airtelgprs.com - airtelgprs Resources and Information.
User Manual for PICTOR models including: AIS-140 GPS Tracker With SOS Panic Button, AIS-140, GPS Tracker With SOS Panic Button, SOS Panic Button, Panic Button
Index of /images
AIS-140 GPS Tracker with SOS panic button, RTO Approved.
PS140 User Manual v1.0 Page 7 of 13 8 Device Parameter Logs Interval 2 Description Data rate in sec when vehicle ignition is OFF Parameter ID LOG2 SET Command #1234#SET:LOG2#600; GET Command
File Info : application/pdf, 13 Pages, 100.55KB
DocumentDocumentPS140 User Manual v1.0 PS140 User Manual v1.0 INDEX 1. DEVICE INITIALIZATION .............................................................. 2 2. IMPORTANT INSTRUCTIONS FOR SMS COMMANDS ................. 2 3. OTA SMS COMMANDS ............................................................... 3 Page 1 of 13 PS140 User Manual v1.0 DEVICE INITIALIZATION 1. Connect Main Power & Ignition Input to initialize device. 2. Device will take 3 - 5 min to initialize. 3. Red LED Indicates that device is ON. 4. Blue LED shows GSM status. If it blinks at every 1 sec it means searching for GSM network and if it blinks at 2 sec then device is registered to GSM network. 5. Green LED shows GPS status. If GPS fix then it will remain ON otherwise it will keep blinking. 6. After device is initialized and GPS is fix, it will start sending packets to server.. IMPORTANT INSTRUCTIONS FOR SMS COMMANDS 1. Keep SMS delivery report ON in your mobile phone before sending SMS commands. 2. Wait for 60 sec for device response, after the SMS is delivered. 3. If there is no response from device in 60 sec then send SMS command again. 4. If SMS command is sent, then don't send next SMS command before 60 sec or device response. 5. If SMS not delivered in 60 sec, then send the command again. OTA SMS COMMANDS There are 3 types of commands: 1. SET Commands: To set device parameter values 2. GET Commands: To retrieve device parameter values 3. CLR Commands: To clear device parameters Page 2 of 13 Format: PS140 User Manual v1.0 SET Command: #<4 digit password>#SET:<parameter id>#<value to set>; GET Command: #<4 digit password>#GET:<parameter id>#; CLR Command: #<4 digit password>#CLR:<parameter id>#; OTA SMS Commands are as below: 1 Device Parameter Private Server IP Port Description Main Server IP Port on which customer will have live tracking facility Parameter ID PIP SET Command #1234#SET:PIP#192.168.1.1,9001; GET Command NA CLR Command NA 2 Device Parameter Govt. Server IP Port Description Govt. Primary Server IP Port for live location data and alerts Parameter ID GIP SET Command #1234#SET:GIP#192.168.1.1,9001; GET Command #1234#GET:GIP# CLR Command #1234#CLR:GIP# Page 3 of 13 PS140 User Manual v1.0 3 Device Parameter Emergency Server IP Port Description Govt. Emergency Server IP Port for panic alerts Parameter ID EIP SET Command #1234#SET:EIP#192.168.1.1,9001; GET Command #1234#GET:EIP# CLR Command #1234#CLR:EIP# Page 4 of 13 PS140 User Manual v1.0 4 Device Parameter APN Description Access Point Name for SIM operator Parameter ID APN SET Command #1234#SET:APN#airtelgprs.com; GET Command #1234#GET:APN# CLR Command #1234#CLR:APN# 5 Device Parameter SOS Number Description Parameter ID Backend Control Centre Mobile Number for SMS Fallback in case of panic alerts and no GPRS connectivity SOS SET Command #1234#SET:SOS#9212499082; GET Command #1234#GET:SOS# CLR Command #1234#CLR:SOS# Page 