Contents
hide
PNI DK101 Control Access Keypad with Proximity Caed Reader
PRODUCT DESCRIPTION
TECHNICAL SPECIFICATIONS
Power voltage | 12Vdc+12% / 1.2A |
Unlock relay | 12Vdc/2A |
Work ambient temperature | -10 ~ 45°C |
Storage ambient temperature | -10 ~ 55°C |
Work relative humidity | 40~90% RH |
Storage relative humidity | 20~90% RH |
Card memory | 1000 pcs. |
PIN memory | 1*public , 1000*private |
Reader frequency | 125KHz |
Compatible card type | EM (electromagnetic) |
Card reading distance | 0 – 5 cm |
Electric lock interface | NO or NC relay output |
Available connections | Exit button / Bell / Door contact / Alarm |
FACTORY DEFAULT VALUES
Programming PIN | 881122 (please change this when first installing the keypad) |
Door open mode | Card or PIN (default public PIN 1234) |
Private PIN | 0000 |
Unlock time | 3 sec. |
Tamper alarm | On |
Door contact | Off |
Lock status | Off |
Alarm delay | 0 sec. |
Modify private PIN | Off |
OPTIC AND SOUND INDICATORS
Normal working mode:
- command confirmation: short beep
- invalid command: long beep
Programming mode
- green LED on
- command confirmation: 2 short beeps
- invalid command: 3 short beeps
FUNCTIONS AND SETTINGS PROGRAMMING
- Enter programming mode: press [#] + [programming PIN] (the default programming PIN is 881122). You will hear 2 confirmation beeps and the green LED will light.
- Change programming PIN: press [0] + [new programming PIN] + [confirm new PIN]. You will hear 3 confirmation beeps.
- Door open mode selection
- card or PIN: press [1] + [0]. You will hear 2 confirmation beeps.
- card + PIN: press [1] + [1]. You will hear 2 confirmation beeps.
NOTE: In card or PNI door open mode the PIN is either the public one or a private one (up to 999). - Door open time setting: press [2] + [TT], TT = time interval in seconds. You will hear 2 confirmation beeps.
For example, if the door open time is 3 sec then TT = 03 - Change public PIN: press [3] + [new 4 digit PIN]. You will hear 2 confirmation beeps.
- Tamper switch:
- disable: press [4] + [0]. You will hear 2 confirmation beeps.
- enable: press [4] + [1]. You will hear 2 confirmation beeps.
- Enrolling EM cards: press [5] + [3 digit index code] + present card 1 + present card 2 ……… + [3].
After every presented card you will hear 3 confirmation beeps. - the 3 digit index code (001 – 999) is important for deleting a lost card.
- when enrolling multiple cards the index code will be increased automatically.
- the default private PIN for every card is 0000
- Door contact:
- disable: press [6] + [0]. You will hear 2 confirmation beeps.
- enable: press [6] + [1] to deactivate the tamper switch. You will hear 2 confirmation beeps
- NOTE: The door contact must be purchased separately.
- Delete cards:
- Delete card by index code: press [7] + [index code 1] + [index code 2] + ..+ [#]. After every index code you will hear a long confirmation beep.
- Delete card by presenting it: press [7] + present card 1 + present card 2 + … + [#]. After every card you will hear a long confirmation beep.
- Delete all cards: restore factory default settings
- NOTE: The private PIN associated to a card will be deleted at the same time with the card.
- Modify private PINs:
- disable: press [1] + [2]
- enable: press [1] + [3] NOTE: Modify private PIN: exit programming mode the long press [#] (the green LED will light) + present card + [old private PIN] (default 0000) + [new private PIN] + [repeat new private PIN]. You will hear 2 confirmation beeps.
- Door contact alarm:
- disable: press [8] + [0]. You will hear 2 confirmation beeps.
- enable: press [8] + [1]. You will hear 2 confirmation beeps.
NOTE: Enabling this option will cause the keypad to sound when the door is left open or when the door is not unlocked from the keypad. - Alarm delay time: press [8] + [2] + [TT], TT = time interval in seconds. You will hear 2 confirmation beeps.
For example, if the door open time is 3 sec then TT = 03.
NOTE: This function can be used after enabling the door contact. - Exit programming mode: press [#]. You will hear 3 confirmation beeps.
- Cancel command: press [#]
- Restore factory default: press [8] + [6]
- Reset programming PIN: short the J2 jumper to reset programming PIN to factory default.
USER INSTRUCTION
Card or PIN door open mode:
- present card or type your private PIN on the keypad
Card + PIN door open mode:
- present card the type your private PIN on the keypad
FREQUENTLY ASKED QUESTIONS
After the lock is opened there are 8 short beeps | – the keypad needs higher voltage, please check
the power supply |
The card reading distance is to short or the card
can’t be read |
– the electric current is to low, please check the power supply |
After presenting the card there are 3 beeps and the
lock doesn’t open |
– the keypad works only in card+PIN mode
– the keypad is in programming mode |
Present an enrolled card does not unlock the door | – check if the door contact is in alarm mode. Disable door contact. |
Can’t enter programming mode and a long beep is
heard |
– multiple buttons were pressed before trying to enter programming mode. Wait a few seconds then try again |
After pressing [5] there are 3 beeps | – card memory full |
After pressing [5] + [index code] there are 3 beeps | – the index code is already in use |
The keypad exited programming mode by itself | – if there is no input in 20 sec the keypad will
automatically exit programming mode |
WIRING DIAGRAM WITH TIME DELAY POWER SUPPLY
WIRING DIAGRAM WITH SIMPLE POWER SUPPLY
Documents / Resources
![]() |
PNI DK101 Control Access Keypad with Proximity Caed Reader [pdf] User Manual DK101, Control Access Keypad with Proximity Caed Reader |