Home » PICTOR » PICTOR AIS-140 GPS Tracker With SOS Panic Button User Manual 
PICTOR AIS-140 GPS Tracker With SOS Panic Button User Manual

DEVICE INITIALIZATION
- Connect Main Power & Ignition Input to initialize device.
- Device will take 3 – 5 min to initialize.
- Red LED Indicates that device is ON.
- Blue LED shows GSM status. If it blinks at every 1 sec it means searching for GSM network and if it blinks at 2 sec then device is registered to GSM network.
- Green LED shows GPS status. If GPS fix then it will remain ON otherwise it will keep blinking.
- After device is initialized and GPS is fix, it will start sending packets to server..
IMPORTANT INSTRUCTIONS FOR SMS COMMANDS
- Keep SMS delivery report ON in your mobile phone before sending SMS commands.
- Wait for 60 sec for device response, after the SMS is delivered.
- If there is no response from device in 60 sec then send SMS command again.
- If SMS command is sent, then don’t send next SMS command before 60 sec or device response.
- If SMS not delivered in 60 sec, then send the command again.
OTA SMS COMMANDS
There are 3 types of commands:
- SET Commands: To set device parameter values
- GET Commands: To retrieve device parameter values
- CLR Commands: To clear device parameters
Format:
SET Command: #<4 digit password>#SET:#;
GET Command: #<4 digit password>#
GET:#; CLR Command: #<4 digit password>#CLR:#;
OTA SMS Commands are as below:
1 |
Device Parameter |
Private Server IP Port |
Description |
Main Server IP Port on which customer will have live tracking facility |
Parameter ID |
PIP |
SET Command |
#1234#SET:PIP#192.168.1.1,9001; |
GET Command |
NA |
CLR Command |
NA |
2 |
Device Parameter |
Govt. Server IP Port |
Description |
Govt. Primary Server IP Port for live location data and alerts |
Parameter ID |
GIP |
SET Command |
#1234#SET:GIP#192.168.1.1,9001; |
GET Command |
#1234#GET:GIP# |
CLR Command |
#1234#CLR:GIP# |
3 |
Device Parameter |
Emergency Server IP Port |
Description |
Govt. Emergency Server IP Port for panic alerts |
Parameter ID |
EIP |
SET Command |
#1234#SET:EIP#192.168.1.1,9001; |
GET Command |
#1234#GET:EIP# |
CLR Command |
#1234#CLR:EIP# |
4 |
Device Parameter |
APN |
Description |
Access Point Name for SIM operator |
Parameter ID |
APN |
SET Command |
#1234#SET:APN#airtelgprs.com; |
GET Command |
#1234#GET:APN# |
CLR Command |
#1234#CLR:APN# |
5 |
Device Parameter |
SOS Number |
Description |
Backend Control Centre Mobile Number for SMS Fallback in case of panicalerts and no GPRS connectivity |
Parameter ID |
SOS |
SET Command |
#1234#SET:SOS#9212499082; |
GET Command |
#1234#GET:SOS# |
CLR Command |
#1234#CLR:SOS# |
6 |
Device Parameter |
Vehicle Registration Number |
Description |
Vehicle Number in which device is installed |
Parameter ID |
VRN |
SET Command |
#1234#SET:VRN#DL01CE9898; |
GET Command |
#1234#GET:VRN# |
CLR Command |
#1234#CLR:VRN# |
7 |
Device Parameter |
Logs Interval 1 |
Description |
Data rate in sec when vehicle ignition is ON |
Parameter ID |
LOGS |
SET Command |
#1234#SET:LOGS#20; |
GET Command |
#1234#GET:LOGS# |
CLR Command |
#1234#CLR:LOGS# |
8 |
Device Parameter |
Logs Interval 2 |
Description |
Data rate in sec when vehicle ignition is OFF |
Parameter ID |
LOG2 |
SET Command |
#1234#SET:LOG2#600; |
GET Command |
#1234#GET:LOG2# |
CLR Command |
#1234#CLR:LOG2# |
9 |
Device Parameter |
Health Packet Time Interval |
Description |
Data rate in sec at which health packet will be sent to server |
Parameter ID |
HPTI |
SET Command |
#1234#SET:HPTI#120; |
GET Command |
#1234#GET:HPTI# |
CLR Command |
#1234#CLR:HPTI# |
10 |
Device Parameter |
Emergency Packet Time Interval |
Description |
Data rate in sec at which emergency packet will be sent to server |
Parameter ID |
EPTI |
SET Command |
#1234#SET:EPTI#60; |
GET Command |
#1234#GET:EPTI# |
CLR Command |
#1234#CLR:EPTI# |
11 |
Device Parameter |
Emergency Mode Timeout Duration |
Description |
Time in sec after which emergency mode will be off automatically |
Parameter ID |
EMTD |
SET Command |
#1234#SET:EMTD#120; |
GET Command |
#1234#GET:EMTD# |
CLR Command |
#1234#CLR:EMTD# |
12 |
Device Parameter |
Over Speed Limit |
Description |
Over speed limit in km/hr |
Parameter ID |
OSL |
SET Command |
#1234#SET:OSL#90; |
GET Command |
#1234#GET:OSL# |
CLR Command |
#1234#CLR:OSL# |
13 |
Device Parameter |
Harsh Acceleration Limit |
Description |
Threshold for harsh acceleration in g |
Parameter ID |
HAL |
SET Command |
#1234#SET:HAL#20; |
GET Command |
#1234#GET:HAL# |
CLR Command |
#1234#CLR:HAL# |
14 |
Device Parameter |
Harsh Breaking Limit |
Description |
Threshold for harsh breaking in g |
Parameter ID |
HBL |
SET Command |
#1234#SET:HBL#20; |
GET Command |
#1234#GET:HBL# |
CLR Command |
#1234#CLR:HBL# |
15 |
Device Parameter |
Rash Turn Limit |
Description |
Threshold for rash turn in km/hr |
Parameter ID |
RTL |
SET Command |
#1234#SET:RTL#30; |
GET Command |
#1234#GET:RTL# |
CLR Command |
#1234#CLR:RTL# |
16 |
Device Parameter |
IMEI |
Description |
To get device IMEI number |
Parameter ID |
IMEI |
SET Command |
NA |
GET Command |
#1234#GET:IMEI# |
CLR Command |
NA |
17 |
Device Parameter |
Immobilize ON |
Description |
To Immobilize vehicle engine (Relay at digital output 1 will be ON) |
Parameter ID |
IMON |
Command |
#1234#IMON# |
18 |
Device Parameter |
Immobilize OFF |
Description |
To mobilize vehicle engine (Relay at digital output 1 will be OFF) |
Parameter ID |
IMOF |
Command |
#1234#IMOF# |
19 |
Device Parameter |
Relay 2 ON |
Description |
To turn ON Relay at digital output 2 |
Parameter ID |
R2ON |
Command |
#1234#R2ON# |
20 |
Device Parameter |
Relay 2 OFF |
Description |
To turn OFF Relay at digital output 2 |
Parameter ID |
R2OF |
Command |
#1234#R2OF# |
21 |
Device Parameter |
Restart Device |
Description |
To restart device |
Parameter ID |
RST |
Command |
#1234#RST#0; (To restart normally)
#1234#RST#1; (To erase all logs and restart) |
22 |
Device Parameter |
Other Parameters |
Description |
Some useful device parameters |
Parameter ID |
PAR |
Command |
#1234#PAR# |
23 |
Device Parameter |
Device Settings |
Description |
To get current settings |
Parameter ID |
GCS |
Command |
#1234#GCS# |

Documents / Resources
References