Phomemo M110 Label Printer
Please read this instruction book carefully before operating the product.
Packing List
- The number of paper rolls in the list is subject to the actual 1 shipment.
Product Specifications
| Name | Label Maker |
| Model | Mll0 |
| Print technology | Thermal printing |
| Effective printing width | 20-50mm |
| Supported consumables | Pre-cut paper, black mark paper, continuous paper |
| Consumable specifications | 57mm X<!J 50mm(Max width X Max diameter) |
| Print speed | 20-45mm/s(switchable,level-5) |
| Printing density | Switchable,level-15 |
| Print resolution | 203dpi |
| Print head service life | 50KM |
|
Communication interface |
Bluetooth |
| Micro USB | |
| Product size | 113.15’86.5’62.33mm (4.45’3.4’2.45inch) |
| Power input | 5V-2A |
|
Power supply method |
Micro USB |
| Lithium battery | |
| Supported operating system | Android |
| iOS | |
| Instruction set | ESC/POS |
| Bar code | 1D bar code & 2D bar code |
| Working environment | 5°C~50°C |
| Storage environment | -20°C~60°C |
| Working humidity | 20%~85% |
| Storage humidity | 2%~95%(Non condensation) |
Product Appearance Introduction
Button function introduction
Component Description
Display settings home menu
| Options | Parameter |
| Language | English, Spanish, French |
| Print density | l(weakest),2,3,4(weak),5,6(Normal),7,8,9,10(Dark),ll,12,13, 14,15(Darkest) |
| Print speed | l(Slowest),2(Slow),3(Normal),4(Fast),5 (Fastest) |
| Paper gap type | Continuous, Gap, Blackmark |
| Auto power OFF | NO Close,5 Minutes,15 Minutes,30 Minutes,l Hour,2 Hour,
4 Hour,8 Hour,24 Hour |
| Restore to Factory Settings | Press the power button to restore |
| Firmware version | Display Firmware version |
| Device address | Display device address |
Screen hint
| Content | State |
| Shutting down | Battery lower than 1% |
| Printing … | Printing regularly |
| Feeding … | Press Feed button |
| High temperature please wait | Print head overheated |
| No Paper .. | No paper in the bin or paper is installed incorrectly |
| The paper cover is opened | The paper cover is opened |
Printer Paper Roll Installation
- Long press the power button for 3s.
- Hold both sides of the printer paper compartment cover(both sides of the paper outlet) with the hand, and open the paper compartment cover forcefully with the finger cushion upwards.
- Take out the label paper mounting bracket in the paper compartment.
- Remove the left baffle, put in the label paper roll (label printing side down), and push the left baffle to the right.
- Align the installed label roll holder with the card slots on both sides and put it into the paper compartment.
- Pull out part of the paper ( approximately 15mm above the paper exit), and close the paper compartment cover.
- The printer feeds paper automatically to position the gap of label paper, and then the paper roll installation is complete.
- After the first operation or each time you replace the consumables, the printer will automatically feed the paper, so that the printer can position the label to avoid there will be incomplete printing, missing, non-aligned, etc.
App Download Method
- This product needs to be connected to the printer in the App.
- Due to the requirements of a mobile phone system, the Android mobile phone will use the user’s geographic location when connecting, so the user needs to turn on the GPS and confirm the authorization.
Method I:
- Please use your mobile phone to scan the QR code to download the App.
Method II:
- Search “Print Master” to download the App.
Label Maker Connection
- Turn on GPS (Android mobile phone only).
- Open the App.
- Click to search Connect Now for the device.
- Connect immediately.
- When connecting the device to the App, please make sure that your Label Maker is turned on and the Bluetooth of your mobile phone is turned on.
- Due to the requirements of a mobile phone system, the Android mobile phone will use the user’s geographic location when connecting, so the user needs to turn on the GPS and confirm the authorization.
Confirm the Label Size
Method I:
- Check the label paper packaging.
- Please refer to the actual size used.
Method II:
- Use a ruler to measure.
Printing Guide—New Label
- After clicking “New customize the label size and paper type.
- Customize the label size.
- Click” (T)” to input text.
- After editing, click on “Print”
Printing Guide Template Select the “Label Paper
- Click “Label Paper.
- Select the label paper template.
- Click” (T)” to input text.
- After editing, click on “Print.
