solid Blue | ON | System booting. |
| Solid Red | ON | System is being charged. |
| Blinking Green | ON | Barcode scanner good read. |
| Blinking Red | ON | Battery charging error occurs. |
| OFF | ON | System enters sleep mode.
Battery is fully charged. |
| OFF | OFF | System powers off |
Powering ON/OFF
Shipping Mode
MT-6210A tablet will be set to shipping mode when shipped. When customers receive the product for the first time, they need to use the Type-C power adapter which provided in the packing to turn on the tablet. After the first boot is completed, the power button can be used to turn on the power.
Power ON MT-6210A
To power on MT-6210A, keep pressing the power button of the machine for 1-3 seconds. If the tablet falls into the sleep mode after remaining idle for a specific period of time, push the power button to wake the device up.
Power OFF MT-6210A
When MT-6210A stays in idle mode, push the power button to put your device into sleep mode, and press the power button again to wake up the tablet. To completely shut down the machine, you need to press and hold the power button for at least 10 seconds. In the case the system halts for unknown reasons, you are advised to hold down the button until a system shutdown is initiated.
Operating the Barcode Scanner (Optional)
MT-6210A model is equipped with an optional barcode scanner on the top side of the tablet. For more detailed information, please refer to the barcode scanner user manual. Scan the below barcode to restore Manual Trigger defaults.
To do the further setting of the scanner engine, please find the relevant user manual on Posiflex Global Website, (https://download.posiflex.com/en-global/Download/index/manualUinstall_guide/mobile-pos/MT-6210A) or contact the service team for technical support.
Operating the Hand Strap (Optional)
You can use the hand strap like the picture below.
Operating the Shoulder Strap (Optional)
Please follow below instructions to use the optional shoulder strap.
- Install the protection case onto the tablet.
- Hook the shoulder strap.
- Installation completed.
Installing Optional Upgrade Kits
MT-6210A can work with multiple optional upgrade kits, such as MSR, Smart Card Reader and the like. For the detailed instructions, please refer to the user manual related to each peripheral devices.
Specifications
| MT-6210A | |
| System | |
| CPU | MT8786 |
| Memory | LP4x 4GB (default) / 8GB |
| Front Camera | 2M pixels, FF, front facing camera |
| Rear Camera | 5M pixels, AF, rear facing camera |
| Sensors | G sensor, ambient light sensor |
| Battery | 7.70V/5930mAh |
| Operation Time | At least 8H |
| NFC | NFC as default, antenna on rear cover |
| Storage | |
| Storage | 64GB (default) / 128GB |
| OS Support | |
| OS Support | Android 13 with GMS (MADA) |
| Display & Monitor | |
| Display | 10.1” TFT LCD with LED backlight, 1280 x 800 |
| Touch Screen | P-CAP touch with multi-touch support |
| Expansion | |
| Wireless connectivity | WiFi IEEE 802.11a/b/g/n/ac (dual band 2.4GHz / 5GHz) + BT 5.0 |
| Power | |
| Power Supply | Power adapter: 45W (Type-C connector) Type-C input power 15VDC/3A |
| Outside I/O Ports | |
| Audio | 1 x built-in speaker + 1 x mic-in/line-out combo port |
| Docking Port | 1 x type-C as docking connector & power charging function |
| Power Switch Button | Yes |
| LED Indicator | Blue/green/red color LED x 1 |
| Mechanical | |
| Dimension | 261 (L) x 176.8 (W) x 19.4 (D) in mm |
| Weight | 888g |
| Optional Item | |
| 2D barcode scanner | 2D barcode scanner as option |
| Attachment | |
| TA-620 | Side attachment with fingerprint sensor |
Outline Dimension
The product information and specifications are subject to change without prior notice.
Documents / Resources
 |
POSIFLEX MT-6210A Mobile Terminal System [pdf] User Manual MT6200AW, V93MT6200AW, MT-6210A Mobile Terminal System, MT-6210A, Mobile Terminal System, Terminal System, System |