5 of 13 PS140 User Manual v1.0 6 Device Parameter Vehicle Registration Number Description Vehicle Number in which device is installed Parameter ID VRN SET Command #1234#SET:VRN#DL01CE9898; GET Command #1234#GET:VRN# CLR Command #1234#CLR:VRN# 7 Device Parameter Logs Interval 1 Description Data rate in sec when vehicle ignition is ON Parameter ID LOGS SET Command #1234#SET:LOGS#20; GET Command #1234#GET:LOGS# CLR Command #1234#CLR:LOGS# Page 6 of 13 PS140 User Manual v1.0 8 Device Parameter Logs Interval 2 Description Data rate in sec when vehicle ignition is OFF Parameter ID LOG2 SET Command #1234#SET:LOG2#600; GET Command #1234#GET:LOG2# CLR Command #1234#CLR:LOG2# 9 Device Parameter Health Packet Time Interval Description Data rate in sec at which health packet will be sent to server Parameter ID HPTI SET Command #1234#SET:HPTI#120; GET Command #1234#GET:HPTI# CLR Command #1234#CLR:HPTI# Page 7 of 13 PS140 User Manual v1.0 10 Device Parameter Emergency Packet Time Interval Description Data rate in sec at which emergency packet will be sent to server Parameter ID EPTI SET Command #1234#SET:EPTI#60; GET Command #1234#GET:EPTI# CLR Command #1234#CLR:EPTI# 11 Device Parameter Emergency Mode Timeout Duration Description Time in sec after which emergency mode will be off automatically Parameter ID EMTD SET Command #1234#SET:EMTD#120; GET Command #1234#GET:EMTD# CLR Command #1234#CLR:EMTD# Page 8 of 13 PS140 User Manual v1.0 12 Device Parameter Over Speed Limit Description Over speed limit in km/hr Parameter ID OSL SET Command #1234#SET:OSL#90; GET Command #1234#GET:OSL# CLR Command #1234#CLR:OSL# 13 Device Parameter Harsh Acceleration Limit Description Threshold for harsh acceleration in g Parameter ID HAL SET Command #1234#SET:HAL#20; GET Command #1234#GET:HAL# CLR Command #1234#CLR:HAL# Page 9 of 13 PS140 User Manual v1.0 14 Device Parameter Harsh Breaking Limit Description Threshold for harsh breaking in g Parameter ID HBL SET Command #1234#SET:HBL#20; GET Command #1234#GET:HBL# CLR Command #1234#CLR:HBL# 15 Device Parameter Rash Turn Limit Description Threshold for rash turn in km/hr Parameter ID RTL SET Command #1234#SET:RTL#30; GET Command #1234#GET:RTL# CLR Command #1234#CLR:RTL# Page 10 of 13 PS140 User Manual v1.0 16 Device Parameter IMEI Description To get device IMEI number Parameter ID IMEI SET Command NA GET Command #1234#GET:IMEI# CLR Command NA 17 Device Parameter Immobilize ON Description To Immobilize vehicle engine (Relay at digital output 1 will be ON) Parameter ID IMON Command #1234#IMON# Page 11 of 13 PS140 User Manual v1.0 18 Device Parameter Immobilize OFF Description To mobilize vehicle engine (Relay at digital output 1 will be OFF) Parameter ID IMOF Command #1234#IMOF# 19 Device Parameter Relay 2 ON Description To turn ON Relay at digital output 2 Parameter ID R2ON Command #1234#R2ON# 20 Device Parameter Relay 2 OFF Description To turn OFF Relay at digital output 2 Parameter ID R2OF Command #1234#R2OF# Page 12 of 13 PS140 User Manual v1.0 21 Device Parameter Restart Device Description To restart device Parameter ID RST Command #1234#RST#0; (To restart normally) #1234#RST#1; (To erase all logs and restart) 22 Device Parameter Other Parameters Description Some useful device parameters Parameter ID PAR Command #1234#PAR# 23 Device Parameter Device Settings Description To get current settings Parameter ID GCS Command #1234#GCS# Page 13 of 13