Printing Guide Edit function description
- Shortcut keys
- Editing function
- App functions will be updated with new functions irregularly please refer to the actual function.
How to Deal with Common Problems
| Serial number | Common problem | Treatment |
| 1 | With paper in the bin, still no paper is detected on the screen. What’s the matter? | Referring to the instructions, check whether the paper is in place on the right side of the Label Maker. Pull out the paper a bit from the outlet, allowing it in between the upper and lower paper sensors, and close the bin cover. |
| 2 | Long-press the power key, what if no response? | The Label Maker may be in a power failure. Restart it after charging for half an hour. |
| 3 | What if the automatic shutdown of a Label Maker? | (1) Check whether the App has set the automatic shutdown time; |
| (2) If the power is too low, it will automatically shut down in need of a timely charge. | ||
| 4 | What if the Label Maker refuses to charge? | (1) Please charge for at least half an hour; |
| (2) Manual reset. There is a reset plughole (reset hole) beside the printer charging port. Just press for 1-2 seconds with a pin and let go; | ||
| (3)Please check whether the charger uses SV-lA or 5V-2A for charging; | ||
| (4) Replace the charger or move to another outlet; | ||
| (5) In case the above method still fails, please contact the local dealer for replacement. | ||
| 5 | What if the Label Maker refuses to charge? | (1) Press the power key to cancel; |
| (2) Manual reset. There is a reset plughole (reset hole) beside the printer charging port. Just press for 1-2 seconds with a pin and let go. | ||
| 6 | What if the paper is blank after printing? | (1) The paper roll is installed reversely. Arrange the printing paper in the other direction, making sure that the correct printing side is facing down, and keep it to the right side. |
| (2) If the paper is blank during the printing gap, please check whether the Label Maker display menu has correctly selected “label paper”. | ||
| 7 | Fuzzy printed content | (1) Check whether the label roll is in the storage period or whether there are foreign matters, clean or replace another; |
| (2) According to the instructions, wipe the printing area with an alcohol swab to ensure that there is no dirt on the print head. | ||
| 8 | Indirect skip or incomplete printing content occurs | (1) Cleanse the printer thermistor and paper outlet according to the instructions; |
| (2) Reinstall the paper roll bracket once, and manually press the paper feeding key once to allow the printer to recognize the paper gap position. | ||
| (3) Check whether the paper size and software print template match. | ||
| 9 | How to solve the problem that the printer does not run smoothly or feeding failure in the process of paper feeding or printing? | (1) The paper roll bracket is too tight or stuck. Generally, it is about 1mm of the Appropriate gap between the roll and the baffles on both sides, which can ensure smooth feeding without paper jams. |
| (2) According to the instructions, wipe the printing area and paper outlet area of the Label Maker with an alcohol swab, touch the printing area with your hand to check for no stickiness, and then try to print. | ||
| 10 | What if multiple mobile phones are simultaneously connected, but can’t be functioning? | (1) A printer can function only connected to one mobile phone, rather than multiple ones at the same time. |
| (2) When connected to another phone, please first disconnect the connected one. |
Warranty Description
Thank you for choosing the label printer products produced by our company.
- We will provide customers with reliable”replacement/return” support during the one-year warranty period from the date of purchase;
- Please keep the warranty card in a safe place so that you can read it when needed.
- If you have any problem or need on our product or this user manual, please feel free to contact our customer services. We will do our best to help you.
- NOTE: If the supporting software is updated, it will be compiled into the new version of the manual without notice.
FCC
Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference,
- this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used per the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF warning for Portable devices:
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
Warranty/Maintenance Card
- Replace
- Return
| User Information | Name: Gender:
Phone: |
| Address: | |
| Product Information | Date of purchase: |
| Product order number: | |
| Product serial number: | |
| Reason for Return (Replace/ Repair/ Request Maintenance) | Fault description: |
Documents / Resources
 | M110 Label Printer |
References
- User Manualmanual.tools
Published: November 19, 2023
どうやって、文字入力するか不明。
How do I input text?
To input text using your Phomemo M110 Label Printer, you will primarily use the associated mobile application, "Print Master". Here are the general steps based on the manual:
The app also offers various editing functions, including inserting icons, borders, pictures, dates/times, 1D/QR codes, lines, shapes, and even importing tables. For more detailed editing options, refer to the "09. Printing Guide—Edit function description" section in your manual.
Read the full Q&A page