Polaris logo Polaris R0997900 Suction Cleaner Factory Tune Up KitInstallation Manual

Polaris Suction Cleaner Tune-Up Kit

These instructions are to be used with the following Polaris Tune-up Kit: R0997900
Warning WARNING
WARNING – This product must be serviced by a qualified professional with sufficient experience in pool equipment installation and maintenance so that all of the instructions in the product’s complete installation and operations manual can be followed exactly. All safety instructions in the complete manual must be followed explicitly in order to prevent injury hazards. Improper installation and/or operation may void the warranty.

Tool Required Polaris R0997900 Suction Cleaner Factory Tune Up Kit - icon

Disassembly

Polaris R0997900 Suction Cleaner Factory Tune Up Kit - Disassembly 1

  1. Press the release and open the lid.Polaris R0997900 Suction Cleaner Factory Tune Up Kit - Disassembly 2
  2. Pull the engine straight up to remove.Polaris R0997900 Suction Cleaner Factory Tune Up Kit - Disassembly 3
  3. Remove 8 screws and the gear covers.Polaris R0997900 Suction Cleaner Factory Tune Up Kit - Disassembly 4
  4. Lift drive shafts straight up to remove.Polaris R0997900 Suction Cleaner Factory Tune Up Kit - Disassembly 5
  5. Stretch tracks over the wheels to remove.Polaris R0997900 Suction Cleaner Factory Tune Up Kit - Disassembly 6
  6. Remove the screw between the wheels to remove the panel on each side.Polaris R0997900 Suction Cleaner Factory Tune Up Kit - Disassembly 7
  7. Remove the screw from the directional controller to remove it from the panel on each side.

Reassembly

  1. Polaris R0997900 Suction Cleaner Factory Tune Up Kit - Reassembly 1 Attach directional controller “A” to side panel “A” and controller “B” to side panel “B” with 1 screw each.Polaris R0997900 Suction Cleaner Factory Tune Up Kit - Reassembly 2
  2. Attach the panel on each side with 1 screw between the wheels.Polaris R0997900 Suction Cleaner Factory Tune Up Kit - Reassembly 3
  3. Guide the track on to the pulley, stretching it over the wheels and under the track guard, on each side.Polaris R0997900 Suction Cleaner Factory Tune Up Kit - Reassembly 4
  4. Replace drive shafts by aligning with turbine and direction controller gears.Polaris R0997900 Suction Cleaner Factory Tune Up Kit - Reassembly 5
  5. Ensure drive shaft gear teeth mesh with turbine and direction controller gears. Polaris R0997900 Suction Cleaner Factory Tune Up Kit - Reassembly 6
  6. Attach gear cover “A” to side “A” and cover “B” to s“B.” Replace 8 screws.Polaris R0997900 Suction Cleaner Factory Tune Up Kit - Reassembly 7
  7. Replace the engine. Lower straight down.Polaris R0997900 Suction Cleaner Factory Tune Up Kit - Reassembly 8
  8. Align engine guard with gear cover “A.” Ensure bearings are fully seated and the gear teeth mesh.Polaris R0997900 Suction Cleaner Factory Tune Up Kit - Reassembly 9
  9. Close the lid.

Polaris logoZodiac Pool Systems LLC
2882 Whiptail Loop # 100, Carlsbad, CA 92010
PolarisPool.com
Zodiac Pool Systems Canada, Inc.
2-3365 Mainway, Burlington, ON L7M 1A6
PolarisPool.ca
Zodiac Pool Care Europe
ZA de la Balme – BP 42, 31450 Belberaud, France
PolarisPool.eu
Fluidra Group Australia Pty Ltd
1 Herbert Place, Smithfield NSW 2164
PO Box 7238 Wetherill Park NSW 1851, Australia
PolarisPool.com.au
A Fluidra Brand
©2023 Zodiac Pool Systems LLC. All rights reserved. ZODIAC®
is a registered trademark of Zodiac International, S.A.S.U., used under license.
All other trademarks are the property of their respective owners.
H0814000_REVB

Documents / Resources

Polaris R0997900 Suction Cleaner Factory Tune Up Kit [pdf] Instruction Manual
R0997900 Suction Cleaner Factory Tune Up Kit, R0997900, Suction Cleaner Factory Tune Up Kit, Cleaner Factory Tune Up Kit, Factory Tune Up Kit, Tune Up Kit

References

Leave a comment

Your email address will not be published. Required fields are marked *